Coleman 9975 - Manuel (Page 3)

WARNING
For INSTASTART™ Lanterns only:
Do not damage mantle with electrode. Holes or
tears in mantle damage the mantle.
■ Push MANTLE onto
BURNER by grasping
MANTLE SUPPORT
RING. Support
BURNER TUBE with
other hand. Position
MANTLE onto TUBE.
(Fig. 4)
Fig. 4
■ Light bottom of
MANTLE evenly. Burn
until nothing but white
ash remains. (Fig. 5)
■ Be careful not to touch
it with finger or match.
■ Do not operate
lantern with hole in
mantle.
Fig. 5
Fig. 8
■ Reassemble lantern by installing GLOBE, and
then rotate hinged top into original position; then
insert ends of GLOBE GUARD into holes on
VENTILATOR and push in to lock (Fig. 6 and 7)
Fig. 6
■ Turn FUEL VALVE ON and then push RED
IGNITOR BUTTON several times until lantern
lights. (Fig. 13 and 14)
Fig. 9 Fig. 10
Fig. 11 Fig. 12
NOTE: To replace mantle, pull downward on
SUPPORT RING while holding BURNER TUBE.
■ Attach WIRE BAIL by hooking clips into slots
on VENTILATOR as shown. (Fig. 8)
To Light
WARNING
If you smell gas:
1. Do not attempt to light appliance.
2. Extinguish any open flame.
3. Disconnect from fuel supply.
4. Call 1-800-835-3278.
WARNING
• Replace any mantle with a hole in it. A hole
can cause lantern to overheat and create a
hazard. Never operate lantern without
heat shield.
To Fuel Lantern
DANGER
• EXPLOSION - FIRE HAZARD
• LPG mixture is heavier than air and can
accumulate in low places. If you smell gas,
leave the area immediately.
• Always attach or detach LPG source outdoors;
never while lantern is lighted, near flame, pilot
lights, other ignition sources or while lantern is
hot to touch.
• Always light & use lantern outdoors.
• This lantern must not be exposed to flammable
vapors or liquids during lighting.
• This lantern is very hot during use and can
ignite flammables too close to the mantle.
Keep flammables at least 12 inches from the
sides and 48 inches from the top of the
lantern. Keep gasoline and other flammable
liquids and vapors well away from lantern.
NOTE: Your lantern is designed to be filled by
using Coleman® PowerMax® or Coleman®
LPG cartridges.
IMPORTANT: When filling with Coleman®
PowerMax® cartridges hold lantern in upright
position as shown in Fig. 9.
When using other Coleman® LPG cartridges
turn lantern upside down to fill as shown in
Fig. 10.
■ Remove cap from LPG cartridge and save for
use later.
■ Turn SUPPORT BASE counterclockwise
and remove.
■ Insert lantern FILL VALVE into LPG
CARTRIDGE. Push LPG CARTRIDGE up
(or down depending on type of fuel cartridge
being used). Some leakage will occur - this is
normal. Hold LPG cartridge in place until sound
of fuel filling changes and sprayback occurs.
Lantern is then full.
■ Remove LPG cartridge.
■ Replace cap back onto LPG cartridge.
■ Place lantern into SUPPORT BASE. (Fig. 11)
■ Rotate EXTENSIONS on bottom of BASE out
ward to add extra stability to the lantern during
use. (Fig. 12)
Fig. 13 Fig. 14
NOTE: If lantern does not light, repeat above step
after turning fuel valve completely off. If the
lantern is wet due to rain, high humidity, etc.,
the ignitor may not spark. Use match lighting
procedure as follows.
Match Light Lantern
■ Place lighted match through hole in top of
ventilator, above mantle and open FUEL VALVE
fully. (Fig. 15)
■ Lantern will ignite. (Fig. 16)
ELECTRONIC IGNITION
Fig. 15 Fig. 16
■ Brightness may be
adjusted with FUEL
VALVE. (Fig. 17)
Fig. 17
WARNING
• BURN HAZARD
• Never leave lantern unattended when hot or
in use.
• Keep out of reach of children.
■ During operation, hold or hang the lantern
by the WIRE BAIL or place on level surface
with extensions on base fully extended.
Burn in upright position only. (Fig. 18 & 19)
Fig. 18 Fig. 19
Fig. 7
English-3