Swiss+Tech Hunting/Fishing 7-in-1 - Manuel

LED FLASHLIGHT
• Press black button (A) to turn on flashlight.
• Release to turn off.
QUICK RELEASE
• Press the spring-loaded, wire clip (6) for
quick, easy attachment to or removal from
key rings, backpacks, etc.
Made in China. MMMMMMMMI ™ and MI ™ are
trademarks of Swiss+Tech Products. Specifications
are subject to change without notice.
©2013 Swiss+Tech Products, Solon, OH 44139 USA
Hunting/Fishing
7-in-1
www.swisstechtools.com
800-414-8799
ST74130
Limited LIFETIME Warranty
This product is covered by a Limited Lifetime Warranty
to the original purchaser in that this product is free from
defects in workmanship and materials. During the
warranty period, this product will either be repaired or
replaced with a product of equal or greater value,
excluding any custom engraving or printing.
Damage through normal wear and tear (including
battery expiration and surface coatings), repair or
alteration, misuse, abuse, neglect, accident, improper
storage and handling, fire, negligence, improper
cleaning, circumstances not directly attributable to
manufacturing defects, or act of God is not included.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO, IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR USE.
This warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state. Simply return your SWISS+TECH ® brand product
postpaid and insured to:
Swiss+Tech Products
30725 Solon Industrial Pkwy
Solon, OH 44139 USA
EASY BATTERY REPLACEMENT
• Using a small Phillips screwdriver, loosen the
captive screw (screw stays in battery cover)
on the back of your All Purpose Modular Tool.
• Lift off the battery cover.
• Remove old batteries and replace with 3 new
CR1025 button cell batteries.
• Replace battery cover and tighten screw
gently. Be sure not to over tighten.
REMOVE
PULL TAB
BEFORE USE
CR1025 Button Cell Batteries (3),
Positive Side (+) Toward On/Off Button
TOOL USE
• Use only one tool at a time.
• Torque gently, these tools are not designed
for heavy-duty use.
• Close tools when not in use.
This product contains button batteries.
IF SWALLOWED, batteries could cause
severe injury or death in just 2 hours.
SEEK MEDICAL ATTENTION IMMEDIATELY.
• Always purchase the correct size and
grade of battery most suitable for the
intended use.
• Clean the battery contacts and also those
of the device prior to battery installation.
• Ensure the batteries are installed
correctly with regard to polarity (+ and -).
• Remove used batteries promptly.
• Replace all batteries of a set at the
same time.
BATTERY WARNINGS:
Modular
Tool
System
Battery Cover
This product features a sharp knife blade. Always
position the cutting edge away from the user.
CAUTION:
NOTE: Latch (B) will close only when tool pack
is securely in place. (Hint — tool pack metal
will be see in Notch D but not in Notch E).
See instructional video and accessories at www.swisstechtools.com/toolpack
1. Open any tool but knife (Figure 1).
2. Pull up release latch B (Figure 1).
3. Grasping the open tool, slide tool pack C
back to disengage from housing (Figure 1),
then rotate clockwise (Figure 2) to remove.
4. Reverse the order to reassemble
CHANGING TOOL PACKS
AND HOUSINGS 1
3
4
5
7
6
2
1. LED Flashlight
2. Hook Remover
3. Fish Scaler
4. Knife
5. Pliers
6. Wire Cutter
7. Quick Release Clip
B
Figure 1
D E
Figure 2
C