Sony PRS-T1 - Manuel

Download new releases, best sellers, magazines and newspapers.
SHOP AT THE READER STORE
[Reader Store] application may be found on the Home screen. The initial
setting of the country/region of your Reader will determine if the Reader ™
Store is available in your area.
Tap [Reader Store] icon and follow the on-screen instructions to purchase
and download the content of your choice.
Purchased content is stored under either [Books] or [Periodicals] on the
Home screen.
Note
 The Reader Store image shown here may differ from the actual one.
Shop using your computer
(Where there is no access to a Wi-Fi network connection)
You can access the Reader Store from your computer.
Install either Reader ™ for PC or Reader ™ for Mac ® by launching the installer
on your Reader while it is connected to your computer by the supplied USB
cable and your Reader is set in data transfer mode.
An Internet connection is required to your computer.
Your personal content can be transferred onto your Reader via the Reader
software.
For details on how to install the software, refer to the User Guide.
Set up a Wi-Fi ® network connection with these simple steps.
JOIN A Wi-Fi ® NETWORK
Your Reader must be configured to connect to a Wi-Fi network for a
wireless Internet access.
INTERNET
INTERNET
The following questions will determine the most suitable case for setting
your Reader for a Wi-Fi network connection.
Case A
Case D
NO
1. Are you using a home Wi-Fi connection?
YES
YES
YES
Case C
NO
2. Is your Wi-Fi router WPS* compatible?
Case B
NO
3. Does your Wi-Fi router have a WPS button?
First, follow the COMMON INSTRUCTIONS below, then refer to your
case for further instructions.
COMMON INSTRUCTIONS
1. Tap [Wireless Network Settings] under [Settings] on the second page
of the [Home] screen on your Reader.
2. Confirm [Wi-Fi] has its check mark. Otherwise, turn on Wi-Fi by tapping
[Wi-Fi].
3. Tap [Wi-Fi Settings] to show the [Wi-Fi Settings] screen.
CASE A: A WPS-compatible Wi-Fi router with WPS button
Note: Make sure that your Reader shows the [Wi-Fi Settings] screen.
Otherwise, follow the steps under COMMON INSTRUCTIONS first.
1. Tap [WPS Push-Button Configuration].
2. Tap [Start].
3. Press the WPS button on your Wi-Fi router within 2 minutes.
4. After your Reader screen shows the setup completion, tap [OK].
CASE B: A WPS-compatible Wi-Fi router with PIN Input
Note: Make sure that your Reader shows the [Wi-Fi Settings] screen.
Otherwise, follow the steps under COMMON INSTRUCTIONS first.
1. Tap [Add Wi-Fi Network].
2. Tap [WPS PIN Method].
3. Tap [Start]. A PIN (Personal Identification Number) will be shown on the
screen of your Reader.
4. Enter the PIN into your Wi-Fi router. Please refer to your Wi-Fi router’s
instruction manual for further details.
5. After entering the PIN tap [OK]. Your Wi-Fi router’s SSID (Service Set
Identifier) appears in the [Wi-Fi Networks] list on the [Wi-Fi Settings]
screen.
6. Tap your Wi-Fi router’s SSID and tap [Connect].
CASE C: Connecting to a Wi-Fi router without WPS support
Note: Make sure that your Reader shows the [Wi-Fi Settings] screen.
Otherwise, follow the steps under COMMON INSTRUCTIONS first.
Check if the Wi-Fi router to be connected requires a password. A password
may also be called a WEP key/WPA key/encryption key/network key, or
similar.
1. Tap [Scan] to show a list of all available Wi-Fi networks.
2. Find and tap your Wi-Fi router’s SSID (Service Set Identifier) in the [Wi-
Fi Networks] list.
3. If prompted for a password, tap the input area and type in the
password using on-screen keyboard.
4. Tap [Connect].
CASE D: Connecting to an available Wi-Fi network
Note: Make sure that your Reader shows the [Wi-Fi Settings] screen.
Otherwise, follow the steps under COMMON INSTRUCTIONS first.
Check if the available Wi-Fi network requires a username and a password.
A password may be also called a WEP key/WPA key/encryption key/
network key, or similar.
1. Tap [Scan] to show a list of all available Wi-Fi networks.
2. Find and tap your Wi-Fi network SSID (Service Set Identifier) in the [Wi-
Fi Networks] list.
3. If prompted for a password, tap the input area and type in the
password using the on-screen keyboard.
4. Tap [Connect].
5. The [Browser] application may start automatically. Otherwise, start the
browser application manually; press the (Home) button, tap [ ] or
press the (Page Turn) button and tap [Browser].
6. The browser screen may show further information to complete the
connection. Follow any instruction(s) where applicable.
Manually setting a Wi-Fi connection
Note: Make sure that your Reader shows the [Wi-Fi Settings] screen.
Otherwise, follow the your Wi-Fi router’s COMMON INSTRUCTIONS first.
1. Tap [Add Wi-Fi Network].
2. Tap [Manual Registration].
3. Tap the [SSID] input area and type in using the on-screen keyboard.
4. Tap the [Security Method] menu (default value is [Open]) and tap the
supported security type.
5. Tap [Save].
6. Tap the saved network SSID in the [Wi-Fi Networks] list on the [Wi-Fi
Settings] screen.
7. If prompted for a password, tap the input area and type in the
password using the on-screen keyboard.
8. Tap [Connect].
MEET YOUR READER
microSD slot
Page Turn
Touchscreen
Home
Back
RESET button
Micro USB connector
Headphone jack
Power
(Press to turn on/off)
Charge/Busy indicator
Menu
The stylus packaged with the Reader may be used for more convenient
touchscreen operation.
The [Home] screen has 2 pages. To navigate [Home] screen pages, press
either of the (Page Turn) buttons or tap either of the on-screen page icons
[ ] [ ].
CHARGE YOUR READER
1. Power on your computer and
connect your Reader with the
supplied USB cable. Do not put
your computer in sleep mode while
charging. Wait until the [USB
connected] screen appears on your
Reader.
2. The Charge/Busy indicator will light up in red while charging. It may
take up to 2.5 hours to fully charge. You can use the Reader while
charging by pressing the (Home) button, or tap the on-screen [Data
Transfer Mode] icon allowing your computer to recognize your Reader
for data transfer. In either way, it may extend the time to fully charge the
battery.
3. The Charge/Busy indicator will turn off automatically after the battery is
fully charged. Disconnect the USB cable from your Reader.
Notes
 It takes up to 5 minutes for the Reader to turn on when charging a completely
depleted battery via your computer. Until the Reader becomes ready, the Charge/
Busy indicator may blink in red 3 times when the (Power) button is pressed. For
an immediate usage while charging, the AC adapter PRSA-AC10 or PRSA-AC1A
(sold separately) is recommended.
 To keep the battery charge, disconnect the USB cable from the Reader if the
computer is in sleep mode or powered off.
TIPS FOR SAVING BATTERY POWER
Sleep Mode
To save battery power and prevent unintentional operation of the
touchscreen, put the Reader in sleep mode by pressing the (Power)
button. To wake the Reader, press the (Power) button again.
Shutdown/Power Off Mode
If the Reader will not be used for a prolonged period, it is recommended to
shut it down. When the Reader is on, press and hold the (Power) button
for 3 seconds. Tap [Yes] on the screen. To restart the Reader, press the
(Power) button.
Automatic Power Saving Modes
The Reader will enter sleep mode after 10 minutes of inactivity. After 3 days
in sleep mode, the Reader will shut down/power off automatically. The
automatic power saving modes cannot be turned off.
Connect to your computer
Charge/Busy indicator
Connect to your computer
Charge/Busy indicator
READ
All books in the Reader can be found under the [Books] on the [Home]
screen. Tap on the book title to open and swipe the touchscreen to turn a
page.
Below are a few examples of your Reader’s many convenient features and
applications for your reading pleasure. For more details, refer to the User
Guide in your Reader under [Books] on the [Home] screen.
Bookmark
Tap right top corner of page.
Zoom in and out
Pinch out and in on the
touchscreen.
Dictionary
Tap and hold a word for 2
seconds and release.
Google or Wikipedia search
Look up a word in the dictionary
and tap Google or Wikipedia.
Font choices and size
Push (Menu) button, tap [Font]
and tap your choice.
Handwriting
Push (Menu) button, tap
[Handwriting] and draw.
Quick Start Guide
Guide de démarrage
 There are two instruction guides provided for your reference. Please
review this Quick Start Guide. For more detailed information, the User
Guide can be found in [Books] on the [Home] screen of your Reader
™ .
 Deux guides d’utilisation vous sont fournis à titre de référence. Veuillez
consulter ce Guide de démarrage. Pour plus d’informations, vous
trouverez le Guide de l’utilisateur sous [Livres] sur l’écran [Accueil] de
votre Reader
™ .
©2011 Sony Corporation / Printed in China
* WPS: Wi-Fi Protected Setup