Whirlpool Cabrio W10164159B - Manuel (Page 21)

21
Cycle tips
■ Dry most loads using the preset cycle settings.
■ Refer to the Automatic or Timed Preset Cycle Settings chart (in
the “Cycles” section) for a guide to drying various loads.
■ Drying temperature and dryness level are preset when you
choose an Automatic Cycle. You can select a different
dryness level, depending on your load, by pressing Dryness
and choosing More, Normal, Less, or Damp.
NOTE: You cannot use the Time Adjust and you cannot
choose a Temperature with the Automatic Cycles.
■ If you wish to adjust the cycle length of a Timed Cycle, press
the Time Adjust up or down arrows. Adjust the temperature
of a Timed Cycle by pressing Temp until the desired
temperature is selected.
NOTE: You cannot choose a dryness level with Timed
Cycles.
Status Lights
Follow the progress of your dryer with the drying Status indicator
lights.
Sensing
■ In an Automatic Cycle, the Sensing light illuminates until a wet
item is detected.
■ In the Timed Cycle, the Sensing light illuminates at the beginning
of a cycle and turns off 5 minutes into the cycle.
Wet
The Wet light illuminates at the beginning of an Automatic Cycle if a
wet item is detected.
■ In an Automatic Cycle, if a wet item is not detected after
approximately 5 minutes, the dryer goes directly into Cool Down
and the Cool Down and the WRINKLE SHIELD™ setting
indicators illuminate, if selected.
■ In a Timed Cycle, wet items are not detected. The dryer will
continue to run for the length of time selected, and the Wet light
will illuminate. The damp light will not illuminate.
■ In the Enhanced Touch Up or the Quick Refresh Steam Cycles,
the Wet light comes on after the water has been sprayed into the
drum, 5-6 minutes into the cycle. The Wet light illuminates until
the dryer goes into Cool Down with 1 minute of time remaining.
Damp
The Damp light illuminates in an Automatic Cycle when the laundry
is approximately 80% dry. Damp Dry Signal beeps, if selected. See
“Options.”
Cool Down
The Cool Down light illuminates during the cool down part of the
cycle. Laundry cools for ease in handling.
Done
The Done light illuminates when the drying cycle is finished. This
indicator stays on during the WRINKLE SHIELD™ setting.
WRINKLE SHIELD™ Setting
The WRINKLE SHIELD™ setting light illuminates when this option is
selected. This indicator stays on during the WRINKLE SHIELD™
setting.
Indicator lights
Other indicator lights show Cycle, Modifiers, Options, and Cycle
Signal settings selected. The display shows the estimated or actual
time remaining.
Cycles
Select the drying cycle that matches the type of load you are drying.
See the Automatic, Steam, or Timed Preset Cycle Settings Charts.
Automatic Cycles
Automatic Cycles allow you to match the cycle to the load you are
drying. See the following Automatic Preset Cycle Settings chart.
Each cycle dries certain fabrics at the recommended temperature. A
sensor detects the moisture in the load and automatically adjusts
the drying time for optimal drying.
Heavy Duty
Use this cycle to get high heat for heavyweight mixed loads,
cottons, and jeans.
Normal
Use this cycle to get medium heat for drying sturdy fabrics such as
work clothes.
Casual
Use this cycle to get low heat for drying no-iron fabrics, such as
sport shirts, casual business clothes, and permanent press blends.
Delicate
Use this cycle to get extra-low heat to gently dry items such as
lingerie, blouses, or washable knit fabrics.
Automatic Preset Cycle Settings
Automatic Cycles
Load Type
Temperature
HEAVY DUTY
Heavyweight mixed loads, cottons,
jeans
High
NORMAL
Corduroys, work clothes
Medium
CASUAL
Business casual clothes, permanent
press, synthetics
Low
DELICATE
Lingerie, blouses, washable knit fabrics
Extra-Low