SUPERTOOTH DISCO TWIN - Manuel

Pai
ring
code 0 0 0 0
Pairing to your Bluetooth A2DP phone / device
Important: Make sure that your Bluetooth phone / device
supports A2DP* (Advanced Audio Distribution Profile) before
proceeding.
1. Select the MASTER DISCO TWIN (see marking at the back of
the unit) and pair it to your Bluetooth A2DP phone / device
to be your LEFT speaker. The other speaker will
automatically be the right speaker.
2. Set the MASTER DISCO TWIN in pairing mode: from OFF,
press and hold the On / Off Button (6) for 6 seconds. The
speaker will announce a welcoming voice “HELLO” followed
by a beep and the Play / Pause Button (3) will start blinking
red. The DISCO TWIN is ready to pair.
3. While the MASTER DISCO TWIN is in pairing mode, access
the Bluetooth menu of your phone / device. Turn on its
Bluetooth function then execute a Bluetooth search to find
the DISCO TWIN (see your phone / device’s manual).
4. When the phone / device displays the list of Bluetooth
devices, select ST TWIN.
5. If the phone / device asks for the password / pin code, enter
0000 and press OK.
6. Pairing is successful if the red LED Indicator stops blinking
followed by a connected beep.
7. Turn on the other DISCO TWIN to reconnect it automatically
to the MASTER DISCO TWIN.
8. The two units of DISCO TWIN are now ready to use with your
phone / device.
(*) A2DP (Advanced Audio Distribution Profile) is a technology
enabling to stream stereo sound from an audio source
(phone, PC, laptop, tablet, Mp3 player) to a stereo speaker or
headset via Bluetooth. To do so both devices must support
this profile.
Note : When you buy the DISCO TWIN, both DISCO TWIN are
paired together. You don’t need to pair them
together. You just need to pair the MASTER DISCO TWIN
with your phone / device as explained in the “Pairing to your
Bluetooth A2DP phone / device” section.
Charging (for each SUPERTOOTH DISCO TWIN)
1. Connect the charger’s plug into the Charge Port (7) of the
DISCO TWIN. Connect the charger to an external power
source.
2. The Charge Indicator (8) is steady red while charging.
Charging is complete when the Charge Indicator (8) goes
green.
Note : If the battery is low, the Play / Pause Button (3) will flash
red.
Turning the SUPERTOOTH DISCO TWIN On and Off
(for each SUPERTOOTH DISCO TWIN)
Power On : Press and hold the On / Off Button (6) for 2
seconds. A welcoming voice saying “Hello” is heard in the
speaker, all the buttons switch on and off automatically.
Note : If you are not playing music, the DISCO TWIN goes to
standby mode automatically after a few seconds and all the
buttons switch off. To check it is turned on, press any button.
All the buttons switch on and off instantaneously.
Power Off : Press and hold the On / Off Button (6) for 2
seconds. The speaker will say “Goodbye”.
Pairing the SUPERTOOTH DISCO TWIN with your
Bluetooth A2DP phone / device
Pair the DISCO TWIN with your phone / device to create the
link or audio connection between the two. Pairing should be
done at first connection with a phone / device.
WARNING
Please make sure you always pair your phone / device
with the MASTER DISCO TWIN. Please refer to the
marking situated at the back of one of the two DISCO TWIN to
find out which one is the MASTER.
DISCO TWIN
USER GUIDE
The SUPERTOOTH DISCO TWIN is made of two portable,
wireless, rechargeable stereo speakers featuring an
avant-garde design and compact footprint.
Users can stream music wirelessly from any cell phone,
tablet, computer, laptop or Mp3 player supporting
Bluetooth A2DP and enjoy a true right / left stereo
effect.
Each unit making the SUPERTOOTH DISCO TWIN kicks
out 16 watts RMS audio power for twice as more power
output and 32 watts of pure sound! Every unit has two
speakers on the front and a high efficiency bass reflex
system at the back.
The integrated rechargeable batteries ensure 3 to 4
hours of non-stop, maximum-volume music, and up to
10 hours of moderately played melodies.
Using the SUPERTOOTH DISCO TWIN with your
Bluetooth A2DP phone / device
Important : The DISCO TWIN needs to be “paired” with your
Bluetooth A2DP phone / device first. Please refer to “Pairing
the SUPERTOOTH DISCO TWIN with your Bluetooth A2DP
phone / device” section.
Streaming music from a Bluetooth A2DP phone / device
1. Turn on the two speakers and wait until the phone / device
reconnects to the MASTER DISCO TWIN and both DISCO
TWIN reconnect automatically.
Note: The MASTER DISCO TWIN is always the LEFT speaker
paired / connected to your phone / device.
2. Go to your phone / device’s music player and play a track or
simply press the Play / Pause Button (3) of the speaker. The
two speakers will announce either “LEFT” or “RIGHT”
followed by the streaming of music played from your
phone / device.
3. This time you will be able to control the music using the
buttons on both speakers.
Reconnecting the SUPERTOOTH DISCO TWIN with a
Bluetooth A2DP phone / device already paired
When you turn it on, the DISCO TWIN reconnects
automatically with the latest paired device. When you leave
the Bluetooth operating range, with the DISCO TWIN turned
ON, it disconnects. When you come back into the Bluetooth
operating range, press the Play / Pause Button (3) for 1 second
to reconnect to the latest paired device. The DISCO TWIN beeps
twice.
Reconnecting both SUPERTOOTH DISCO TWIN together
Once paired together, if you switch off and on both DISCO TWIN,
they will reconnect together automatically.
Note : If both DISCO TWIN are connected together, when you
switch off the MASTER, both DISCO TWIN will switch off
automatically. If you switch off the other DISCO TWIN, this one
only will switch off.
Using the SUPERTOOTH DISCO TWIN with a phone /
device not supporting Bluetooth A2DP
If your phone / device doesn’t support Bluetooth A2DP, you
can connect it directly to the DISCO TWIN via the Stereo Line
Input (9) situated at the back of the DISCO TWIN.
Connecting a phone / device directly to the SUPERTOOTH
DISCO TWIN via the 3.5 mm jack cable
1. Plug the 3.5 mm jack cable into the Stereo Line Input (9)
situated at the back of the DISCO TWIN and the other end to
the output of your phone / device.
2. Press “Play” on your phone / device to stream music directly
to the DISCO TWIN.
3. When the Stereo Line Input is used, you cannot control the
music player using the buttons on the DISCO TWIN. Please
use your phone / device’s buttons directly.
WARNING
When 3.5 mm stereo jack cable is used, ONLY ONE speaker
out of the two DISCO TWIN can be used. You can not
enjoy left / right stereo effect feature of the DISCO TWIN once
the 3.5 mm stereo jack cable is plugged.
Clearing settings or Reset (for each DISCO TWIN)
Clearing the pairing settings of the speaker (for each DISCO
TWIN)
1. Put the speaker to pairing mode: from OFF, press and hold
the On / Off Button (6) for 6 seconds until the Play / Pause
Button (3) blinks red fast. Release the On / Off Button (6) .
2. Press and hold the Play / Pause Button (3) for over 5 seconds
until a beep is heard. The pairing list of phones / devices is
now erased.
Note : Both DISCO TWIN remain paired together after clearing
pairing settings.
Hardware resetting the speaker (for each DISCO TWIN)
Press and hold the On / Off Button (6) for over 35 seconds until
the speaker turns off.
Note : Both DISCO TWIN remain paired together after
hardware resetting the speaker.
Bluetooth operating range
Note : The maximum distance between both DISCO TWIN is
up to 10 meters. Please note this maximum distance depends
on local conditions (walls, windows, etc.).
Folding Cutting