Panasonic WV-LC1710 - Manuel (Page 6)

6
• Built-in high resolution (SXGA) panel with high contrast ratio,
wide view angle and true 8 bit full color.
• Selectable inputs, including Composite Video, S-Video,
Component Video and analog RGB signal input for personal
computer (PC).
• Automatically switchable NTSC and PAL system.
• PC display capacity which can support VGA (640 × 480) ~ SXGA
(1280 × 1024) resolutions. Picture size and position can be auto-
matically adjusted.
• One audio input and output with built in maximum speaker out-
put of 0.5 W.
• Refer all work related to the installation of this product to
qualified personnel or system installers.
• Do not block the ventilation slots on the cover.
To prevent the appliance from overheating, place it at least 5 cm
{2 inches} away from the wall.
• Do not drop metallic parts through the slots.
This could permanently damage the appliance. Turn the power
off immediately and contact qualified service personnel for ser-
vice.
• Do not attempt to disassemble the appliance.
To prevent electric shock, do not remove screws or covers.
There are no user-serviceable parts inside. Contact qualified
service personnel for maintenance.
• Handle the appliance with care.
Do not strike or shake it, as this may damage the appliance.
• Do not expose the appliance to rain or moisture nor try
to operate it in wet areas.
Take immediate action if the appliance becomes wet. Turn the
power off and refer to qualified service personnel.
Moisture may damage the appliance and also cause electric
shock.
• Do not operate the appliance beyond its specified tem-
perature, humidity or power source ratings.
Use the appliance at temperatures within 0 °C ~ +40 °C {32 °F
~ 104 °F} and humidity below 90 %.
The input power source for this appliance is 100 V AC to 240 V
AC, 50/60 Hz with AC Adapter.
• Do not use strong or abrasive detergents when cleaning
the appliance body.
Use a dry cloth to clean the appliance when it is dirty. When the
dirt is hard to remove, use a mild detergent and wipe gently.
Afterwards, wipe the remained part of the detergent in it with
a dry cloth.
• The surface of the display panel is applied by special
coating.
Do not point hard objects and wipe by abrasive material. It can
cause scratches and damages on the display panel.
• The display panel is made from a very precise technol-
ogy.
Some bright and dark spots may exist on the screen. It is operat-
ing normally if there are 99.99 % active pixels.
• Use the supplied AC Adapter.
Other AC Adapters cannot be used.
• When turning off the power supply of AC Adapter, unplug
the power supply cord or cut the power supply through
the breaker in the panel board connecting to this equip-
ment.
When installing this equipment again, place where the power
supply plug socket and breaker easily be reached..
• Image persistence may appear on the LCD after a static
image with strong contrast is continuously displayed.
Such a phenomenon is caused by an LCD characteristic. The
persistent image will disappear after a period of time.
• Onscreen setup menu.
• Auto-volt power supply from 100 V AC ~ 240 V AC (AC Adapter).
Note: The included AC power cord is for 120 V AC only. It is nec-
essary to change the AC power cord when using other power
supply other than 120 V AC.
• Metal cabinet casing. It can be mounted in an EIA standard rack
using an optional rack mount bracket.
• The mounting holes for wall mount located on the rear side
of the monitor comply with VESA standard. It can be mount-
ed in the wall by installing a commercialized wall mount.
VESA: Video Electronics Standards Association
This monitor is a 17" type LCD Monitor, using a motion adaption
IP conversion circuit and Y/C separation circuit for high definition
and high resolution of picture display.
PREFACE
FEATURES
PRECAUTIONS