Sony CPJ-200 - Manuel (Page 6)

For the Customers in Canada
This cippciratus complies w ith the Class B limits for
radio noise emissions set out in Radio Interference
Rec.ulations.
CAUTION
TO PRHVENT ELECTRIC SHOCK, MATCH WIDE
BI ADE O E PLUG TO WIDE SLOT, FULLY INSERT.
Before You Begin
Deciding where you want to watch the
projector
Locate the unit with the lens pointed toward the
projected plane.
For the distance to and size of the projected plane,
refer to the table below.
Distance to the
projected plane Size of the projected plane
3 feet (1 m) Approx. 18 X 13
V'
inches
(470 X 330 mm)
6 feet ( 2 m) Approx. 37 V« X 28 '/■ ' inches
(960 X 720 mm)
8 feet (2.3m) Approx. 47 ' / 4 X 35 V: inches
(1200 x900 mm)
9
feet (3 m) Approx. 57 ' /2 X 43 inches
(1460x1100 mm)
11 feet (3.5 m) Approx. 66 V-i X 49 inches
(1670 x1260 m m)
Recommended distance to the projected plane is 11
feet (3.3m).
Connecting to Video Equipment
(See illustration □ .)
Connect the unit to a video cassette recorder, video
camera recorder, or other video equipments w ith the
supplied A/V connecting cable.
When connecting, turn off the power of the unit and
the video equipment.
Connecting to a video cassette recorder [a]
Connecting to a video camera recorder [b]
If your video camera recorder has a VIDEO/AUDJO
IN/OUT selector switch, set it to OUT.
Enjoying High Quality Picture
and Sound
If your video equipment has an S X’lDEO jack, \'ou can
enjoy a high quality picture. Also \ ou can enjov high
quality sound by connecting to active speakers.
Connecting to video equipment with S
VIDEO jack (See illustration Q.)
Connect with the A/V connecting cable (supplied) and
S \-ideo cable (not supplied}.
The VIDEO (vellow) plug does not need to be
connected. But e\ en if it is connected, this unit
automatical!v selects S VIDEO signal.
Note on 5 video cable
Connect the plug u'ith the è mark upw ard t(.> the jack.
Connecting to Active Speakers (See
illustration B.)
Connect the plug of the active speakers (not supplied)
to the PHONES (headphones) jack of the unit.
The optional Sonv acth’e .speakers SRS-A91 are
recommended.
Connecting to a HiFi stereo System
(See illustration Q.)
Connect the audio plugs of \ ideo equipment to a HiFi
stereo system. You can listen to sound from a HiFi
stereo system. For details, refer to the HiFi stereo
system instruction manual.
Replacing the Bulb (see
illustration
Q.)
When the bulb in the unit wears out. replace with a
new one.
As the bulb is too hot to touch immediately after use,
wait for 30 minutes belore replacing.
1 Disconnect the AC plug.
Leave the unit for 30 minutes.
2 Loosen the screw on the bulb-cover and
pull out the cover.
Loosen the screw with a coin, etc.
3 Make sure that the bulb is cool. Then pull it
out and replace with a new one.
When replacing the bulb, put the bulb's carton box
on the bulb and pull it out holding the box.
4 Put back the bulb-cover and screw down.
Halogen bulb life
The supplied bulb, Halogen bulb XB-CPJIOO lasts for
approximately 200 to 600 hours in continuous use.
The time differs in accordance with conditions of use.
Replacement bulb
When the supplied bulb wears out, use bulb X13-
CPjlOO manufactured by Sonv.
If any other type of bulb is used, the power of the unit
may not activate or it may cause malfunction.
Note on the bulb
• Do not touch the bulb immediately after use as it is very
hot.
• Do not touch the surface of the bulb and the inside of the
reflector. If they become dirty’/ the efficiency of the bulb
may decrease.
• Do not drop or knock the bulb.
• After replacing the bulb, be sure to close the buib-co\ er.