Whirlpool WGI925C0BS - Manuel (Page 20)

20
To Delay Start Self-Clean:
Before delay starting Self-Clean, make sure the oven door is
completely closed or it will not lock and the cycle will not begin.
1. Press START TIME.
“PRESS 1 FOR Upper Oven” will scroll in the upper text area,
and “PRESS 2 FOR Lower Oven” will scroll in the lower text
area.
2. Press the “1” or “2” number keypad to select the desired
oven.
“--:--” will be displayed, and “Set starting time. Push START”
will scroll from right to left in the selected oven text area for
30 seconds or until the number keypad is pressed.
3. Use the number keypad to enter the delay start time. The
delay start time is the amount of time by which you want to
delay the start. Press START for the desired oven.
“Select cooking/cleaning mode” will scroll in the selected
oven text area for 30 seconds or until a cooking cycle is
selected.
4. Press PRECISE CLEAN.
“REMOVE RACKS” will appear in the upper oven text area,
followed by “PRECISE CLEAN.” “Set Clean Time or Push
START” will scroll in the lower oven text area.
5. Press START to accept the recommended clean time shown
in the HR:MIN area, or use the number keypad to select a
desired cleaning time between 2 and 4 hours
6. Press START for the desired oven.
“UnLock in XX hrs” will display.
7. “Locking” will display until the door is locked. “Precise
CLEAN starts at XX:XX” will scroll until the selected delayed
start time.
After the door is locked, “CLEAN UPPER” or “CLEAN
LOWER” will scroll in the selected oven text area until the
clean cycle is finished.
When the self-clean cycle ends:
“Cln COMPLETE will scroll in the selected oven text area. After
5 seconds, “OVEN COOLING” will scroll in the display until the
oven temperature falls below 500°F (260°C).
“UNLOCKING” will be displayed until the oven door unlocks and
the lock icon turns off.
Steam Clean
The Steam Clean feature is designed for light oven cavity bottom
cleaning on models that have hidden bake in both ovens.
Allow the range to cool to room temperature before using the
Steam Clean feature. If your oven cavity is above 100°F (38°C),
“OVEN COOLING” will appear in the display and the Steam
Clean feature will not activate until it cools down.
■ Remove all racks and accessories from the oven cavity.
■ For best results, use 4 oz (118 mL) of distilled or filtered water.
■ The Steam Clean feature will take a total of 20 minutes. A
beep will sound at the end of the cycle.
IMPORTANT: Because the water in the oven bottom is hot, do
not open the oven door during the Steam Clean cycle.
Press any CANCEL at any time to end the cycle. The display will
return to the time of day.
Helpful Hints
■ Once the Steam Clean cycle is complete, remove all
remaining water in the bottom of the oven with a sponge or
cloth.
■ Wipe any remaining moisture from the oven door interior,
oven cavity interior sides, and cooktop.
■ Use a soft brush or nylon scrubber to wipe the oven interior.
This may help with more stubborn stains.
■ It is recommended to use distilled or filtered water, as tap
water may leave mineral deposits on the oven bottom. Use a
cloth soaked with vinegar or lemon juice to remove any
mineral deposits that may be left after the Steam Clean cycle.
■ If the oven is heavily soiled, use the Self-Clean cycle. The
Steam Clean cycle may be used first to eliminate most of the
debris, resulting in a more effective self-clean.
To SteamClean:
1. Remove all racks and accessories from the oven cavity.
2. Press STEAM CLEAN.
3. “PRESS 1 FOR Upper Oven” will scroll in the upper oven text
area and “PRESS 2 FOR Lower Oven” will scroll in the lower
oven text area.
4. Use the number keypad to select the desired oven.
5. “REMOVE RACKS” will display, followed by “STEAM CLEAN”
in upper text area.
“Open door pour 4 Oz water to oven base and push START”
will scroll in the lower text area.
6. Open the oven door of the selected oven and pour 4 oz
(118 mL) of distilled or filtered water to the oven bottom. Then
close the oven door.
7. Press START for the desired oven.
“Steam CLEAN” is displayed in the lower text area.
8. After 20 minutes, a beep will sound to signal the end of the
cycle.
9. Press CANCEL for the desired oven to clear the display.
10. Remove any excess water with a sponge or cloth and wipe
down oven interior. If needed, use a non-scratch copper
scrubbing pad to remove stubborn soils.