Reznor EGP Unit Installation Manual - Manuel (Page 2)

MAINTENANCE
The motor of this heater is permanently lubricated. It is the responsibility
of the user to evaluate whether to clean the heater according to the
amount of dirt accumulated on the air inlets and outlets as well as inside
of the heater. Accumulated dirt can lead to a component malfunction.
There is a fi re hazard if the product is not installed and maintained in
accordance with these guidelines.
To clean the heater :
1- Turn off the thermostat and remove the plug from the wall electrical
outlet. Let the heater cool a few minutes after turning it off because
it will stay warm for a while.
2- Clean the air inlet grille with a vacuum cleaner with a brush, with
a damp cloth and mild soap. Do not use chemical or fl ammable
cleaning. If necessary, the heater may be dusted with a compressed
air jet.
POWER CORD
1- This heater operates at a voltage 208 and 240 volts. The heater plug
is a type corresponding to Figure 1. There is no adapter for this
confi guration of blades and no adapter should be used. This plug
fi ts a wall electrical outlet 208/240 volt grounded. When the plug
is installed properly, it gives the cord a grounding in the heater that
protects users against electric shock.
CAUTION: In the United States, the law prohibits the use of
an extension cord with a heater of this type.
WARRANTY
The manufacturer warrants the component parts of its products
against defects in material and workmanship for a one year period
following the date of purchase, under normal use and service, when
proof of purchase of such is provided to the manufacturer. The
obligation of the manufacturer, under the terms of this warranty,
will be to supply a new unit and this releases the manufacturer from
paying the installation costs or other secondary charges linked to
replacing the unit or the component part(s).
USER GUIDE
1- Make sure the heater’s power cord is not damaged. It is important to
regularly inspect the cord and wall electrical outlet.
2- Make sure the voltage and amperage listed on the nameplate of the
heater are compatible with the power supply.
3- When starting after a long storage period, perform cleaning to prevent
odors burned and whitish smoke. Refer to the ‘‘MAINTENANCE’’
section to clean the heater.
4- The heater must be installed to ensure horizontal air discharge only
and the back of the heater should not be placed within 3 ½ in. (9 cm)
from the wall and the top of the heater within 6 in. (15 cm) from the
ceiling.
4.1- Install the heater on a wall using the supplied bracket..
4.2- Fix the heater to a maximum height of 8 ft (2.44 m).
4.3- Use the keyholes to fi x the heater.
NOTE - The wall must be able to support the weight of the
heater, 11 lb (5 kg). Secure the bracket with (2) screws ¼ in.
diameter x 1 ½ in. length (not supplied) to the wall at a distance
of 12 in. (30.5 cm) from each other.
4.4- Slide the bracket of the heater over the 2 screws into the
keyholes.
5- Plug the heater into a proper wall electrical outlet and place the
heater to direct the airfl ow.
AMERICAN VERSION ONLY: An amber light is lit to indicate
that the power is on.
6- Make sure the connector on the power cord of the heater is inserted
into the wall electrical outlet before use.
7- Rotate thermostat knob full clockwise. The fan will start and the
element will heat.
8- When the desired temperature is reached, turn the thermostat
counter-clockwise slowly until you hear a click. To set the room
temperature, turn slowly the thermostat clockwise or counter-
clockwise.
9- To disconnect the heater, turn off the thermostat and remove the
plug from the wall electrical outlet. Let the heater cool a few
minutes after turning it off because it will stay warm for a while.
10- Roll up the power cord around the handle of the heater when it is
unplugged and has cooled and store the heater in a dry place.
11- Please note that the heater is powered on even if the thermostat is in
the off position. So you can get an electric shock as the power cord
is connected.
Figure 1
Confi guration of the plug:
NEMA 6-20P
20A, 250VAC