Curtis SP230 - Manuel (Page 7)

6 7
EN EN
6 7
The exclamation point
within the triangle is a
warning sign alerting
you o f importan t
instructions.
arrowhead within the
triangle is a warning
sign alerting you of
"dangerous voltage"
inside the product.
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (ON BACK). NO
USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTION MANUAL
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
1. READ INSTRUCTIONS - All the safety and operating Instructions
should be read before the product Is operated.
2. RETAIN INSTRUCTIONS - The safety and operating Instructions
should be retained for future reference.
3. HEED WARNINGS - All warnings on the product and In the operating
Instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating and use Instructions
should be followed.
5. CLEANING - Unplug this product from the wall outlet before cleaning,
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
6. ATTACHMENTS - Do not use attachments not recommended by the
product manufacturer as they may cause hazards .
7. WATER AND MOISTURE - Do not use this product near water - for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub; In a wet
basement, or near a swimming pool, and the like.
8. ACCESSORIES - Do not place this product on an unstable cart,
stand tripod, bracket, or table. The product may fall, causing serious Injury
to a child or adult, and serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table recommended by the manufacturer,
or sold with the product. Any mounting of the product should follow
the manufacturer's Instructions, and should use a mounting accessory
recommended by the manufacture
9. A product and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and ca
combination to overturn.
10.VENTILATION - Slots and openings In the cabinet are provided for
ventilation and to ensure reliable operation of the product and to protect
It from overheating, and these openings must not be blocked or covered.
The openings should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not be placed In a
built-in Installation such as a bookcase or rack unless proper ventilation Is
provided or the manufacturer's Instructions have been adhered to .
11. POWER SOURCES - This product should be operated only from the
type of power source Indicated on the marking label. If you are not sure of
the type of power supply to you home, consult your product dealer or local
power company. For products Intended to operate from battery power, or
other sources, refer to operating Instruction.
12.GROUNDING OR POLARIZATION - This product may be
equipped with a polarized alternating current line plug (a plug having one
way. This is a safety feature. If you are unable to insert the plug fully into
your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
ALTERNATE WARNINGS - This product is equipped with a three-
wire grounding-type plug, a plug having a third (grounding) pin. This plug
rt
EN EN
8 9
you are unable to insert the plug into the outlet, contact your electrician
to replace your obsolete outlet, Do not defeat the safety purpose of the
grounding-type plug.
13.POWER - CORD PROTECTION - Power supply cords should
be routed so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at plugs,
convenience receptacles, and point where they exit from the product.
14.PROTECTIVE ATTACHMENT PLUG - The product is equipped
with an attachment plug having overload protection. This is a safety
feature. See Instruction Manual for replacement or resetting of protective
device. If replacement of the plug is required, be sure the service
technician has used a replacement plug specified by the manufacturer
that has the same overload protection as the original plug.
15.OUTDOOR ANTENNA GROUNDING - If an outside antenna
is connected to the receiver, be sure the antenna system is grounded
so as to provide some protection against voltage surges and built-up
static charges. Article 810 of the National Electrical Code, ANSI/NFPA
70, provides information with regard to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an antenna-discharge
unit, size of grounding conductors, location of antenna-discharge unit,
connection to grounding electrodes, and requirements for the grounding
electrode.
16.LIGHTNING - For added protection for this product during a lightning
storm, or when It Is left unattended and unused for long periods of time,
unplug It from the wall outlet and disconnect the antenna or cable system.
This will prevent damage to the product due to lightning and power-line
surges.
17.POWER LINES - An outside antenna system should not be located In
the vicinity of overhead power lines or other electric light or power circuits,
or where It can fall Into such power lines or circuits. When Installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
18.OVERLOADING - Do not overload wall outlets, extension cords,
electric shock.
19.OBJECT AND LIQUID ENTRY - Never push objects of any kind
Into this product through openings as they may touch dangerous voltage
spill liquid of any kind on the product .
20.SERVICING - Do not attempt to service this product yourself as
opening or removing covers may expose you to dangerous voltage or
l.
21.DAMAGE REQUIRING SERVICE - Unplug this product from
following conditions:
a) When the power-supply cord or plug Is damaged .
b) If liquid has been spilled, or objects have fallen Into the product.
c) If the product has been exposed to rain or water .
d) I f the product does not operate normally by following the operating
Instructions, adjust only those controls that are covered by the operating
Instructions as an Improper adjustment of other controls may result In
restore the product to Its normal operation.
e) If the product has been dropped or damaged In any way.
f) When the product exhibits a distinct change In performance - this Indicates
a need for service.