BE Pressure supply 32,000 BTU LPG Tank Top Heaters HLTT32 - Manuel (Page 4)

Model HLTT16
1. Be sure that the control knob on the regulator is in
the “OFF” position.
2. Line up the threads on the Fuel Connector Nut with
the threads on the LP cylinder valve. Turn Fuel Con-
nector Nut counterclockwise to tighten. Use a wrench
to fully tighten the nut, being careful not to overtighten.
3. Slowly open the LP cylinder valve.
4. Check all connections for leaks using a 50/50
mixture of dish soap and water. Any bubbles appear-
ing show a leak. Remove and reconnect the Connector
Nut to the valve.
Model HLTT32
1. Be sure that the control knob on the regulator is in
the “OFF” position.
2. Line up the slots in the tank collar bracket with the
tank collar ring and slide into place. Be sure the mount-
ing knob is to the outside, and tighten.
3. Line up the threads on the Fuel Connector Nut with
the threads on the LP cylinder valve. Turn Fuel Con-
nector Nut counterclockwise to tighten. Use a wrench
to fully tighten the nut, being careful not to overtighten.
4. Slowly open the LP cylinder valve.
5. Check all connections for leaks using a 50/50
mixture of dish soap and water. Any bubbles appear-
ing show a leak. Remove and reconnect the Connector
Nut to the valve.
6. Do not direct heater discharge towards any propane
cylinder located within 20 feet of the heater.
4
Never Leave Heater UNatteNded
wHiLe bUrNiNg, coNNected to a
power soUrce or wHiLe
coNNected to a fUeL soUrce.
Connecting Heater to LP Cylinder
Be sure to read and understand all of the Safety Informa-
tion in this manual before connecting the heater to the
LP cylinder. Installation must conform to local codes and
with the Standard for the Storage and Handling of Lique-
fied Petroleum Gases and ANSI/NFPA 58
Inspect the hose and regulator prior to each use of the
heater. If there is excessive abrasion or wear, or if the hose is
cut, replace it with the proper assembly shown in the parts list
prior to using the heater.
Page 4
Pinnacle Products International, Inc. Tank Top User’s Manual
NEVER LEAVE HEATER
UNATTENDED WHILE BURN-
ING OR WHILE CONNECTED
TO A FUEL SOURCE
Propane
Tank Top Heaters
Connecting Heater to LP Cylinder
Be sure to read and understand all of the Safety Information
in this manual before connecting the heater to the LP
cylinder. Installation must conform to local codes and with
the Standard for the Storage and Handling of Liquefied
Petroleum Gases and ANSI/NFPA 58
Inspect the hose and regulator prior to each use of the heater. If
there is excessive abrasion or wear, or if the hose is cut, replace
it with the proper assembly shown in the parts list prior to using
the heater.
Model PT-16-TTC
1. Be sure that the control knob on the regulator is in the “OFF”
position.
2. Line up the threads on the Fuel Connector Nut with the
threads on the LP cylinder valve. Turn Fuel Connector Nut
counterclockwise to tighten. Use a wrench to fully tighten the
nut, being careful not to overtighten.
3. Slowly open the LP cylinder valve.
4. Check all connections for leaks using a 50/50 mixture of dish-
soap and water. Any bubbles appearing show a leak. Remove
and reconnect the Connector Nut to the valve.
Models PT-32-TTC & PT-47-TTC
1. Be sure that the control knob on the regulator is in the “OFF”
position.
2. Line up the slots in the tank collar bracket with the tank collar
ring and slide into place. Be sure the mounting knob is to the
outside, and tighten.
3. Line up the threads on the Fuel Connector Nut with the
threads on the LP cylinder valve. Turn Fuel Connector Nut
counterclockwise to tighten. Use a wrench to fully tighten the
nut, being careful not to overtighten.
4. Slowly open the LP cylinder valve.
5. Check all connections for leaks using a 50/50 mixture of dish-
soap and water. Any bubbles appearing show a leak. Remove
and reconnect the Connector Nut to the valve.
6. Do not direct heater discharge towards any propane cylinder
located within 20 feet of the heater.
Swivel
Bracket
Connection Hose Tank Collar Bracket
Mounting Bolt
Knob
Wing Bolt
Plane Washer
Figure 3. Perspective view of PT-47-TTC
Figure 4. 47TTC Burner Head Options