AeroBed FInstant On Hand-Held AC Pump Model 103H - Manuel

DEFLATION AND STORAGE
1. Open the Quick Air Release Valve cover at the head of the bed to release the air.
2. Fold sides of bed into the center along its length. Tightly roll your bed towards the Quick Air Release Valve at the end of the bed.
3. Roll the bed completely until all air is expelled. When the bed is completely rolled, push the Quick Air Release Valve closed and lock for its next use.
4. Slide the duffel bag over your AeroBed. Store your bed and pump until its next use.
CARE AND MAINTENANCE
1. Inspect your bed prior to each use.
2. Keep your bed away from any sharp objects or obstacles with rough edges. Large cuts or snags may not be repairable and will not be covered by your bed warranty.
3. When not in use, store your bed in a clean, dry place out of extreme temperatures. Note: Bed must be at room temperature prior to inflating or it may cause air leaks.
4. In case of incidental damage to your bed, a repair patch has been included. Please follow repair instructions carefully.
Thank you for joining the AeroBed ® family by purchasing one of our upscale products. You can expect top-notch quality, innovation, and imagination from every AeroBed product.
You are about to enjoy the comfort of an AeroBed product. It is your responsibility to read and always follow the safety, care, and maintenance instructions for your new AeroBed
product. Always instruct and supervise others on your bed’s proper use, maintenance, and safety.
IMPORTANT: Preparation of your AeroBed product requires no tools. Use of tools may damage your bed.
7978CF Rev 07/07
Pump 103H/DV Instruction Manual
IMPORTANT SAFETY INFORMATION AND WARNINGS
WARNING: Adult supervision required for inflation, deflation, and maintenance. This is not a lifesaving device. Do not leave children unattended in or around water.
WARNING: This bed is not designed for use by children under 3 years of age. Children under the age of 3 may suffer serious or fatal injury through suffocation, falling from the
bed or becoming trapped between the bed and a wall or other objects.
WARNING: Product is for indoor use only.
WARNING: For household / residential use only.
- This is not a water toy. Use as a mattress only.
- This mattress is not intended for infants or persons with limited mobility. They may roll off of the mattress and become entrapped between the mattress and a wall.
- Do not use this bed on abrasive surfaces or near pointed/sharp items or surfaces. Protruding objects may puncture bed. Remove all sharp objects from area where bed will be
set up and used.
- Do not step or jump on bed or use as a trampoline. Bed may puncture.
- Place bed in a safe area before use, making sure that there are no sharp edges, steps, drops, or breakable items nearby. Use on flat surfaces only.
Bed may tip over on uneven surfaces.
- Standing, jumping, or walking on the bed may result in injury and/or damage the bed. Do not jump, stand, or walk on this bed. You can hurt yourself or damage the bed if you do.
- This bed is made of plastic and therefore may melt or burn if it comes in contact with any flame or heat source. Do not place it near or against heaters, open flame, or other hot
objects.
Pump
WARNING: This is an electrical product - not a toy. To avoid risk of fire, burns, injury, or shock, it should not be played with or placed where small children can reach it.
Do not use in or around water.
- Unplug product when not in use.
- Pump is an electrical device. Do not use in or around water. DO NOT place pump where it could fall or be pulled into the water.
- Pump not recommended for use by children under six (6) years of age.
- Do not attempt to disassemble, repair, or service the pump. No serviceable parts are contained inside. Contact Aero Products International, Inc.
at 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173, for repair or servicing information.
This is the closed position. Open Air Release Valve Close Valve Using 2 Thumbs
INFLATION
NOTE: BED MUST BE AT ROOM TEMPERATURE PRIOR TO INFLATING OR IT MAY CAUSE AIR LEAKS.
1. Place your rolled-up bed on the floor or other surface free of obstructions or sharp objects.
2. Make certain the Quick Release Valve located at the head of the bed is closed. If the Air Release Valve is open, close it by using 2 thumbs to push
cover and snap into valve. Be careful to avoid pushing valve cover to the right or left as it snaps into the valve opening.
3. Remove AC pump and cord from protective plastic shipping wraps.
4. Plug into any standard polarized 110 Volt AC electrical outlet. North American Electrical rating: 120 VAC 60HZ 1.0A (Note: 230VAC product
sold outside of North America). This product has a polarized attachment plug (one blade is wider than the other) as a safety feature. This plug
will fit into a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Never use with an extension cord unless the plug can be fully inserted. Do not attempt to defeat this safety feature.
5. Remove protective plastic cap from the Quick Air Release Valve by turning counter clockwise. Open the protective rubber cap at the end of the pump.
Press mouth of the pump into position on the Quick Air Release Valve and turn clockwise until it locks.
6. A one-quarter turn clockwise automatically starts inflation.
7. At approximately 60 seconds, a high pitch whine of the pump will signal the bed is inflated to full (firmest) capacity. Bed will not over-inflate.
8. Detach pump by turning counter clockwise. Lie on bed and check the firmness. If you want your bed to be softer, depress the botton in the center
of the valve. If the bed becomes too soft, reattach the pump and reinflate the bed until the desired level of firmness is achieved.
IMPORTANT: Be sure to close the protective cap after inflation.
Bed