JVC MX-KC45 - Manuel (Page 29)

26
En
glish
Troubleshooting
• If you are having a problem with your System, check this list for a possible solution before calling for service.
• If you cannot solve the problem from the hints given here, or the System has been physically damaged, call a qualified person, such as your
dealer, for service.
Symptom Possible Cause Action
No sound is heard. • Connections are incorrect, or loose.
• Headphones are connected.
• Check all connections and make correc-
tions. (See pages 4 to 6.)
• Disconnect the headphones.
Poor radio reception • The antenna is disconnected.
• The AM Loop Antenna is too close to the
System.
• The FM Wire Antenna is not properly
extended and positioned.
• Reconnect the antenna securely.
• Change the position and direction of the
AM Loop Antenna.
• Extend FM Wire Antenna to the best recep-
tion position.
The disc tray does not open. • The AC power cord is not plugged in.
• Tray is locked. • Plug the AC power cord.
• Unlock the tray. (See page 15.)
The CD skips. The CD is dirty or scratched. Clean or replace the CD. (See page 25.)
The CD does not play. The CD is upside down. Put the CD in with the label side up.
The MP3/WMA disc does not play. • No MP3/WMA files are recorded on the disc.
• MP3/WMA files do not have the file exten-
sion —.wma or .mp3 in thier file names.
• MP3/WMA files are not recorded in the
format compliant with ISO 9660 Level 1 or
Level 2.
Replace the disc.
The readout time of the MP3/WMA disc is too
long. The readout time varies with the complexity of
the recording configuration. Do not use too many hierarchies and folders
when recording. Also, do not record any other
types of audio tracks together with MP3/WMA
files. (See page 11.)
The cassette holder cannot be opened. During tape playing, the power cord was un-
plugged. Plug in the power cord, and turn on the System.
Unable to record. Cassette record protect tabs are removed. Cover holes on back edge of cassette with tape.
Unable to operate the Remote Control. • The path between the Remote Control and
the sensor on the Unit is blocked.
• The batteries have lost their charge.
• Remove the obstruction.
• Replace the batteries.
Operations are disabled. The built-in microprocessor has malfunctioned
due to external electrical interference. Unplug the System then plug it back in.
“PROTECT” appears on the display, then the
power goes off. The speaker wire leads come in contact with
each other. Check the connections and make corrections.
(See page 5.)
Specifications
Amplifier
Output Power 200 W per channel, min. RMS, driven
into 6
Ω at 1kHz, with no more than
10% total harmonic distortion
Input Sensitivity/Impedance (1 kHz)
AUX IN 400 mV/50 k
Ω
Speaker terminals 6 - 16 Ω
Phones 32
Ω - 1 kΩ
17 mW/ch output into 32
Ω
Cassette Deck Section
Frequency Response
Type I (NORMAL) 63 Hz - 12 500 Hz
Wow And Flutter 0.15% (WRMS)
CD Player
CD Capacity 3 CDs
Dynamic Range 85 dB
Signal-To-Noise Ratio 85 dB
Wow And Flutter Unmeasurable
Tuner
FM Tuner
Tuning Range 87.5 MHz - 108.0 MHz
AM Tuner
Tuning Range 530 kHz - 1 710 kHz
Unit
Dimensions 270 mm × 307 mm × 492mm (W/H/D)
Mass Approx. 9.3 kg
Speaker Specifications (each unit)
SP-MXKC45
Type 3-way bass-reflex type
Speaker Unit Woofer: 16 cm cone × 1
Mid: 5cm cone × 1
Tweeter: 2 cm dome × 1
Power Handling Capacity 200 W
Impedance 6
Ω
Frequency Range 45 Hz - 22 000 Hz
Sound pressure level 87 dB/W·m
Dimensions 220 mm × 324 mm × 238 mm(W/H/D)
Mass Approx. 3.6 kg
Accessories
AM Loop Antenna (1)
FM Wire Antenna (1)
Remote Control (1)
Batteries R6P (SUM-3)/AA (15F) (2)
Power Specifications
Power Requirements AC 120 V , 60 Hz
Power Consumption 180 W (power on mode)
23 W (in Standby mode)
1 W (in ECO mode)
Design and specifications are subject to change without notice.
MX-KC45(C)_Eng.book Page 26 Thursday, January 19, 2006 11:13 AM