Maytag W10295008A - Manuel (Page 23)

23
■ Is the fabric softener dispenser clogged?
Clean the fabric softener dispenser. See “Washer Care” for
details.
■ Are the laundry products in the correct dispenser
compartment?
Add the correct amounts of detergent, fabric softener or liquid
chlorine bleach to the correct compartments. Add powdered or
liquid color-safe bleach to the Main Wash compartment.
■ Is there water in the dispenser at the end of the cycle?
A small amount of water will remain in the dispenser
compartment. This is normal.
Washer odor
■ See “Cleaning Your Washer”
■ Are you using AFFRESH ® washer cleaner on a regular basis?
AFFRESH ® washer cleaner removes and avoids odor-causing
residue in all High Efficiency washers. For washers where odor is
present, use 3 tablets instead of 1 tablet. After the CLEAN
WASHER with AFFRESH™ cycle is complete, wipe away residue
if necessary.
■ Are you using HE detergent?
Use of non-HE detergent can cause a film residue which can
result in odor.
■ Did you leave the door open after use?
This washer has a tight seal to avoid water leaks. To avoid odors
leave the door open to allow the washer to dry between uses.
Door won't unlock
■ Did all of the water drain out of the washer during the spin?
Select RINSE, DRAIN & SPIN to remove any water remaining in
the washer. The washer door will unlock at the end of the drain.
■ Is the door locked and is the “Add Clothes” light on?
Press START/PAUSE once. The door will unlock.
Washer won't power up
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
■ Is the power cord plugged into a grounded 3 prong outlet?
Plug power cord into a grounded 3 prong outlet.
■ Are you using an extension cord?
Do not use an extension cord.
■ Has a household fuse blown, or has a circuit breaker tripped?
Check that the washer is plugged into a working outlet, and
check for blown fuses. Replace the fuse, or reset the circuit
breaker. If the problem continues, call an electrician.
■ Is your voltage low?
Check electrical source or call electrician.
Washer cycle won’t start
■ Is the washer door firmly shut?
The door must be closed during operation.
■ Has a cycle been selected, but START/PAUSE has not been
selected and held for 1 second?
Press and hold START/PAUSE, for 1 second.
■ Was the door open after completion of last cycle?
The door must be opened and closed again to start a new cycle.
■ Is the door locked?
If door is locked, run a drain cycle and drain the washer.
Control won’t accept selections or won’t shut off
■ Are the touch pad controls locked?
Hold for 3 seconds the button to lock/unlock controls.
■ Are the touch pad buttons not responding?
Press POWER/CANCEL on the touch-pad twice. Check the
touch-pad/LED assembly by selecting different cycles and
changing the modifiers and options available to confirm the
touch-pad/LED assembly is responding.
Washer stops working
■ Does the washer shut down the same time in the same wash
cycle repeatedly?
Unplug washer or disconnect power. Wait 5 minutes. Plug in
washer or reconnect power. Run another cycle.
Washer won’t dispense
■ Is the washer level?
Check that the washer is level. See “Level Washer.”
■ Has the drawer dispensed detergent?
Check that the dispenser drawer is not clogged with detergent.
■ Are both the hot and cold water faucets turned on?
Check water hose connections to the washer. Check for plugged
screen in water source. Check the water supply and the water
valve.
Washer won’t fill
■ Low water pressure at home?
Check if the home has low water pressure, open the water
faucets.
■ Are both the hot and cold water faucets turned on?
Verify hot and cold valve at the water faucets are fully open.
■ Is the water inlet hose kinked?
Straighten the hoses. Check water hose connections to the
washer and make sure water supply hoses are not obstructed.
Check for plugged screen.
■ Are the water inlet valve screens clogged?
Turn off the water and remove inlet hoses from the washer.
Remove any accumulated film or particles. Reinstall hoses, turn
on water, and check for leaks.
■ Are you using HE detergent?
HE detergent is a low sudsing detergent. This is normal and will
not affect cleaning performance.
■ Low water?
This washer uses very little water to provide good cleaning
results. You will see little or no water splashing in this washer.
This is normal.