JVC MX-KC45 - Manuel (Page 17)

14
Using the CD Player
En
glish
Resume Play for Audio CD and
MP3/WMA Disc
You can store the point of the track where you stopped playback.
By pressing CD
6 button, you can start playback again from the
point where you stopped it.
On the Unit ONLY
Press the SET/RESUME button for 2 seconds until both
“RESUME” and “ON” appear on the display.
To turn off the resume play, press the SET/RESUME button
for 2 seconds until both “RESUME” and “OFF” appear on the display.
• To playback from the first track while resume play is acti-
vated, press
7
button twice during playback.
The following operations will erase the memory of the
track number that you have stopped playback when
• Pressing CD Open/Close
0 button to eject the disc.
• Pressing CD1-CD3 button or DISC SKIP button to change
the disc to play.
Programming the Playing Order
of the Tracks
You can program the playing order of the tracks on all the CDs. Note
that you can only make a program when the CD Player is stopped.
❏ You can program up to 32 tracks in any desired order including
the same tracks.
For MP3/WMA discs
• If you try to select a MP3/WMA disc that has once been
read or played, “MP3 DISC” or “WMA DISC” appears on
the display and it can not be programmed.
• MP3/WMA disc that has not ever been read can be se-
lected in a program mode. But when playback starts,
“MP3 DISC” or “WMA DISC” appears on the display, the
program is deleted and switched to a next program.
To Make a Program
1 Load CDs.
2 In Stop mode, set the CD Player in Program
Play mode.
Press the PROGRAM button to light the “PRGM” indicator on the
display.
At the same time, “PROGRAM” appears on the display.
Each time you press the button, the display changes as follows:
PROGRAM
= Normal display (Normal Play) = (back to the be-
ginning)
• If a program is already made, the last step of the program will
be displayed.
3 Press one of the Disc button (CD1-CD3) to
select the CD you want to program.
The display will change to the Program Entry display.
4 Select the track you want to program.
On the Unit
While the display is blinking, press the
4 or ¢ button on the
Unit to select the track, then press the SET button within 5 seconds.
The program order number will be assigned from P-1.
On the Remote Control
Press the numeric keys to directly enter the track number. Then,
the program order number will be assigned from P-1.
• To delete the current program step, press the CANCEL button
on the Unit.
5 Repeat steps 3 and 4 to program other tracks
on the same CD or the other CD.
6 To play the program, Press the CD
6
but-
ton.
For details, see “To Play the Program You Have Made” men-
tioned below.
To confirm the programmed contents, while the CD player
is stopped, select Program mode by pressing the PROGRAM but-
ton and press the
4 or ¢ button on the Remote Control.
To delete all the tracks in the program, while the CD Player
is stopped, press the
7 button or open the tray by pressing the CD
Open/Close
0 button.
To Modify the Program, while the CD Player is stopped and the
program mode is selected, press the CANCEL button, the last track
in the program is deleted. To add new tracks to the end of the pro-
gram, repeat above steps 3 and 4.
• If you try to program a track number that does not exists
on the CD, your entry will be ignored.
• If you try to program the 33rd track, “FULL” appears on
the display.
To Play the Program You Have Made
Press the CD
6 button.
The System plays the tracks in the order you have programmed
them.
• To use Repeat Play for Program Play, press the REPEAT but-
ton to select “REPEAT” before starting playback. For details,
see “Repeating Tracks” on page 15.
❏ You can skip to a particular program track by pressing the 4
or
¢ button during Program Play.
❏ To stop playing, press the 7 button once. If you press the 7 but-
ton, while the CD Player is stopped, the program is deleted.
Disc number Track number
or
Disc number Track number
Program order number
MX-KC45(C).book Page 14 Wednesday, January 11, 2006 2:32 PM