Jenn-Air Electric Dawndraft Slide-In Range JES9800 - Manuel (Page 25)

25
Oven Door
For normal range use, it is not suggested to remove the oven
door. However, if removal is necessary, make sure the oven is off
and cool. Then, follow these instructions. The oven door is heavy.
To Remove:
1. Open oven door to the first stop position (opened about
4" [10.0 cm]).
2. Grasp door at each side. Do not use the door handle to lift
door.
3. Lift up evenly until door clears hinge arms.
To Replace:
1. Grasp door at each side.
2. Align slots in the door with the hinge arms on the range.
3. Slide the door down onto the hinge arms until the door is
completely seated on the hinges. Push down on the top
corners of the door to completely seat door on hinges. Door
should not appear crooked.
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
Nothing will operate
■ Has a household fuse blown, or has a circuit breaker
tripped? Replace the fuse or reset the circuit breaker. If the
problem continues, call an electrician.
Cooktop will not operate
■ Is the control knob set correctly? Push in knob before
turning to a setting.
Excessive heat around cookware on cooktop
■ Is the cookware the proper size? Use cookware about the
same size as the surface cooking area, element or surface
burner. Cookware should not extend more than ½" (1.3 cm)
outside the cooking area.
Hot surface indicator light stays on
■ Does the hot surface indicator light stay on after controls
have been turned off? See “Hot Surface Indicator Light” in
“Cooktop Controls” section.
Cooktop cooking results not what expected
■ Is the proper cookware being used? See “Cookware”
section.
■ Is the control knob set to the proper heat level? See
“Cooktop Use” section.
■ Is the range level? Level the range. See the Installation
Instructions.
Oven door will not open
■ Has a self-cleaning cycle been started? The oven door is
locked during a self-cleaning cycle. See “Self-Cleaning
Cycle” section.
■ Is the oven control and oven door lock set? See “Locking
the Oven Control and Oven Door” section.
Oven will not operate
■ Is the electronic oven control set correctly? See
“Electronic Oven Control” section.
■ Has a delay start been set? See “More Options” section.
■ On some models, is the Control Lock set? See “Locking
the Oven Control and Oven Door” section.
■ On some models, is the Sabbath Mode set? See “Sabbath
Mode” in the “Setup” section.
Oven temperature too high or too low
■ Does the oven temperature calibration need adjustment?
See “Temp Adjust” in the “Setup” section.
Display shows messages
■ Is the display showing “FAULT DETECTED?” A fault has
been detected. Follow the displayed directions “PRESS
ENTER TO TRY AGAIN” or “DISABLE POWER TO CLEAR.” If
the fault does not clear, reappears, or “FEATURE NOT
AVAILABLE” is displayed, call for assistance or service.
■ Is “SAB” flashing?
Oven is in Sabbath Mode. To cancel, press and hold the
SETUP pad for 5 seconds.
Self-Cleaning cycle will not operate
■ Is the oven door open? The dislpay will show “CLOSE
DOOR.” Close the oven door all the way.
■ Has the function been entered? See “Self-Cleaning Cycle”
section.
■ On some models, has a delay start Self-Cleaning cycle
been set? See “Self-Cleaning Cycle” section.
■ Has a delay start been set? See “More Options” section.
■ Is the control in Sabbath Mode? See “Sabbath Mode” in
the “Setup” section.
■ Is the oven temperature above 400°F (205°C)?
Let the oven cool before using the self-cleaning cycle.