JVC KD-R412 Manuel d'utilisation

Installation / installation, Warnings / avertissements

Advertising
background image

1

KD-R412/KD-R411/KD-R35

Installation/Connection Manual
Manuel d’installation/raccordement

ENGLISH / FRANÇAIS

1009DTSMDTJEIN

EN, FR

© 2009 Victor Company of Japan, Limited

GET0624-017A

[E/EU]

Bracket / Support *

2

Pocket / Poche

Flat head screws (M5 × 8 mm) / Vis à tête plate (M5 × 8 mm) *

2

INSTALLATION / INSTALLATION

When installing the unit without using the sleeve / Lors de l’installation de l’appareil
scans utiliser de manchon

In-dash mounting / Montage encastré

• To prevent short circuits:
– Disconnect the battery’s negative terminal and make all electrical connections before installing the unit.
– Cover the terminals of the UNUSED leads with insulating tape.
• Be sure to ground this unit to the car’s chassis again after installation.
• Replace the fuse with one of the specified rating.
• Connect speakers with a maximum power of more than 50 W

(impedance of 4 Ω to 8 Ω). Otherwise, change the <AMP GAIN> setting.
(See page 16 of the INSTRUCTIONS.)

• The heat sink becomes very hot after use. Be careful not to touch it

when removing this unit.

• Pour éviter les courts-circuits:
– Déconnectez la borne négative de la batterie et réaliser toutes les connexions avant d’installer l’appareil.
– Recouvrez les prises des fils NON UTILISÉS avec du ruban isolant.
• Assurez-vous de raccorder de nouveau la mise à la masse de cet appareil au châssis de la voiture après

l’installation.

• Remplacer le fusible par un de la valeur précisée.
• Connectez des enceintes avec une puissance maximum de 50 W (impédance de 4 Ω à 8 Ω). Sinon, changez le

réglage <AMP GAIN>. (Voir la page 16 du MANUEL D’INSTRUCTIONS.)

• Le dissipateur de chaleur devient très chaud après usage. Faire attention de ne pas le toucher en retirant cet

appareil.

12 V DC, NEGATIVE ground / 12 V CC, masse NÉGATIVE

To the car system / Au système autoradio

You need the installation kits which corresponds to your car. / Vous avez besoin des kits
d’installation correspondants à votre voiture.

Check the battery system in your car /
Vérifiez le système de batterie de
votre voiture

WARNINGS / AVERTISSEMENTS

Removing the unit / Retrait de l’appareil

Release the rear section first... / Ouvrez la section arrière en premier...

The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC IN-CAR ENTERTAINMENT dealer or a company supplying kits.

Heat sink / Dissipateur de chaleur

L’illustration suivante est un exemple d’installation typique. Si vous avez des questions ou avez besoin
d’information sur des kits d’installation, consulter votre revendeur d’autoradios JVC.

Bend the appropriate tabs to hold the sleeve
firmly in place.
Tordez les languettes appropriées pour maintenir le
manchon en place.

Install the unit at an angle
of less than 30˚.
Installez l’appareil avec un
angle de moins de
30˚.

*

1

*

1

When you stand the unit, be careful not to damage the fuse on the rear.

*

2

Not supplied for this unit.

*

1

Lorsque vous mettez l’appareil à la verticale, faire attention de ne pas endommager le fusible situé sur l’arrière.

*

2

Non fourni avec cet appareil.

PRECAUTIONS on power supply and speaker connections

• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be

seriously damaged.

• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in

your car.

PRECAUTIONS sur l’alimentation et la connexion des enceintes

• NE CONNECTEZ PAS les fils d’enceintes du cordon d’alimentation à la batterie; sinon, l’appareil serait

sérieusement endommagé.

• AVANT de connecter les fils d’enceintes du cordon d’alimentation aux enceintes, vérifiez le câblage des enceintes

de votre voiture.

Part list / Liste de pièces
A Control panel / Panneau de

commande (×1)

B Sleeve / Manchon (×1)
C Trim plate / Plaque d’assemblage

(×1)

D Power cord / Cordon d’alimentation

(×1)

E Handles / Poignées (×2)

Do the required electrical connections
(see page 2).
Réalisez les connexions électriques (voir
page 2).

Install_KD-R412_017A_f.indd 1

Install_KD-R412_017A_f.indd 1

11/4/09 4:30:14 PM

11/4/09 4:30:14 PM

Advertising