STI 1221A - Manuel

Safety Technology International, Inc.
2306 Airport Road • Waterford, Michigan 48327-1209
Phone: 248-673-9898 • Fax: 248-673-1246
Toll Free: 800-888-4784 • E-mail: [email protected]
Web: www.sti-usa.com
Safety Technology International (Europe) Ltd.
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England • Tel: 44 (0) 1527 520 999
Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only)
E-mail: [email protected] • Web: www.sti-europe.com
INSTALLATION OF STI-1221A STROBE DAMAGE STOPPER ®
All specifications and information shown were current as of publication and are subject to change without notice.
INSTALLATION NOTES
1. Damage Stopper must be installed to comply
with applicable NEC, NFPA and local codes.
2. In areas where frequent wash downs occur,
standoff blocks must be used.
3. Damage Stopper may be installed outdoors
when appliance carries an outdoor rating.
Electronic warranty form at www.sti-usa.com/wc14
1221AIS APRIL2006
CLEANING INSTRUCTIONS
Rinse with water to remove abrasive dust and dirt. Wash with soap or mild detergent, using a soft cloth
(do not scrub). Rinse once more then dry with a soft cloth or chamois. To remove grease or wet paint,
rub gently with a cloth wetted with naphtha. Then wash and rinse. DO NOT USE RAZOR BLADES.
INSTALLATION INSTRUCTIONS - REFER TO EXPLODED VIEW
1. Insert the (4) 06297T external mounting tabs into the frame assembly slots.
2. Using back box assembly as a template, place against mounting surface at proper location according
to NFPA 72.
3. Mark and drill (4) holes 1/4 in. (6.3mm) diameter, 1 1/4 in. (32mm) deep.
4. Insert the (4) anchors into the wall.
5. Mount back box to wall with screws.
6. Install electrical fittings as needed.
7. Install strobe appliance.
8. Install cover with clips and screws.
9. Test appliance according to appliance manufacturer’s instructions.
FOR CONDUIT INSTALLATION (NOT INCLUDED)
“A” Rain-tight hub with neoprene o-ring threaded for 3/4 in. NPT
rigid conduit
“B” 3/4 in. female adapter
“C” 3/4 in. - 1/2 in. reducing bushing
“D” Galvanized 1/2 x 1 in. conduit nipple
“E” 1/2 in. conduit lock nut
“F” 4 in. square back box
“G” 4 in. square box extension (optional). Use to extend strobe into
cover area.
1
2
B
C
D
F
E
G
HORIZONTAL CENTERLINE
OF ENCLOSURE
CENTERLINE
MOUNTING BOSS
FOR BACKBOX
MOUNTING
HEIGHT 80 in.
FRONT VIEW OF ENCLOSURE
#8-32 x 3/8 in.
MACHINE SCREWS
(NOT INCLUDED)
DRILL FOR CONDUIT ENTRY
HEIGHT
7.75 in.(197mm)
WIDTH
5.25 in.(133mm)
DEPTH
6.5 in.(165mm)
629761 NEOPRENE GASKET
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
19033 ANCHOR
(4) PROVIDED
A
06297T MOUNTING
TABS (4) PROVIDED
06297A BACKBOX
NEOPRENE GASKET
3 3/8 in.
(86mm)
3/4 in.(44mm)
629763 STANDOFF BLOCKS
(4) PROVIDED
19047 #8-32 x 3/8 in. SOCKET
HEAD CAP SCREWS
(4) PROVIDED 01221 COVER ONLY
!
629764 RETAINING CLIP
(4) PROVIDED
629762 DRAIN SCREEN
INCLUDED BUT NOT
FACTORY INSTALLED
01221 COUVERCLE SEULEMENT
1
2
B
C
D
F
E
G
HORIZONTAL CENTERLINE
OF ENCLOSURE
CENTERLINE
MOUNTING BOSS
FOR BACKBOX
MOUNTING
HEIGHT 80 in.
FRONT VIEW OF ENCLOSURE
#8-32 x 3/8 in.
MACHINE SCREWS
(NOT INCLUDED)
DRILL FOR CONDUIT ENTRY
HEIGHT
7.75 in.(197mm)
WIDTH
5.25 in.(133mm)
DEPTH
6.5 in.(165mm)
629761 NEOPRENE GASKET
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
19033 ANCHOR
(4) PROVIDED
A
06297T MOUNTING
TABS (4) PROVIDED
06297A BACKBOX
NEOPRENE GASKET
3 3/8 in.
(86mm)
3/4 in.(44mm)
629763 STANDOFF BLOCKS
(4) PROVIDED
19047 #8-32 x 3/8 in. SOCKET
HEAD CAP SCREWS
(4) PROVIDED 01221 COVER ONLY
!
629764 RETAINING CLIP
(4) PROVIDED
629762 DRAIN SCREEN
INCLUDED BUT NOT
FACTORY INSTALLED
01221 COUVERCLE SEULEMENT
1
2
B
C
D
F
E
G
HORIZONTAL CENTERLINE
OF ENCLOSURE
CENTERLINE
MOUNTING BOSS
FOR BACKBOX MOUNTING
HEIGHT 80 in.
FRONT VIEW OF ENCLOSURE
#8-32 x 3/8 in.
MACHINE SCREWS
(NOT INCLUDED)
DRILL FOR CONDUIT ENTRY
HEIGHT
7.75 in.(197mm)
WIDTH
5.25 in.(133mm)
DEPTH
6.5 in.(165mm)
629761 NEOPRENE GASKET
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
19033 ANCHOR
(4) PROVIDED
A
06297T MOUNTING
TABS (4) PROVIDED
06297A BACKBOX
NEOPRENE GASKET
3 3/8 in.
(86mm)
3/4 in.(44mm)
629763 STANDOFF BLOCKS
(4) PROVIDED
19047 #8-32 x 3/8 in. SOCKET
HEAD CAP SCREWS
(4) PROVIDED 01221 COVER ONLY
!
629764 RETAINING CLIP
(4) PROVIDED
629762 DRAIN SCREEN
INCLUDED BUT NOT
FACTORY INSTALLED
01221 COUVERCLE SEULEMENT
INSTALL CLAMP IN NOTCH 2 AS SHOWN
INTERNAL DIMENSIONS
REMARQUES SUR L’INSTALLATION
1. Le Stopper de dégâts doit être installé de sorte
à être conforme avec les normes NEC, NFPA
applicables et les codes locaux.
2. Dans les zones où des jets d’eau fréquents
surviennent, des blocs de détection à distance
doivent être utilisés.
3. Il est possible d’installer un Stopper de dégâts à
l’extérieur lorsque l’appareil est homologué pour
utilisation à l’extérieur.