JLG G10-43A (0160005444 & After) Operator Manual - Manuel (Page 29)

Section 2 - Avant la Mise en Service et Inspection
2-3 31200741
2.2 AUTOCOLLANTS DE SÉCURITÉ
S’assurer que tous les autocollants DANGER, AVERTISSEMENT, ATTENTION et
d’instructions ainsi que les tableaux de capacités appropriés sont lisibles et en
place. Nettoyer et remplacer selon le besoin.
ANSI
Antérieurs au N/S 0160040121
OY0483
91503108
9150-3108 REV -
M O V I N G PA RT S c o u l d c r u s h c a u s i n g d e a t h o r s e r i o u s i n j u r y.
K e e p c l e a r o f w h e e l s a n d m o v i n g p a r t s w h i l e e n g i n e i s r u n n i n g .
91503108
9150-3108 REV -
M O V I N G PA RT S c o u l d c r u s h c a u s i n g d e a t h o r s e r i o u s i n j u r y.
K e e p c l e a r o f w h e e l s a n d m o v i n g p a r t s w h i l e e n g i n e i s r u n n i n g .
1701505
(BEFORE
S/N 0160016129)
1705881
91503109
9150-3109 REV -
N O R I D E R S . R i d e r s c o u l d FA L L O F F m a c h i n e c a u s i n g d e a t h o r s e r i o u s i n j u r y.
DO NOT use Ether or other high energy starting aids.
Engine equipped with
Pre-heating system.
ENGINE EXPLOSION could result in death or serious injury.
1706300C
1706300
(PERKINS ENGINE
ONLY)
91513201
(IF EQUIPPED WITH
TILT ON JOYSTICK)
9151-3201 REV. (-)
91503098
9150-3098 REV. A
For safe operation of machine, and to minimize risk of s e r i o u s i n j u r y, R E A D A N D O B S E RV E t h e f o l l o w i n g :
6. Keep others away from machine when operating. Do not allow others to stand under boom or load. Always look in direction of travel.
7. Use extreme care when handling long, high or wide loads. Do not handle unstable or loosely stacked loads.
8. Forks must be centered under load, and spaced apart as far as possible.
9. Level machine before lifting any load above 4 feet (1.2m).
10. Improper use of machine could result in machine tipping over. If machine starts to tip over, do not leave operator's seat. Lean away from tip, and brace yourself.
11. Keep mirror(s) clean and properly adjusted. Objects in mirror(s) are closer than they appear.
5. On inclines, travel with load up-grade.
1. Only trained and authorized personnel may operate this machine. 2. Before operating, read and understand all capacity charts, operator manual and safety manuals.
3. Operator must be seated with seat belt fastened. Assure all controls are in neutral before ignition switch is turned on.
4. Do not travel with boom raised. When traveling, fully retract boom and place forks in carry position, which is approximately 4 feet (1.2 m) above ground. Tilt carriage back slightly to cradle load. Use extreme caution when turning.
91503110
CONTACTING ELECTRIC POWER L I N E S w i l l r e s u l t i n d e a t h o r s e r i o u s i n j u r y.
D o n o t p l a c e m a c h i n e o r l o a d w i t h i n 1 0 f e e t ( 3 m ) o f e l e c t r i c
9150-3110 REV - A p o w e r l i n e s .
10 FT. (3 M)
91513208
9151-3208 REV -
When lifting personnel, USE ONLY a Gradall manufactured personnel work platform, with proper personnel work platform CAPACITY CHART DISPLAYED in cab. READ AND UNDERSTAND personnel work platform Owner/Operator manual before lifting personnel.
DO NOT DRIVE machine from cab when personnel are on platform. All personnel on platform must WEAR A FULL BODY HARNESS, with lanyard attached to a designated anchorage point. When personnel are on platform, the OPERATOR MUST REMAIN SEATED in cab with personnel in direct line of sight.
OPERATE CONTROLS CAUTIOUSLY and lightly when lifting or positioning personnel.
Failure to comply could result in death or serious injury.
91503102
9150-3102 REV. -
91513192
(G9-43A)
1001112773
(G10-43A)
Diesel Engine
SERVICE INTERVALS LUBRICATION AND MAINTENANCE
MATERIAL HANDLER
9151-3192 REV(B)
U s e t h i s c h a r t i n c o n j u n c t i o n w i t h t h e " L u b r i c a t i o n & M a i n t e n a n c e " a n d " R e c o m m e n d e d L u b r i c a n t s & C a p a c i t i e s " s e c t i o n s o f t h e O w n e r / O p e r a t o r M a n u a l .
S e r v i c e i n t e r v a l s m a y n e e d t o b e m o r e f r e q u e n t t h a n t h o s e s h o w n d e p e n d i n g u p o n a p p l i c a t i o n s e v e r i t y. C o n s u l t y o u r G r a d a l l d e a l e r f o r r e c o m m e n d a t i o n s .
I t i s r e c o m m e n d e d t h a t e n g i n e o i l a n d f i l t e r, t r a n s m i s s i o n l u b r i c a n t a n d f i l t e r, t r a n s f e r c a s e l u b r i c a n t a n d a x l e l u b r i c a n t b e c h a n g e d a f t e r f i r s t 1 0 0 h o u r s o n n e w, o r r e b u i l t
LUBRICANT TYPE OR SPECIFICATION Air Cleaner Element
Fuel Filter
Engine Oil Filter
Engine Oil
Coolant
Diesel Fuel
YEARLY OR 1500 HRS 6 MO. OR 1000 HRS 3 MO. OR 500 HRS EVERY 5 WKS OR 250 HRS WEEKLY OR 50 HRS DAILY OR 10 HRS
Transmission Lubricant
Filter Transfer Case Lubricant Center Section Axle Lubricant Planetary Hubs
Filter Lubricant Hydraulic System
Breather/Filter Grease Fittings Axles (6 Pts. Ea.)
Boom Head Pivot (2 Pts.)
Boom Pivot (2 Pts.)
Extend Chain Sheave (1 Pt.) Drive Shafts (1 Pt. Ea.) Cylinder Pins(13 Pts.)
Quick Switch Pin (1 Pt.)
Retract Chain Sheave (1 Pt.) Boom Front Bottom Bearing Pads
All Other Bearing Pads
Extend/Retract Chains
Options And Attachments Stabilizer Cylinder (3 Pts.)
Attachment Pivots And Pins Tires 13.00-24 12 Ply
13.00R24 Radial
15.5-25 12 Ply
Lug Nut Torque Torque Check Check Check
Check
Check
Check
Check
Check
Check
Check Check
Check
Check Check Grease
Grease Grease
Grease
Grease
Grease Grease Grease Grease Grease Grease
Grease
Change Change Change
Change
Change
Change
Change Change
Change
Change
Change
Change
SAE 15W-40 CE Oil Etheylene Glycol
No. 2 Diesel Fuel
Mobil 424
Mobil 424
Mobil 424
Mobil 424
Mobil 424
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
See Manual
65 PSI (448 kPa)
70 PSI (483 kPa)
58 PSI (400 kPa)
350-400 Lb-Ft (475-540 Nm)
Fill
VUE DES AUTOCOLLANTS SITUÉS SUR LA PAROI DE
DROITE À L'INTÉRIEUR DE LA CABINE
(MOTEUR PERKINS
SEULEMENT)
(SUR MACHINES ÉQUIPÉES DE COMMANDE
D'INCLINAISON SUR MANIPULATEUR)
(ANTÉRIEURS AU N/S
0160016129)