Whirlpool Cabrio W10164159B - Manuel (Page 20)

20
■ Adjust Dryness.
NOTE: Dryness selections can be made only while using
Automatic Cycles.
How the AccelerCare ® Drying System Works
Moisture-sensing strips and temperature sensors inside the
dryer drum monitor how fast the load is drying, how hot the air
should be and when clothes are dry. The system automatically
stops the cycle to help save time and avoid overdrying.
To use a Timed Cycle
■ Turn knob to desired Timed Cycle.
■ Press the TIME ADJUST up or down arrows until the desired
drying time is displayed. Press the up or down arrows and
the time will change by 1-minute intervals. Press and hold
the up or down arrows and the time will change by 5-minute
intervals.
NOTE: The Time Adjust features can be used only with
the Timed Dry and the Enhanced Touch Up cycles.
■ Press TEMP until the desired temperature illuminates.
NOTE: The Temp feature can be used only with the Timed
Dry and the Enhanced Touch Up cycles.
NOTE: During the Timed Dry Cycle, you can change the
settings for Time, Temp, the WRINKLE SHIELD™ setting,
and the End of Cycle Signal.
5. (OPTIONAL STEP) If desired, select OPTIONS. For more details,
see “Options.”
6. (OPTIONAL STEP) If desired, press END OF CYCLE SIGNAL. A
signal will sound to alert you when a cycle ends. For more details,
see “End of Cycle Signal.”
7. Press START. Be sure the door is closed.
■ If you do not press Start within 5 minutes of selecting the
cycle, the dryer automatically shuts off.
■ If you wish to end your drying cycle after pressing Start,
press PAUSE/CANCEL twice.
To use a Steam Cycle
(Quick Refresh and Enhanced Touch Up)
■ Press POWER.
■ Turn the knob to select either the Enhanced Touch Up or the
Quick Refresh cycles.
■ Press the TIME ADJUST up or down arrows until the desired
drying time is displayed. Press the up or down arrows and
the time will change by 1-minute intervals. Press and hold
the up or down arrows and the time will change by 5-minute
intervals.
NOTE: The Time Adjust features can be used only with
the Timed Dry and the Enhanced Touch Up cycles.
■ Press TEMP until the desired temperature illuminates.
NOTE: The Temp feature can be used only with the Timed
Dry and the Enhanced Touch Up cycles. Only the Medium
and High temperature settings can be used for the
Enhanced Touch Up Cycle.
NOTE: During the Enhanced Touch Up cycle, you can
change the settings for Time Adjust and Temp. Open the
door or press PAUSE/CANCEL once to pause the cycle,
or press PAUSE/CANCEL twice to cancel a cycle.
Stopping, Pausing, or Restarting
To stop or pause your dryer at any time
Open the door or press PAUSE/CANCEL once. Press PAUSE/
CANCEL twice to cancel a cycle.
To restart the dryer
Close the door. Press START until dryer starts.
NOTE: Drying will continue from where the cycle was interrupted if
you close the door and press Start within 5 minutes. If the cycle is
interrupted for more than 5 minutes, the dryer will shut off. Select
new cycle settings before restarting the dryer.
Drying and Cycle Tips
Select the correct cycle and dryness level or temperature for your
load. If an Automatic Cycle is running, the display shows the
estimated cycle time when your dryer is automatically sensing the
dryness level of your load. If a Timed Cycle is running, the display
shows the exact number of minutes remaining in the cycle.
Cool Down tumbles the load without heat during the last few
minutes of all cycles. Cool Down makes the loads easier to handle
and reduces wrinkling. The length of the Cool Down depends on the
load size and dryness level.
Drying tips
■ Follow care label directions when they are available.
■ If desired, add a fabric softener sheet. Follow package
instructions.
■ To reduce wrinkling, remove the load from the dryer as soon as
tumbling stops. This is especially important for permanent
press, knits, and synthetic fabrics.
■ Avoid drying heavy work clothes together with lighter fabrics.
This could cause overdrying of lighter fabrics and lead to
increased shrinkage or wrinkling.