STI 1219 - Manuel

Safety Technology International, Inc.
2306 Airport Road • Waterford, Michigan 48327-1209
Phone: 248-673-9898 • Fax: 248-673-1246
Toll Free: 800-888-4784 • E-mail: [email protected]
Web: www.sti-usa.com
Safety Technology International (Europe) Ltd.
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England • Tel: 44 (0) 1527 520 999
Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only)
E-mail: [email protected] • Web: www.sti-europe.com
INSTALLATION OF STI-1219 STOPPER ® DOME FOR HORN/SPEAKER/STROBE
All specifications and information shown were current as of publication and are subject to change without notice.
INSTALLATION NOTES
1. To minimize strobe light loss, regardless of the type of horn/strobe appliance used, the clear
section (not the section containing the cutout slots) must be centered over the strobe light lens.
Failure to follow these instructions may lead to light loss transmission.
2. Stopper Dome must be installed to comply with applicable NEC, NFPA and local codes.
3. Stopper Dome may be installed outdoors when appliance carries an outdoor rating.
Electronic warranty form at www.sti-usa.com/wc14
1219IS APRIL2006
CLEANING INSTRUCTIONS
Rinse with water to remove abrasive dust and dirt. Wash
with soap or mild detergent, using a soft cloth (do not
scrub). Rinse once more then dry with a soft cloth or
chamois. To remove grease or wet paint, rub gently with a
cloth wetted with naphtha. Then wash and rinse. DO NOT
USE RAZOR BLADES.
INSTALLATION INSTRUCTIONS - REFER TO EXPLODED VIEW
1. Using enclosed spacer assembly as a template, place
against mounting surface at proper location according to
NFPA 72.
2. Mark and drill (4) holes 1/4 in. (6.3mm) diameter, 1 in.
(25mm) deep.
3. Insert the (4) anchors into the wall.
4. Mount enclosed spacer to wall with screws.
5. Install electrical fittings as needed.
6. Install horn/strobe appliance.
7. Install cover with washers and screws.
8. Test appliance according to appliance manufacturer’s
instructions.
NEMA 4X CONDUIT HUB
(NOT PROVIDED)
NOTE: ACCESS HOLE MUST BE FIELD
DRILLED TO APPROPRIATE SIZE
HOLE MUST BE DRILLED
AS SHOWN, CENTERED ON
UPPER OR LOWER FLAT
SURFACE
01222 ENCLOSED SPACER
(1) PROVIDED
01289 APPLIANCE MOUNTING PLATE
(1) PROVIDED
19051 PHILLIPS FLAT HEAD SCREW
#8-32 x 3/8 in.
(4) PROVIDED
EXISTING HORN/STROBE APPLIANCE
070498A GASKET
(1) PROVIDED
01215 COVER
(1) PROVIDED
19049 WASHER
(6) PROVIDED
19050 #8-32 x 3/4 in.
SOCKET HEAD CAP SCREW
(6) PROVIDED
19013 SCREW #10 x 1 1/2 in.
(4) PROVIDED
10933 ANCHOR
(4) PROVIDED
DRILL (4) 1/4 in.(6.3mm)
DIA. HOLES
IN AREAS WHERE
FREQUENT WASHDOWNS
OCCUR WASHERS MAY BE
USED TO STAND OFF ENCLOSED SPACER
NOT PROVIDED
9.37 in.(238mm)
2.87 in.(73mm)
4.25 in.
(108mm)
01289 APPLIANCE
MOUNTING PLATE
NEMA 4X CONDUIT HUB
(NOT PROVIDED)
NOTE: ACCESS HOLE MUST BE FIELD
DRILLED TO APPROPRIATE SIZE
HOLE MUST BE DRILLED
AS SHOWN, CENTERED ON
UPPER OR LOWER FLAT
SURFACE
01222 ENCLOSED SPACER
(1) PROVIDED
01289 APPLIANCE MOUNTING PLATE
(1) PROVIDED
19051 PHILLIPS FLAT HEAD SCREW
#8-32 x 3/8 in.
(4) PROVIDED
EXISTING HORN/STROBE APPLIANCE
070498A GASKET
(1) PROVIDED
01215 COVER
(1) PROVIDED
19049 WASHER
(6) PROVIDED
19050 #8-32 x 3/4 in.
SOCKET HEAD CAP SCREW
(6) PROVIDED
19013 SCREW #10 x 1 1/2 in.
(4) PROVIDED
10933 ANCHOR
(4) PROVIDED
DRILL (4) 1/4 in.(6.3mm)
DIA. HOLES
IN AREAS WHERE
FREQUENT WASHDOWNS
OCCUR WASHERS MAY BE
USED TO STAND OFF ENCLOSED SPACER
NOT PROVIDED
9.37 in.(238mm)
2.87 in.(73mm)
4.25 in.
(108mm)
01289 APPLIANCE
MOUNTING PLATE
REMARQUES SUR L’INSTALLATION
1. Afin de minimiser la perte de lumière stroboscopique, quel que soit le type d’alarme sonore/de
stroboscope utilisé, la section dégagée (et NON la section contenant les fentes de découpe), doit
être centrée sur l’objectif stroboscopique. Le fait d’omettre ces instructions risque d’entraîner la
perte de diffusion de la lumière.
2. Le dôme Stopper doit être installé de sorte à être conforme avec les normes NEC, NFPA applicables
et les codes locaux.
3. Il est possible d’installer un dôme Stopper à l’extérieur lorsque l’appareil est homologué pour
utilisation à l’extérieur.