Whirlpool GZ5736XR Series - Manuel (Page 4)

4
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Hood location should be away from strong draft areas, such as
windows, doors and strong heating vents.
Grounded electrical outlet is required. See “Electrical
Requirements” section.
It is recommended that the hood be fastened into solid wood. If
fastening into drywall or other material, wall anchors or screws
with toggle nuts (purchased separately) must be used.
This hood is factory set for non-venting (recirculating)
installations. For vented installations see “Installation Instructions”
section.
If this hood will be used as a non-vented installation you will also
need to purchase a 30" (76.2 cm) Filter Kit, No. 4396291 or
36" (91.4 cm) Filter Kit, No. 4396292 from your dealer.
All openings in ceiling and wall where the hood will be installed
must be sealed.
In U.S. only: For power cord connected installations, a UL-listed
range hood cord-connection kit (part no. 99524057) must be
used. Cord kit has not been evaluated for use in Canada.
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the safety instructions provided with any tools
listed here.
Tools needed:
■ level
■ compass or 8" (20.3 cm) circle template
■ flat blade screwdriver
■ Phillips screwdriver
■ pliers
■ metal snips
■ drill
■ 1 ¹⁄₄" and ¹⁄₈"drill bits
■ pencil
■ ruler
■ keyhole saw
■ saber saw
■ duct tape
Parts needed:
■ UL- or CSA-listed, ¹⁄₂" (12.5 mm) strain relief
(used with direct wiring only)
■ power supply cable
■ 7" (17.8 cm) round damper if using
7" (17.8 cm) round vent system
■ 2 twist-on electrical wire connectors
INSTALLATION REQUIREMENTS
29-7/8" (75.9 cm) model: GZ5730 Series
35-7/8" (91.1 cm) model: GZ5736 Series
7-1/4"
(18.4 cm)
20"
(50.8 cm)
12-5/8"
(32.1 cm)
Electrical Requirements
IMPORTANT: The hood must be electrically grounded in
accordance with local codes and ordinances, or in the absence of
local codes, with the National Electrical Code, ANSI/NFPA 70,
latest edition, or Canadian Electrical Code, CSA C22.1.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that
the ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park, Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, Ohio 44131-5575
■ A 120-volt, 60-Hz, AC-only, 15-amp, fused electrical circuit is
required. A time-delay fuse or circuit breaker is also
recommended. It is recommended that a separate circuit
serving only this hood be provided.
■ Do not ground to a gas pipe.
■ Check with a qualified electrician if you are not sure range
hood is properly grounded.
■ Do not have a fuse in the neutral or ground circuit.
■ The range hood must be connected with copper wire only.
■ The range hood should be connected directly to the fused
disconnect (or circuit breaker) box through flexible armored or
nonmetallic sheathed copper cable.
■ A UL- or CSA-listed strain relief must be provided at each end
of the power supply cable. Wire sizes (copper wire only) and
connections must conform with the rating of the appliance as
specified on the model/serial rating plate.
■ Wire sizes must conform to the requirements of the National
Electrical Code, ANSI/NFPA 70, latest edition, or CSA
Standards C22.1-94, Canadian Electrical Code, Part 1 and
C22.2 No. 0-M91, latest edition, and all local codes and
ordinances.
Product Dimensions