Philips CD Soundmachine AZ2555 with wOOx™ Technology - Manuel

• Dès que l’achat de votre appareil
Philips est enregistré, vous avez droit à
tous les avantages dont bénéficient les
possesseurs des produits Philips.
• Remplissez et renvoyez votre carte
d’enregistrement de garantie jointe à
votre appareil sans tarder et vous béné-
ficierez de ces avantages importants.
Renvoyez votre carte d’enregistrement de garantie pour vous
assurer de recevoir tous les avantages auxquels vous avez droit.
Vérification
de garantie
Enregistrez votre produit
dans les 10 jours pour
confirmer votre droit à
une protection maximum
selon les termes et les
conditions de votre
garantie Philips.
Confirmation
de possession
Votre carte d’enreg-
istrement de garantie
prouve que vous possédez
l’appareil en cas de vol ou
de perte du produit.
Enregistrement
du modèle
Renvoyez votre carte d’en-
registrement de garantie dès
aujourd’hui pour vous assur-
er de recevoir toutes les
informations, les offres et les
bonus auxquels vous avez
droit en tant que possesseur
de ce modèle.
Cet « éclair à pointe de
flèche » indique qu’un matéri-
au non isolé, situé à l’intérieur
de l’unité, risque de provoquer un choc
électrique. Pour la sécurité de chacun,
nous vous prions de ne pas retirer le
boîtier de ce produit.
Le « point d’exclamation »
attire votre attention sur des
sujets risquant de provoquer
des problèmes de fonctionnement et
d’entretien si vous ne lisez pas les infor-
mations s’y reportant.
DANGER: NE PAS EXPOSER
CET ÉQUIPEMENT A LA PLUIE NI A
UNE HUMIDITÉ EXCESSIVE POUR
ÉVITER LES RISQUES D’INCENDIE
ET DE CHOC ÉLECTRIQUE.
ATTENTION: Pour éviter les
chocs électriques, introduire la lame la
plus large de la fiche dans la borne
correspondante de la prise et pousser
jusqu’au fond.
Cet espace vous est réservé
Inscrivez ci-dessous le numéro de série situé
à l’arrière du bloc. Conservez cette informa-
tion pour vous y reporter à l’avenir.
N ° de modèle ____________________
N ° de série ______________________
MAC5097
Connaissez ces
symboles de
ssé éccu urriitte e
A T T E N T I O N
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
ATTENTION: POUR REDUIRE LE RESQUE DE CHOC ELECTRIQUE, NE PAS ENLEVER LE COUVERCLE (NI LE PANNEAU ARRIERE). CET APPAREIL NE COMPORTE AUCUNE PIECE POUVANT TRE REPAREE PAR L’UTILISATEUR. CONFIER SON ENTRETIEN A UN TECHNICIEN QUALIFIE.
• Una vez que se registre la compra de
su aparato Philips, Ud. tiene derecho a
todas las ventajas correspondientes al
dueño de un producto Philips.
• Sírvase llenar y devolver en seguida
la Tarjeta de Registro de la Garantía
empacada con su aparato y saque
provecho de estas ventajas importantes.
Envie hoy su Tarjeta de Registro de la Garantía
para recibir todas las ventajas correspondientes.
Verificación
de la garantía
Registre su producto den-
tro de 10 días para confir-
mar su derecho a máxima
protección bajo los térmi-
nos y condiciones de la
garantía de Philips.
Confirmación
del dueño
Su Tarjeta de Registro de
la Garantía comprueba
que Ud. es el dueño del
aparato en caso de robo
o pérdida del producto.
Registro
del modelo
La devolución inmediata de
su Tarjeta de Registro de la
Garantía le garantiza que
recibirá toda la información
y todas las promociones
especiales que le corre-
sponden por ser el dueño
de su modelo.
El símbolo del «rayo» indica
que algún material no aislado
dentro de su unidad podría
resultar en una sacudida eléctrica. Para
la seguridad de todos, favor de no
remover la cubierta del producto.
El «signo de exclamación» le
llama la atención a carac-
terísticas sobre las que Ud.
debe leer la información adjunta
detenidamente para evitar problemas
de funcionamiento y mantenimiento.
ADVERTENCIA: PARA EVI-
TAR EL RIESGO DE SACUDIDA
ELECTRICA O INCENDIO, NO
EXPONGA ESTE EQUIPO A LLUVIA
NI A HUMEDAD.
PRECAUCION: Para evitar
sacudida eléctrica, introduzca la patilla
ancha del enchufe al fondo de la ranu-
ra ancha.
Para uso del cliente:
Escriba abajo el número de serie que se
encuentra en el panel posterior. Guarde
esta información para el futuro.
No. de modelo ____________________
No. de serie ______________________
MAC5097
Conozca estos
simbolos de
seguridad
PRECAUCION
RIESGO DE SACUDIDA ELECTRICA NO ABRIR
PRECAUCION: PARA REDUCIR EL RIESGO DE SACUDIDA ELECTRICA,NO RETIRE LA CUBIERTA (NI EL PANEL POSTERIOR). ESTE APARATONO CONTIENE NINGUNA PARTE QUE PUEDA SER REPARADA POREL USARIO. DE SER NECESARIO ALGUN SERVICIO O REPARACIONDEL APARATO, LLEVELO UN TECNICO CALIFICADO.
• Once your Philips purchase is registered,
you’re eligible to receive all the privileges
of owning a Philips product.
• So complete and return the Warranty
Registration Card enclosed with your
purchase at once, and take advantage
of these important benefits.
Return your Warranty Registration card today to
ensure you receive all the benefits you’re entitled to.
Warranty
Verification
Registering your product
within 10 days confirms
your right to maximum
protection under the
terms and conditions of
your Philips warranty.
Owner
Confirmation
Your completed Warranty
Registration Card serves
as verification of owner-
ship in the event of prod-
uct theft or loss.
Model
Registration
Returning your Warranty
Registration Card right
away guarantees you’ll
receive all the information
and special offers which
you qualify for as the
owner of your model.
This “bolt of lightning” indi-
cates uninsulated material
within your unit may cause
an electrical shock. For the safety of
everyone in your household, please do
not remove product covering.
The “exclamation point” calls
attention to features for
which you should read the
enclosed literature closely to prevent
operating and maintenance problems.
WARNING: TO PREVENT
FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE.
CAUTION: To prevent electric
shock, match wide blade of plug to
wide slot, and fully insert.
For Customer Use
Enter below the Serial No. which is locat-
ed on the rear of the cabinet. Retain this
information for future reference.
Model No. _______________________
Serial No. ________________________
MAC5097
Know these
ssa affe etty y
symbols
C A U T I O N
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Class II equipment symbol
This symbol indicates that the unit has a double insulation system.
Símbolo del equipo Clase II
Este símbolo indica que la unidad tiene un sistema doble de aislamiento.
Symbole d’ un appareil de classe II
Ce symbole indique que l’appareil est équipé d’un système à double isolation.
1. Lea estas instrucciones.
2. Conserve estas instrucciones.
3. Lea todos los avisos.
4. Siga todas las instrucciones.
5. No utilice este aparato cerca del
agua.
6. Para limpiar el aparato utilice sólo
un trapo seco.
7. No tape las aperturas de venti-
lación. Proceda a su instalación de
acuerdo con las instrucciones del
fabricante.
8. No instale el equipo cerca de fuentes
de calor – Como radiadores, calentadores,
estufas o cualquier otro aparato (incluyen-
do los amplificadores) generador de calor.
9. No anule la
seguridad de la
clavija de corriente
(ya sea de tipo polar-
izado o
con toma de tierra). Las clavijas polarizadas
tienen dos patillas, una más ancha que la
otra. Las que disponen de toma de tierra
tienen dos patillas y una tercera que es la
de conexión a tierra.Tanto la patilla más
ancha como la toma de tierra han sido
incorporadas a la clavija para su seguridad
personal. Si la clavija suministrada con el
equipo no es compatible con su toma de
corriente, consulte a un electricista para
sustituir la toma de corriente obsoleta.
10. Proteja debidamente el cable impi-
diendo que pueda pisarse o incluso per-
forarse, especialmente en la parte más
próxima a la clavija y en el punto de salida
del equipo.
11. Utilice exclusivamente aquellos dis-
positivos/ accesorios recomendados
por el fabricante.
12. Coloque el equipo exclusi-
vamente sobre aquellos carros,
bases, trípodes, soportes o
mesas especificados por el com-
erciante o vendidos con el
equipo. Cuando utilice un carro,
tenga cuidado al desplazar el
conjunto carro/ equipo para evi-
tar posibles daños por vuelco.
13. Desenchufe el aparato durante tor-
mentas eléctricas o cuando no vaya a ser
utilizado durante largo tiempo.
14. Confíe el mantenimiento y las
reparaciones a personal técnico especial-
izado. El equipo deberá repararse siempre
que haya resultado dañado de alguna man-
era, como por ejemplo por daños en el
cable o en la clavija, por derrame de líqui-
do sobre el equipo, por objetos que
hubieran podido introducirse en su interior,
por exposición del equipo a la lluvia o a
ambientes húmedos, cuando el equipo no
funcione con normalidad o cuando hubiera
sufrido algún tipo de caída.
15. Uso de las pilas – ADVERTENCIA: Para
prevenir escapes en las pilas, que pueden
ocasionar lesiones físicas, daños a
su propiedad o dañar la unidad:
● Instale todas las pilas correctamente, + y -
como está marcado en la unidad.
● No mezcle las pilas (viejas con nuevas o
de carbono y alcalinas, etc.).
● Extraiga las pilas cuando no vaya a usar la
unidad durante largo tiempo.
EL 6475-S003: 02/8
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near
water.
6. Clean only with dry cloth.
7. Do not block any ventilation open-
ings. Install in accordance with the
manufacturer´s instructions.
8. Do not install near any heat sources
such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
9. Do not defeat
the safety
purpose of the
polarized or
grounding-type plug. A polarized plug has
two blades with one wider than the other.
A grounding type plug has two blades and
a third grounding prong.The wide blade or
the third prong are provided for your safe-
ty. If the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being
walked on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the cart,
stand, tripod, bracket, or table
specified by the manufacturer or
sold with the apparatus. When a
cart is used, use caution when
moving the cart/apparatus com-
bination to avoid injury from
tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is dam-
aged, liquid has been spilled or objects
have fallen into the apparatus, the appara-
tus has been exposed to rain or moisture,
does not operate normally, or has been
dropped.
15. Battery usage CAUTION – To prevent
battery leakage which may result in bodily
injury, property damage, or damage to the
unit:
● Install all batteries correctly, + and - as
marked on the unit.
● Do not mix batteries (old and new or
carbon and alkaline, etc.).
● Remove batteries when the unit is not
used for a long time.
EL 6475-E004: 02/8
IMPORTANT SAFETY INSTRUCTIONS
1. Lisez ces instructions.
2. Conservez ces instructions.
3. Respectez les avertissements.
4. Suivez toutes les instructions.
5. N’utilisez pas cet appareil à proximité d’une
source d’eau.
6. Nettoyez l’appareil uniquement avec un chif-
fon sec.
7. N’obstruez aucun orifice de ventilation.
Installez l’appareil selon les instructions du
fabricant.
8. N’installez pas l’appareil près d’une source de
chaleur comme par exemple des radiateurs, bouches
de chaleur, cuisinières, ou autres appareils (même des
amplificateurs) dégageant de la chaleur.
9. Ne détruisez pas la sécurité incorporée dans la
prise de terre ou prise
polarisée fournie. Une
prise polarisée est dotée de
deux lames
dont une plus large que l’autre. Une prise de terre est
dotée de deux fiches semblables et d’une troisième,
plus large, qui assure la mise à la terre pour votre
sécurité. Si la prise fournie ne convient pas à la prise
murale dont vous disposez, consultez un électricien
pour remplacer et adapter votre prise murale.
10. Protégez le cordon d’alimentation pour éviter
de marcher dessus ou de le pincer particulièrement
aux endroits des prises, mâles et femelles, et au point
de raccordement sur l’appareil lui-même.
11. Utilisez uniquement des accessoires ou
options recommandés par le fabricant.
12. Utilisez uniquement un meuble
sur roulettes, un support, un pied, une
étagère ou une table de type recom-
mandé par le fabricant. Si vous utilisez un
meuble sur roulettes, veillez à le déplacer
avec précaution afin d’éviter tout acci-
dent corporel si l’équipement se renver-
sait.
13. Débranchez l’appareil pendant les orages ou s’il
doit rester inutilisé pendant une période de temps
prolongée.
14. Pour toute réparation, faites appel à un personnel
qualifié. Une réparation sera nécessaire si l’appareil a
subi des dommages tels que détérioration du cordon
d’alimentation ou de la prise, liquide renversé sur l’ap-
pareil, ou encore si un objet est tombé dessus, si l’ap-
pareil a été exposé à la pluie ou à l’humidité, s’il ne
fonctionne pas correctement ou s’il a fait une chute.
15. PRÉCAUTION d’emploi des piles – Afin d’éviter
toute fuite des piles qui risquerait de causer des
blessures corporelles, des dommages matériels, ou
d’endommager l’appareil :
● Installez toutes les piles correctement, + et - tels
qu’indiqués sur l’appareil.
● Ne mélangez pas les piles (pas de piles neuves avec
des usagées ou de piles au carbone avec des alca-
lines, etc.).
● Enlevez les piles lorsque l’appareil reste inutilisé pen-
dant une longue période.
EL 6475-F003: 02/8
CONSIGNES DE SÉCURITÉ IMPORTANTES
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
PHILIPS CONSUMER ELECTRONICS NORTH AMERICA
Knoxville, Tennessee 37914-1810, U.S.A.
AZ 2555 AZ 2555 CD Soundmachine
Need help? Call us!
Philips representatives are ready to help you with
any questions about your new product. We can guide you
through Connections, First-time Setup, or any of the Features.
We want you to start enjoying your new product right away!
CALL US BEFORE YOU CONSIDER
RETURNING THE PRODUCT!
1-800-531-0039
or
Visit us on the web at www.philips.com
S EE W HY INS ID E
IM
PO RTAN T ! Return your Warranty
Registration Card within 10 days
Printed in China
W
CLASS 1
LASER PRODUCT
AZ 2555
3140 115 3015.2
English
F ran
ç ais
Espa
ñ ol
AC Polarized
Plug
Prise
polarisée C.A.
English:This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference Regulations of the
Canadian Department of Communications.
Français: Cet appareil numérique n'émet pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de Classe B prescrites dans le Règlement sur
le Brouillage Radioélectrique édicté par le Ministère des Communications du Canada.
Canada
Clavija polarizada de CA
Meet Philips at the Internet
http://www.philips.com
PORTABLE AUDIO
One Year Free Exchange
This product must be carried in for an exchange.
LIMITED WARRANTY
WHO IS COVERED?
You must have proof of purchase to exchange the product.
A sales receipt or other document showing that you pur-
chased the product is considered proof of purchase. Attach
it to this owner’s manual and keep both nearby.
WHAT IS COVERED?
Warranty coverage begins the day you buy your product.
For one year thereafter, a defective or inoperative product
will be replaced with a new, renewed or comparable prod-
uct at no charge to you. A replacement product is covered
only for the original warranty period.When the warranty
on the original product expires, the warranty on the
replacement product also expires.
WHAT IS EXCLUDED?
Your warranty does not cover:
•
labor charges for installation or setup of the product,
adjustment of customer controls on the product, and
installation or repair of antenna systems outside of the
product.
• product repair and/or part replacement because of
misuse, accident, unauthorized repair or other cause
not within the control of Philips.
• reception problems caused by signal conditions or
cable or antenna systems outside the unit.
• a product that requires modification or adaptation to
enable it to operate in any country other than the
country for which it was designed, manufactured,
approved and/or authorized, or repair of products
damaged by these modifications.
• incidental or consequential damages resulting from the
product. (Some states do not allow the exclusion of
incidental or consequential damages, so the above
exclusion may not apply to you.This includes, but is not
limited to, prerecorded material, whether copyrighted
or not copyrighted.)
• a product used for commercial or institutional purposes.
WHERE IS EXCHANGE AVAILABLE?
You may exchange the product in all countries where the
product is officially distributed by Philips. In countries
where Philips does not distribute the product, the local
Philips service organization will attempt to provide a
replacement product (although there may be a delay if the
appropriate product is not readily available).
BEFORE REQUESTING EXCHANGE...
Please check your owner's manual for assistance. If you
have additional questions, call us at 1-800-531-0039.
EXCHANGING A PRODUCT IN U.S.A.,
PUERTO RICO, OR U.S.VIRGIN ISLANDS...
Contact 1-800-531-0039 to arrange an exchange. Or, ship
the product, insured and freight prepaid, and with proof of
purchase enclosed, to the address listed below.
Philips Exchange Program Suite A 406 North Irish Street
Greeneville TN 37745
(In U.S.A., Puerto Rico, and U.S.Virgin Islands, all implied war-
ranties, including implied warranties of merchantability and fit-
ness for a particular purpose, are limited in duration to the
duration of this express warranty. But, because some states do
not allow limitations on how long an implied warranty may
last, this limitation may not apply to you.)
EXCHANGING A PRODUCT IN CANADA...
Please contact Philips at:
1-800-661-6162 (French Speaking) 1-800-531-0039 (English or Spanish Speaking)
(In Canada, this warranty is given in lieu of all other war-
ranties. No other warranties are expressed or implied,
including any implied warranties of merchantability or fit-
ness for a particular purpose. Philips is not liable under any
circumstances for any direct, indirect, special, incidental or
consequential damages, howsoever incurred, even if notified
of the possibility of such damages.)
REMEMBER...
Please record below the model and serial numbers found
on the product. Also, please fill out and mail your warranty
registration card promptly. It will be easier for us to notify
you if necessary.
MODEL # __________________________________
SERIAL # __________________________________
EL6095T004 / 8-02
This warranty gives you specific legal rights.You may have other rights which vary from state/province to state/province.
Philips, P.O. Box 520890, Miami, FL 33152, USA, (402) 536-4171
3. EQUALIZER
To adjust the bass, mid and treble frequencies press
EQUALIZER once or more, then rotate VOLUME
within 3 seconds to adjust each level.
=Display briefly shows , , or
level (-5 to +5) or .
Note: EQUALIZER can be used during TUNER, CD,
USB PC LINK and GAME•AUX source.
4. GAMESOUND
To adjust the game sound, press GAMESOUND once
or more to select your option.
=Display briefly shows , ,
or .
Note: GAMESOUND is only available when you
play in GAME•AUX source.
How to MUTE the sound
1. Press MUTE on the remote control to interrupt
sound reproduction instantly.
= Playback continues without sound and the
display flashes .
2. To reactivate sound reproduction you can:
– press MUTE again;
– adjust the volume controls;
– press
2; / 9 in CD / USB PC LINK source;
– change to another source.
DIGITAL TUNER (See 3)
Tuning to stations
1. Press STANDBY ON y to on, then press
SOURCE once or more to select TUNER (or press
TUNER once on the remote control).
= Display: shows
briefly followed by
waveband, frequency, and preset station
number if already stored.
2. Press FM•AM once or more to select your
waveband. (TUNER on the remote control)
3. Tuning to stations: you can tune to your
stations manually or by automatic search tuning:
Press down on
∞ or §I and release button when
the frequency in the display starts running.
= The radio automatically tunes to a station of
sufficient reception. Display shows
during automatic tuning.
4. Repeat step 3 if necessary until you find the
desired station.
• To tune to a weak station, press ∞ or § briefly
and repeatedly until you have found optimal
reception.
To improve radio reception:
• For FM, extend, incline and turn the telescopic
antenna. Reduce its length if the signal is too
strong.
• For AM, the set uses a built-in antenna. Direct this
antenna by turning the whole set.
Programming tuner stations:
You can store up to a total of 30 radio stations in the
memory, manually or automatically (Autostore).
Autostore
Automatic programming will start from preset 1 or a
chosen preset number. From this preset number
upwards, former programmed tuner stations will be
erased. The set will only program stations which are
not in the memory already.
1. Press PRESET- or + once or more to select the
preset number where programming should start.
Note: If no tuner preset number is selected, default
is preset 1 and all your presets will be erased.
2. Press PROG for 4 seconds or more to activate
auto store programming.
= Display:
is shown and available
stations are programmed in order of waveband
FM, followed by AM , the first preset station
will then be played after all stations are stored
automatically.
Manual programming
1. Tune to your desired station (see Tuning to
stations).
2. Press PROG to activate programming.
= Display: PROG flashes.
3. Press PRESET - /+ once or more to allocate a
number from 1 to 30 to this station.
4. Press PROG again to confirm.
= Display: shows the preset number, waveband
and the frequency of the preset station.
5. Launch MUSICMATCH JUKEBOX and create
your own playlist of favorite songs by dragging and
dropping the music track from anywhere on your PC
into the playlist window.
Note:
-- If you encounter any problem using the USB PC LINK,
please refer to the FAQ (Frequently Asked Questions)
stored in your USB PC LINK installer disc or visit
www.audio.philips.com for the latest FAQ updates .
After setup, refer to "Connecting to USB PC Link"
for details on the USB PC LINK operations.
Enable digital CD audio output
Before playing CDs on your PC’s CD-ROM drive, it is
necessary to configure your PC’s hardware as follows:
For Windows ME/ 2000/ XP
1. Enter the system panel menu and select
'SYSTEM', 'PROPERTIES', 'HARDWARE',
'DEVICE MANAGER', 'CD-ROM DRIVES' and
'PROPERTIES'.
For Windows 98
2. Check the Enable digital CD audio for this CD-
ROM device setting option is selected (enabled).
Note:-For windows 98 you may need to refer to
your PC's manual for correct configuration.
Connecting to USB PC Link (See 9)
The USB PC LINK allows you to playback your music col-
lection from the PC via the powerful amplifier and speak-
ers of this system.
IMPORTANT!
Make sure the MusicMatch software has been
installed. Refer to "Quick Setup Guide" for the
USB PC Link.
1. Turn on your set and computer .
] Check your PC volume is suitably adjusted and
not set to minimum / mute.
2. Press SOURCE (USB on the remote control) once
or more to select USB PC LINK .
3. If correctly connected your PC will automatically
launch MUSICMATCH JUKEBOX.
] If the audio streaming is detected, the current
track name scrolls .
]If scrolls for a while, check the
connection between your PC and set.
4. Press ¡ or ™ until the desired track in the playlist is
highlighted.
5. Press 2; to start playback.
] The track time appears and the track name scrolls
once.
Note: The display only supports English characters
in uppercase.
6. If you want to see the track details displayed press
MODE.
During playback,
– Press SHUFFLE on the remote control to play all
available tracks in the playlist in random order.
– Press REPEAT on the remote control to repeat
playback all the tracks in the playlist.
7. To cancel play modes/ stop playback, press 9 or
select another sound sources.
MAINTENANCE & SAFETY (See 0)
CD player and disc handling
• If the CD player cannot read CDs correctly, use a
cleaning CD to clean the lens before taking the set to
repair.
• The lens of the CD player should never be touched!
• Sudden changes in the surrounding temperature can
cause condensation on the lens of your CD player.
Playing a CD is then not possible. Do not attempt to
clean the lens but leave the set in a warm
environment until the moisture evaporates.
• Always close the CD door to avoid dust on the lens.
• To take a CD out of its box, press the center spindle
while lifting the CD.
• To clean the CD, wipe in a straight line from the center
towards the edge using a soft, lint-free cloth. Do not
use cleaning agents as they may damage the disc.
• Never write on a CD or attach any stickers to it.
Safety Information
• Don't expose the set, batteries, CDs to humidity, rain,
sand or excessive heat.
• Clean the set with a dry cloth. Don't use any
cleaning agents containing alcohol, ammonia,
benzene or abrasives as these may harm the set.
• Place the set on a hard and flat surface so that the
system does not tilt. Make sure there is good
ventilation to prevent the set from overheating.
USB PC LINK MAINTENANCE & SAFETY
5. Repeat the above four steps to store other
stations.
Note : You can erase a preset station by storing
another frequency in its place.
To listen to a preset station
Press PRESET - / + once or more until the desired
preset station is displayed.
CD Operation
Playing a CD
This CD player plays Audio Discs including
CD-Recordables and CD-Rewritables.
1. Press STANDBY ON y once or more to on, then
select CD SOURCE.
2. Press OPEN•CLOSE to open the CD door.
] is displayed when the CD door is
open.
3. Insert a CD with the printed side facing up and press
down on OPEN•CLOSE to close the CD door.
]Display show
, then scrolls
, or
if no CD inserted/ CD dirty,
incorrectly inserted or damaged.
4. Press 2; to start playback.
5. To pause playback press 2;. Press 2; again to
resume play.
= Time digits flashes during pause.
6. To stop CD playback, press 9.
Note: CD play will also stop when:
– the CD door is opened
– the CD has reached the end
– you select an other sound source.
Selecting a different track
• Press SEARCH ∞ or § (on the remote control ¡
or ™) once or repeatedly until the desired track
number appears in the display.
• If you have selected a track number shortly after
loading a disc or in the PAUSE position, you will
need to press
2; to start playback.
Finding a passage within a track
1. Press and hold SEARCH ∞ or §.
– The CD is played at high speed and low volume.
2. When you recognize the passage you want,
release ∞ or §. Normal playback continues.
Note: During a CD program or if SHUFFLE/ REPEAT
is active, searching is only possible within the same
track.
Different play modes: SHUFFLE and REPEAT (See
4 - 7)
You can select and change the various play modes
before or during playback. The play modes can also be
combined with PROGRAM.
SHUFFLE - tracks of the entire CD/ program are
played in random order
SHUFFLE REPEAT ALL - to repeat the entire CD/
program continuously in random order
REPEAT ALL - repeats the entire CD/ program
REPEAT - plays the current track continuously
1. To select play mode, press MODE once or more.
(SHUFFLE / REPEAT on the remote control).
2. Press 2; to start playback if in the stop position.
]If you have selected SHUFFLE, playback starts
automatically.
3. To select normal playback, press MODE
repeatedly until the various modes are no longer
displayed.
– You can also press the
9 to cancel your play
mode in playing.
Programming track numbers
Program in the stop position to select and store your
CD tracks in the desired sequence. If you like, store
any track more than once. Up to 20 tracks can be
stored in the memory.
1. Press SEARCH
∞ or § on the set to select your
desired track number.
2. Press PROG to confirm the track number to be
stored.
=Display: The number of the tracks programmed
and the total playing time of programmed tracks
SUPPLIED ACCESSORIES
– remote control
– USB cable
– video cable
– CD-ROM USB PC LINK installers
TOP AND FRONT PANEL (See 1)
1 p - 3.5 mm stereo headphone jack.
Note: The speakers will be muted when headphones
are connected to the set.
2 VOLUME -adjust volume level or equalizer level
(BASS/ MID /HIGH)
3 STANDBY ON y - switch the set on/ off.
4 SOURCE - selects sound source for functions: CD/
TUNER/ USB PC LINK/ GAME •AUX
5 IR SENSOR -infrared sensor for remote control
6 LCD Display - shows the status of the set
7 [dB]: - display to indicate bass power.
8 PRESET
-, + - selects a preset radio station.
SEARCH ∞ , §
CD: - searches backward or forward within a track;
- skips to the beginning of a current track/ previous/
later track.
USB PC LINK - skips to the beginning of a previous/
later track.
TUNER: - tunes to radio stations
2;- starts or pauses CD / USB PC LINK playback
9 - stop CD / USB PC LINK playback;
- erases a CD program.
MODE - selects different CD play modes: e.g.
REPEAT or SHUFFLE order.
- shows current track name in USB PC
LINK mode
9 USB - connect the supplied USB cable here to the
USB port of your computer
0 GAMESOUND - select sound effects: BLAST/
PUNCH/ SPEED/ NORMAL in GAME •AUX mode
WOOX - selects special bass enhancement on/ off
EQUALIZER - selects bass, mid and treble
frequencies, and volume BASS/ MID /HIGH/ VOL
PROG
CD: - programs tracks and reviews the
programmed songs;
TUNER: - programs preset radio stations.
FM•AM - selects FM / AM waveband
! AUDIO IN ( LEFT / RIGHT) - LINE-IN jack for
external audio appliance.
VIDEO IN - to keep video plug in place
@ OPEN•CLOSE – press to open/ close CD door
BACK PANEL (See 1)
# Telescopic antenna - improved FM reception
$ Battery compartment - for 8 batteries, type
R-20, UM-1 or D-cells
% AC MAINS - inlet for power cord
^ VIDEO OUT- connect to the VIDEO IN jack on a
TV or VCR for viewing or recording.
REMOTE CONTROL (See 1)
1 CD - selects CD sound source
TUNER - selects tuner source / wavebands
USB - selects USB PC LINK
AUX - selects GAME •AUX
2 y -switches the set to standby / on if set
operating on AC power. (Switches set off only if
battery powered)
3 REPEAT - repeat all tracks in USB PC LINK source
or selects the repeat modes in CD source
SHUFFLE - plays CD tracks in random order in CD /
USB PC LINK source
MUTE - interrupts/ resumes sound
4 VOL 4, 3 -- adjust volume level or adjust equalizer
level (BASS/ MID /HIGH)
5 ¡ , ™ - select previous/ next track in CD / USB PC
LINK playback
9 - stop CD / USB PC LINK playback;
- erases a CD program.
2; - starts or pauses CD or USB PC LINK playback
5 / 6 - searches backwards/ forwards within a CD
track.
TUNER: - tunes to radio stations
6 EQUALIZER -- selects bass, mid and treble
frequencies
WOOX -- select special bass enhancement on/ off
GAMESOUND - select sound effects: BLAST/
PUNCH/ SPEED/ NORMAL in game mode
7 PRESET -, + , - selects a previous/ next radio
preset station
CAUTION
Use of controls or adjustments or performance
of procedures other than herein may result in
hazardous radiation exposure or other unsafe
operation.
POWER SUPPLY
Whenever convenient, use the power supply to
conserve battery life. Make sure you remove the
power cord from the set and wall jack before inserting
batteries.
Batteries (not included) (See 1)
• Insert 8 batteries, type R-20, UM-1 or D-cells,
(preferably alkaline) with the correct polarity.
Remote control (See A)
• Insert 2 batteries, type AAA, R03 or UM4
(preferably alkaline).
Incorrect use of batteries can cause electrolyte leak-
age and will corrode the compartment or cause the
batteries to burst.
• Do not mix battery types: e.g. alkaline with carbon
zinc. Only use batteries of the same type for the
set.
• When inserting new batteries, do not try to mix old
batteries with the new ones.
• Batteries contain chemical substances, so
they should be disposed of properly.
Using AC Power
1. Check if the AC power supply, as shown on the
type plate located on the bottom of the set,
corresponds to your local power supply. If it does
not, consult your dealer or service center.
2. If your set is equipped with a voltage selector,
adjust the selector so that it matches with the
local power supply.
3. Connect the power cord to the wall jack and the
set is now ready for use.
4. To disconnect the power supply, unplug the set
from the wall jack.
POWER-SAVING AUTOMATIC STANDBY
As a power-saving feature, the system automatically
switches to standby 15 minutes after CD has reached
the end and no control is operated.
The type plate is located on the bottom of
the set.
BASIC FUNCTIONS
Switching on and off and selecting function
1. Press STANDBY ON y on the set to switch on.
2. Press SOURCE once or more to select your
desired function: CD, TUNER, USB PC LINK or
GAME•AUX .
3. Press STANDBY ON y to switch off the set.
Note : The tone, sound settings, tuner presets and
the volume level (up to a maximum volume level of
VOL 20 ) will be retained in the set's memory.
Adjusting volume and sound (See 2)
1. Adjust the volume with the VOLUME control.
= Display shows the volume level and a
number from 0-32.
2. wOOx
To enhance the bass response: press wOOx once or
more to switch on / off.
= wOOx-key backlight lights up when wOOx is
turned on.
Notes:
- wOOx can be used when you play TUNER, CD, USB
PC LINK and GAME•AUX source.
- To prevent sound interference the bass control
options operate exclusively. You cannot combine the
bass from EQUALIZER with wOOx
- Some discs might be recorded in high modulation,
which causes a distortion at high volume. If this
occurs, deactivate wOOx or reduce the volume.
English CONTROL
is shown briefly PROG flashes.
=If you attempt to program without first selecting
a track number, is shown.
3. Repeat steps 1-2 to select and store all desired
tracks.
=Display:
if you try to program more
than 20 tracks.
4. To start playback of your disc program, press 2; .
Note: During normal playback, you can press PROG
to add a current track to your program list.
Reviewing the program
In stop / play position, press and hold down PROG for
a while until the display shows all your stored track
numbers in sequence.
Erasing a program
You can erase the program by:
• pressing
9 twice;
= displayed briefly, and PROG
disappears.
• pressing STANDBY ON y
• selecting another sound sources
• opening the CD door.
GAMESOUND (See 8)
PLAYING WITH GAMESOUND:
1. Press SOURCE once or more on the set to select
the GAME•AUX function (AUX on the remote
control)
=Display scrolls :
2. Connect your console to the cinches on the front
of the set AUDIO IN ( LEFT / RIGHT) and VIDEO
IN.
3. Press GAMESOUND once or more to select your
game sound option.
=Display briefly shows
, ,
or .
Connecting other equipment to your system
Use the supplied video cable to connect the VIDEO
OUT terminal on the back of the set to VIDEO IN on
a TV or VCR for viewing or recording.
USB PC LINK
Quick Setup Guide
PC system requirements
– USB port with Windows 98 / 98 SE / ME/ 2000/ XP
– Intel Pentium MMXX200 or higher
– CD-ROM drive
– Free hard disk space : 15 MB for the software
Installing MusicMatch software
1. Use the supplied USB cable to connect the set to the
USB port on your computer. (See B)
2. Press SOURCE (USB on the remote control) once or
more to select USB PC LINK.
3. Turn on your PC then insert the supplied USB PC LINK
installer disc in the PC's CD-ROM drive. This
application software can also be downloaded from
http://www.audio.philips.com.
IMPORTANT!
Please use this customized MusicMatch
software for your USB PC Link application.
Remember to un-install all other MusicMatch
jukebox software first from your PC system (if
available).
4. The installation guide will appear automatically. If it
does not, go to the CD-ROM drive in Windows
Explorer and double click on the USB PC LINK.exe.
Then perform the following steps:
– Select your desired language from the list.
– Select installer driver.
– Select installer MusicMatch jukebox.
– Select other options (Tutorial, Free goodies, FAQ).
Note:
- You are advised to read the MusicMatch tutorial
before using it for the first time. Make sure the
volume on your PC is suitably adjusted to ensure
sound output on the set. For optimum performance,
the equalizer function in MusicMatch should be set to
a low level.
CD PLAYER CD PLAYER GAMESOUND USB PC LINK
TROUBLESHOOTING
POWER SUPPLY BASIC FUNCTIONS DIGITAL TUNER DIGITAL TUNER
No sound /power
– Volume not adjusted
• Adjust the VOLUME
– Power cord not securely connected
• Connect the AC power cord properly
– Batteries flat / incorrectly inserted
• Insert (fresh) batteries correctly
– Headphones connected to the set
• Disconnect headphones
– Electrostatic discharge/interference
• Unplug the set. If batteries inserted, remove batteries
from the battery compartment.. Press and hold
STANDBY ON y for 10 seconds, then re-plug /
replace battery supply, and try activating the set again.
• When in USB PC LINK mode, check that your PC's
volume is audible and not set to minimum.
• When playing a CD from the PC's CD-ROM drive, refer
to USB PC Link - Enable digital CD audio output.
Severe radio hum or noise
– Electrical interference: set too close to TV, VCR or
computer
• Increase the distance
Remote control does not function properly
– Batteries flat/ incorrectly inserted
• Insert (fresh) batteries correctly
– Distance/ angle between the set too large
• Reduce the distance/ angle
Poor radio reception
– Weak radio signal
• FM: Adjust the FM telescopic antenna
indication
– No CD inserted
• Insert a suitable disc
– CD badly scratched or dirty
• Replace/ clean CD, see Maintenance
– Laser lens steamed up
• Wait until lens has cleared
The CD skips tracks
– CD damaged or dirty
• Replace or clean CD
– SHUFFLE or PROG is active
• Switch off SHUFFLE / PROG
is displayed in USB PC LINK
mode for more than 10 sconds
• Check the connection between your PC and the set. If
necessary, please refer to the chapter Connecting to
USB PC Link for the initial setup required.
• Make sure the connected PC is turned on and the
MusicMatch software is working.
3
5
6
7
8
9
0 !
#
$
^ %
1
2
4
@
8 x R20/ UM1/ D CELL
2
1
7
5
3
4
5
6
4
3
Take care of your CD Soundmachine.
Grip both handles when you carry or
lift the set.
HEAVY !
1
SISTEMA DE AUDIO PORTATIL
Cambio gratis por un año
Se necesita presentarse en persona con este producto para cambiarlo.
GARANTIA LIMITADA
¿QUIEN TIENE PROTECCION?
Usted debe tener su comprobante de venta para cambiar el
producto. Una nota de venta u otro documento mostrando
que usted compró el producto se considera un comprobante
de venta.Adjúntelo a este manual de instrucciones y reténgalo
a la mano.
¿QUE CUBRE?
La protección bajo la garantía comienza el mismo día en que
usted compra el producto. Durante un año a partir de esta
fecha, se reemplazará un producto inoperante o defectuoso
con otro nuevo, renovado o comparable sin cargo alguno. Un
producto de reemplazo tiene cobertura sólo durante el
período de la garantía original. Una vez que venza la garantía
original del producto, también habrá vencido la garantía del
producto de reemplazo.
¿QUE EXCLUYE LA GARANTIA?
Su garantía no cubre:
• cobros por mano de obra durante la instalación o montaje
del producto, ajuste de los controles del cliente o de
preferencia e instalación o reparación de los sistemas con
antena fuera de la unidad.
• reparación del producto y/o reemplazo de piezas, a raíz
de uso indebido, accidente, reparación no autorizada u
otra causa no bajo el control de Philips.
• problemas de recepción ocasionados por condiciones de
señales o sistemas de cable o de antena fuera de la
unidad.
• un producto que requiera modificación o adaptación para
que opere en un país que no sea el país para el que fue
concebido, fabricado, aprobado y/o autorizado, o la
reparación de productos dañados por tales modificaciones.
• daños incidentales o consecuentes que resulten del
producto. (Algunos estados no permiten la exclusión por
daños incidentales o consecuentes, de modo que es posible
que la exclusión arriba indicada no le sea aplicable a usted.
Esto incluye, sin limitarse, materiales pregrabados con o sin
amparo de derechos de autor.)
• una unidad que se ha usado para fines comerciales o
institucionales.
¿DONDE SE EFECTUA EL CAMBIO?
Usted puede cambiar el producto en todos los países con
distribución oficial del producto por Philips. En países
donde Philips no distribuye el producto, la entidad local de
servicio Philips tratará de darle un producto de reemplazo
(aunque puede haber demora si el producto apropiado no
está fácilmente disponible).
ANTES DE PEDIR UN CAMBIO…
Por favor, consulte su manual del usuario si necesita ayuda.
Si tiene más preguntas, llámenos al 1-800-531-0039.
PARA CAMBIAR UN PRODUCTO EN LOS
EE.UU., PUERTO RICO O LAS ISLAS VIRGENES…
Contacte con el 1-800-531-0039 para concertar un cambio.
También, usted puede enviar el producto con el seguro y
transporte o franqueo prepagados, adjuntando el comprobante
de venta y enviándolo a la dirección a continuación:
Philips Exchange Program Suite A
406 North Irish Street
Greeneville TN 37745
(En los EE.UU., Puerto Rico o las Islas Vírgenes, toda garantía
implícita, inclusive las garantías implícitas de comerciabilidad y
aptitud para un propósito en particular, están limitadas en
cuanto a duración al plazo de esta garantía expresa. Puesto
que algunos estados no permiten limitaciones sobre la
duración de una garantía implícita, es posible que la limitación
arriba indicada no le sea aplicable a usted.)
PARA CAMBIAR UN PRODUCTO EN EL
CANADA…
Favor de comunicarse con Philips al:
1-800-661-6162 (francófono) 1-800-531-0039 (anglófono o hispanohablante)
(En el Canadá, esta garantía es otorgada en lugar de toda
otra garantía. No se otorga ninguna otra garantía expresa ni
implícita, comprendiéndose aquí ninguna garantía implícita
de comerciabilidad o aptitud para propósito alguno. Philips
no será responsable bajo circunstancia alguna por daños y
perjuicios directos, indirectos, especiales, incidentales o
consecuentes, independientemente de la manera ocasionada,
aún con notificación de la posibilidad de los mismos.)
RECUERDE…
Favor de anotar los números de modelo y serie del
producto en el espacio abajo.También, sírvase llenar y
enviar oportunamente su tarjeta de registro de la garantía.
Así nos será más fácil notificarle en caso de ser necesario.
Modelo No. ________________________________
Serie No. ________________________________
EL6095T004 / 8-02
Esta garantía le otorga derechos legales específicos y usted podría gozar de otros derechos que varían de un estado a otro.
Philips, P.O. Box 520890, Miami, FL 33152, USA,(402) 536-4171
SYSTÈME SONORE PORTABLE
Échange gratuite pendant un an
Il faut porter ce produit à un centre de service pour l’échanger.
GARANTIE LIMITÉE
QUI EST COUVERT ?
Il faudra présenter une preuve d’achat pour pouvoir
bénéficier des services de la garantie. Le reçu, la facture ou
un autre document portant la date d’achat qui prouve que
vous avez bien acheté le produit est considéré comme
preuve d’achat. L’attacher à ce manuel d’emploi et les
garder tous les deux à portée de main.
QU’EST-CE QUI EST COUVERT ?
La couverture de la garantie entre en vigueur le jour où
vous achetez le produit. Pendant un an à compter de cette
date, tout produit défectueux ou qui ne fonctionne pas
sera remplacé par un produit neuf, renouvelé ou un produit
comparable sans frais aucun au consommateur. Un produit
de remplacement n’est couvert que pendant la période
non-écoulée de garantie d’origine. Lorsque la garantie du
produit d’origine vient à terme, la garantie du produit de
remplacement est terminée aussi.
QU’EST-CE QUI EST EXCLU DE LA GARANTIE ?
La garantie ne couvre pas :
• les frais de main d’œuvre pour installer ou préparer,
pour régler les commandes et pour installer ou réparer
les systèmes d’antenne à l’extérieur du produit.
• la réparation du produit et/ou d’une pièce pour cause du mauvais emploi, d’accident, de réparations non-agréées
ou d’une autre raison qui ne peut pas être contrôlée par
Philips.
• des problèmes de réception dыs а des conditions de signal, au câble ou aux systèmes d’antenne à l’extérieur de l’unité.
• un produit qui nécessite des modifications ou adaptations pour lui permettre de fonctionner dans un pays autre que
le pays pour lequel il a été conçu, fabriqué, agréé et/ou
autorisé, ou la réparation des produits endommagés par
de telles modifications.
• des dommages indirects ou conséquents qui résultent du produit. (Certains états ou provinces ne permettent pas
l’exclusion de dommages indirects ou conséquents. Il est
donc possible que l’exclusion ci-dessus ne s’applique pas au
cas présent. Cela comprend, mais de façon non-limitative,
des enregistrements, qu’ils soient protégés ou non par les
lois sur les droits d’auteur).
• un produit utilisé pour des raisons commerciales ou institutionnelles.
OÙ L’ÉCHANGE EST-ELLE PROPOSÉE ?
Le produit pourra s’échanger dans tous les pays où le produit
est distribué officiellement par Philips. Dans des pays où
Philips ne distribue pas le produit, l’organisme local de service
Philips tentera de fournir un produit de remplacement (mais
il pourra y avoir des retards si le bon produit n’est pas
facilement disponible).
AVANT DE DEMANDER UNE ÉCHANGE…
Veuillez consulter votre guide d'utilisation pour assistance.
Si vous avez d'autres questions, contactez-nous au
1-800-531-0039.
POUR BÉNÉFICIER DE L’ÉCHANGE GARANTIE
AUX É.-U., AU PUERTO RICO OU DANS LES
ÎLES VIERGES AMÉRICAINES…
Contactez 1-800-531-0039 pour organiser un échange.
Ou bien, renvoyer le produit, frêt et assurances payés, avec
preuve d’achat incluse, à l’adresse ci-dessous :
Philips Exchange Program
Suite A 406 North Irish Street
Greeneville TN 37745
(Aux É.-U., au Puerto Rico et aux Îles Vierges, toute garantie
implicite, y compris des garanties de vendabilité et d’aptitude
à un but spécifique, est limitée à la durée de cette garantie
explicite. Mais, étant donné que certains états et provinces
ne permettent pas de limité la durée d’une garantie implicite,
cette limitation pourrait ne pas s’appliquer au cas présent.)
POUR BÉNÉFICIER D’UNE ÉCHANGE GARANTIE
AU CANADA…
Veuillez contacter Philips au :
1-800-661-6162 (Francophone) 1-800-531-0039 (Anglophone ou hispanophone)
(Au Canada, cette garantie est consentie à la place de toute
autre garantie.Aucune autre garantie n’est donnée, qu’elle
soit explicite ou implicite, y compris une garantie implicite
de vendabilité ou d’aptitude à un but spécifique. Philips n’est
pas, en aucun cas, responsable des dommages, qu’ils soit
directs ou indirects, spéciaux, secondaires ou conséquents,
quels que soient leurs origines, même en présence d’une
notification de la possibilité de tels dommages.)
RAPPEL IMPORTANT...
Veuillez inscrire ci-dessous les numéros de modèle et de
série qui se trouvent sur le produit même. De plus, veuillez
remplir et renvoyer sans délai la carte d’enregistrement de
garantie. Il nous sera ainsi plus facile de vous contacter en
cas de besoin.
Nº DE MODÈLE _____________________________
Nº DE SÉRIE _____________________________
EL6095T004 / 8-02
Cette garantie vous donne des droits légaux spécifiques et vous pourriez avoir d’autres droits qui varient d’état en état et de province en province.
Philips, P.O. Box 520890, Miami, FL 33152, É.-U.,(402) 536-4171
2 x AAA
2
3
4
5
A
X
0
6
8
9
USB
B
If a fault occurs, first check the points listed below before taking the set for repair. If you are
unable to remedy a problem by following these hints, consult your dealer or service center.
WARNING: Do not open the set as there is a risk of electric shock! Under no
circumstances should you try to repair the set yourself, as this will
invalidate the warranty.
7
Note : This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures :
– Relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
The set complies with the FCC-Rules, Part 15 and with 21 CFR 1040.10.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation.
IMPORTANT :
Modifications not authorized by the manufacturer may void users authority to
operate this device.
az2555/17 20/2/03 16:33 Page 1