Installation, Television location, Optional cable connections – Panasonic CT-32HC15 Manuel d'utilisation

Page 6: Ac power supply cord, Cable / antenna connection, Remote control battery installation, English

Advertising
background image

4

z

I

NSTALLATION

ENGLISH

Installation

Television Location

This unit is intended to be used with an optional stand or
entertainment center. Consult your dealer for available
options.

Avoid excessive sunlight or bright lights, including
reflections.

Keep away from excessive heat or moisture. Inadequate
ventilation may cause internal component failure.

Fluorescent lighting may reduce remote control
transmitting range.

Keep away from magnetic equipment, including motors,
fans and external speakers.

WARNING: Use this television receiver only with the
cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart
is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over. In order to
avoid injury to children, never place your television receiver on a
piece of furniture that is capable of being tilted by a child leaning
on it, pulling on it, standing on it, or climbing on it. A falling
television can cause serious injury or even death.

CT-32HC15, CT-32HC15U:

CAUTION: These television receivers for use only with
PANASONIC TY-32SC15T stand. Use with other carts
(or stands) is capable of resulting in instability causing
possible injury.

CT-32HL15, CT-32HL15U:

CAUTION: These television receivers for use only with
PANASONIC TY-32HL15T stand. Use with other carts
(or stands) is capable of resulting in instability causing
possible injury.

Optional Cable Connections

Shielded audio and video cables should be used between
components. For best results:

Use 75-ohm coaxial shielded cables.

Use appropriate input and output connectors, that match
your component connectors.

Avoid long cables to minimize interference.

AC Power Supply Cord

CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT
OF AC OUTLET AND FULLY INSERT. DO NOT
USE A PLUG WITH A RECEPTACLE OR OTHER
OUTLET UNLESS THE BLADE CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.

PROTECT POWER CORDS FROM BEING WALKED ON, ROLLED
OVER, CRIMPED, BENT, OR PINCHED, PARTICULARLY AT PLUGS,
CONVENIENCE RECEPTACLES, AND THE POINT WHERE THEY EXIT
FROM THE APPARATUS.

Cable / Antenna Connection

For proper reception, either a cable or antenna connection
is required.
Cable Connection

Connect the cable supplied by your local
cable company. Tighten with fingers only.
Use of any tool (e.g. pliers) for tightening
may result in tuner damage.
Note:

A cable converter box may be
required for proper reception.
Check with your local cable
company for compatibility requirements.

Antenna Connection

For proper reception of VHF/UHF channels, an

external antenna is required. For best reception an
outdoor antenna is recommended.

Connect home antenna to

ANT connection on back of
television. Select TV mode in
the SET UP menu.

Note:

Cable Mode is preset at the
factory. Antenna users must
change to TV Mode in the Set
Up menu (page 15).

Remote Control Battery Installation

Requires two AA batteries (supplied).

Procedure

1.

Turn the remote control face down. Remove battery
cover by pressing down on the marking on the cover
and sliding it off in the direction indicated.

2.

Install batteries matching (+) and (-) polarity signs.

3.

Replace the battery cover by sliding in reverse until the
lock snaps.

Note:

Incorrect installation can cause battery leakage and
corrosion that will damage the Remote Control.

Precautions

Replace batteries in pairs.

Do not mix battery types (zinc carbon with alkaline).

Do not recharge, heat, short-circuit, disassemble, or
burn batteries.

Polarized plug

75 Ohm VHF/UHF

on back of TV

Incoming Cable from

Cable Company

Incoming Cable from

Home Antenna

AA / 1.5A

AA / 1.5A

Battery Polarity

1

2

AA

/ 1.5A

AA

/ 1.5A

3

Advertising