Keurig B60 - Manuel (Page 4)

Stopping the Brew Process
If you need to stop the brewing after the
process has started, press the Power Button to
turn the Brewer ‘OFF’. The flow of coffee
or tea will stop, the heating element will shut
off and the blue lights illuminating the brew
buttons and Water Reservoir will disappear.
Adding Water
The LCD Control Center of your Brewer will
indicate when the water level in the tank is low
or if the Water Reservoir has been removed by
displaying the words ‘ADD WATER’. The
Brewer will not allow you to brew when ‘ADD
WATER’ is displayed.
The Water Reservoir can be filled in two ways.
1. Lift off the Water Reservoir Lid and pour
water directly into the Water Reservoir
while it is still attached to the Brewer, then
replace the Lid.
2. Remove the Water Reservoir from Brewer
by first removing Lid from the Water
Reservoir, then lifting the Water Reservoir
straight up and away from Brewer. Fill with
water. Place the Water Reservoir back on
the Brewer and replace the Lid.
Brewing Hot Water
Your Brewer is able to produce a cup of hot
water for making hot chocolate, for use in
cooking, for making soups, etc. Simply raise
and lower the handle on the Brewer without
adding a K-Cup
® portion pack. The LCD Control
Center will display 'READY TO BREW' and the
Cup, Mug and Travel Mug Buttons will blink. Be
sure to have a mug or cup on the Drip Tray and
then select the size you would like.
Purging the Brewer
If your Brewer has not been used for more
than one week, you should purge the water
from the inner tank.
1. If there is water in the Water Reservoir,
remove the Lid, then lift the Water Reservoir
straight up and away from Brewer. Discard
water, rinse and refill with water. Place the
Water Reservoir back on the Brewer and
replace the Lid. (If there is no water in the
Water Reservoir, simply refill.)
2. Be sure the Brewer is turned on. Raise and
lower the handle on the Brewer without
inserting a K-Cup
® portion pack.
3. The LCD Control Center will display 'READY
TO BREW' and the Cup, Mug and Travel
Mug Buttons will blink. Be sure to have a
travel mug on the Drip Tray and then select
the Travel Mug size brew.
4. Repeat steps 2 and 3 one more time to
completely purge water from inner tank.
If you are experiencing any problems with
your Brewer, please contact Customer
Service at 1-866-901-BREW (2739).
8 9
SECTION 2
LCD Control Center
Setting the Clock
Setting the clock is optional. When the clock
is set, the time will appear in the LCD Control
Center. NOTE: You must set the clock if you
will be using the Auto On/Off Time program-
ming feature.
a. Press the button below 'MENU'.
b. The word 'OFF' will appear at the bottom
of the LCD Control Center to indicate that
the clock is not set. The programming
options will appear on the LCD Control
Center with a small arrow pointing to 'SET
CLOCK'. H (Hour) and M (Minute) will
appear and blink.
c. Press or hold the blue Cup button under
the blinking H until you have reached the
appropriate hour. If the hour has passed
12, the indicator switches from AM to PM.
d. Press or hold the blue Travel Mug button
under the blinking M to set the minutes.
e. When you have reached the correct time,
press the menu button five times to scroll
through the remaining programming
options and exit the programming mode.
f. The correct time should now be displayed
in the LCD Control Center.
Programing On/Off Features
The Brewer provides three modes so that you
can enjoy gourmet coffee or tea on your own
schedule. By programming your Brewer to
turn on each morning, you will never have to
wait for the Brewer to warm up to brew a
gourmet cup of coffee.
1. Leave it ON all the time (recommended).
The Brewer can be left on all the time so
that it is always ready to brew a fresh cup
of gourmet coffee or tea. To turn the
Brewer off at any time, simply press the
Power Button. (Note: Although the clock
remains on if set, you can not brew a cup
of coffee or tea.) Press the Power Button
again to restore power to the Brewer. You
will have to wait for the water to heat up
before the Brewer is ready to brew.
2. Set the Brewer to turn off at a specified
period of time after the last brew.
a. Press the MENU button twice to pro-
gram the AUTO OFF feature. The LCD
Control Center will now display the pro-
gramming options with a small arrow
next to 'SET AUTO OFF'.
b. Press or hold the blue CUP button under
the blinking H to advance 1 hour at a
time, up to 9 hours.
CONTROLS & INDICATORS
NOTE: You may get less coffee or tea in
your cup during your next brew. We
recommend that you perform a cleansing
brew with water only after a terminated brew.
Then your NEXT brew will be the volume
you have selected.
IMPORTANT: Do not remove the Water
Reservoir during the brewing process.
NOTE: If power is interrupted to the
Brewer by unplugging it, or if power is
lost, follow the procedure above to reset
the time as the clock will not be visible
until the time is set.
ADD
WATER
NOT READY
READY
SET CLOCK
AUTO OFF
ON OFF TIME
BREW TEMP
MENU
H M
NOT
OFF
READY
SET AUTO OFF
CLOCK
ON OFF TIME
BREW TEMP
MENU
H
NOT