Pullman Ermator WETDRY VAC 2HP 12GL SS 120V (102 12SS) - Manuel (Page 4)

LIMITED WARRANTY
The vacuum cleaner is warranted for 1 year from the date of purchase as
shown on your distributor’s invoice. Parts not covered under warranty are
power cords, fi lters, motor brushes and squeegee blades. The warranty
covers only failure due to defective parts or workmanship and will be invalidated by improper application and abuse.
In NO circumstance should you return a failed unit to the factory. If you
experience any problems with your vacuum during the warranty period,
contact the Customer Service.
10702 N 46th Street • Tampa, FL 33617
(813)971-2223 • fax (813)971-6090
www.pullmanholtcorp.com B130121
08/10
To Connect the Hose:
A metal quick disconnect hose adapter is standard equipment
with this vacuum cleaner. Simply push the adapter onto the
intake valve until the “ball bearings” seat, then fi t the hose
connector over the end of the adapter shank. Wands an/or
tools are then fi tted to the opposite end of the hose.
Remove the metal hose adapter, use a twist and pull action.
To Operate:
The vacuum cleaner is designed to perform as a wet/dry
unit.
Dry:
With the Air Filter Assembly in place, the motor head
securely clamped, and the metal hose adapter connected to
the inlet, plug the power cable into the proper outlet. Select
the appropriate hose, wand, and/or tool and connect to the
hose adapter. The vacuum cleaner is ready for dry use.
Wet:
Convert this vacuum cleaner from dry to wet pick-up by
substituting the Water Pick-up for the Air Filter Assembly.
The purpose is to provide protection for the vacuum cleaner
bypass motor. When the maximum water level in the
vacuum cleaner collection can is reached, the safety valve
(fl oat) closes off suction, automatically preventing further
liquid intake.
NOTE:
This will cause the motor to race. Turn off motor, remove
and empty collection can. Thoroughly clean fl oat assembly.
Replace Water Pick-up Adapter and motor head, then clamp
securely. The vacuum cleaner is ready for wet use.
Care and Maintenance:
Air Filter Assembly:
The Air Filter Assembly with Never-Clog(R) Bag is the
standard fi lter unit shipped with this vacuum cleaner. This
fi lter consists of a moleskin bag and metal frame, rubber
gasket and dacron Never-Clot(R) Bag. This dacron
fi ltration fabric is designed to trap the minute dirt and dust
particles, minimizing the need for frequent replacement of
the moleskin fi lter. After each use, just tap the Never-Clog
(R) fi lter an the dust buildup falls into the collection can.
The Never-Clog(R) fi lter is also washable. Carefully remove
the rubber gasket from the metal frame and strip the fi lter
bag. To replace, stretch the Never-Clog (R) fi lter evenly
around the rim of the metal frame, and then secure with the
rubber gasket.
NOTE:
Gasket must be seated evenly of the rim of the fi lter frame
to insure proper vacuum seal. No lubrication is required.
Service of electrical parts must be performed by an
authorized service representative.
Water Pick-Up Adapter:
Large quantity water pick-up REQUIRES the Water Pick-
up Adapter. The Water Pick-up Adapter is equipped with a
safety shut-off known as the fl oat assembly.
IMPORTANT: Remove packing material from a new unity
before using and clean periodically to assure proper action.
NOTE:
When changing from wet to dry vacuuming, always rinse the
collection can with clean water. Dry the tank and replace
the Water Pick-up Adapter with the Air Filter Assembly.
Storage:
Store in a dry location indoors. Wrap the cord carefully
around the vacuum head to avoid accidental damage.
ABOUT THE VACUUM CLEANER
CAUTION
Be sure the building voltage is the same as the voltage on the
motor head nameplate and that a proper ground exists