Dishwasherefficiencytips, Cycleselectionchart, Dishwasher efficiency tips – Roper RUD1000 Manuel d'utilisation
Page 11: Cycle selection chart
11
Dishwasher Efficiency Tips
Hot water dissolves and activates the dishwashing detergent.
Hot water also dissolves grease on dishes and helps glasses dry
spot-free. For best dishwashing results, water must be at least
120°F (49°C) as it enters the dishwasher. Loads may not wash as
well if the water temperature is too low.
To check water temperature
1.
Run hot water at the faucet closest to your dishwasher for at
least 1 minute.
2.
Place a candy or meat thermometer in a glass measuring
cup.
3.
Check the temperature on the thermometer as the water is
running into the cup.
4.
If the water temperature at the faucet is below 120°F (49°C),
have a qualified person raise the water heater’s thermostat
setting.
■
To save water, energy and time, do not rinse dishes before
putting them into the dishwasher.
■
Use a low energy, quick, or short cycle whenever possible.
These cycles use less hot water and energy than the Normal
cycle.
■
Use a delay feature (on some models) to run your dishwasher
during off-peak hours. Local utilities recommend avoiding
heavy usage of energy at certain times of day.
■
During the summer, run your dishwasher at night. This
reduces daytime heat buildup in the kitchen.
■
Use the energy-saving dry option whenever possible. Allow
longer drying times (overnight) when using these options. Use
a rinse aid to improve drying.
■
Use cycles or options that add extra heat to the wash or rinse
portion of the cycle only when needed.
■
Run your dishwasher with full loads. Run a rinse cycle after
meals until the dishwasher is full.
Cycle Selection Chart
Select the wash cycle. If the door is latched, you will hear the
cycles start and stop as the Cycle Control knob passes each
cycle mark. This is normal and does not hurt the dishwasher. If
you prefer, you can set the Cycle Control knob with the door
unlatched.
NOTE:
Use the Energy-Saver Dry option with the Rinse & Hold
cycle (on some models).
Models with a rocker switch:
Turn the Cycle Control knob to the desired cycle.
Models with 5 or 7 pads:
Press the desired cycle. Turn the Cycle Control knob to the
desired cycle. To use Rinse & Hold, press any cycle and turn the
Cycle Control knob to RINSE & HOLD.
A “●” shows what steps are in each cycle. Your model may have
some or all of the cycles shown.
Water usage is shown in U.S. gallons/liters.
Cycle time includes dry time.
Wash
Rinse
Rinse
Main
Wash
Rinse
Final
Rinse
Dry
Time
(min)
Water
Usage
(gal/L)
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
98
8.6/32.7
Wash
Rinse
Rinse
Main
Wash
Rinse
Final
Rinse
Dry
Time
(min)
Water
Usage
(gal/L)
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
98
8.6/32.7
Wash
Rinse
Rinse
Main
Wash
Rinse
Final
Rinse
Dry
Time
(min)
Water
Usage
(gal/L)
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
90
7.2/27.2
Use this cycle for hard-to-
clean, heavily-soiled pots,
pans, casseroles, and
regular tableware.
Use both
detergent
dispenser
sections.
POTS &
PANS
Use this cycle for loads
with heavy food soil.
Use both
detergent
dispenser
sections.
Use this cycle for loads
with normal amounts of
food soil. (The energy-
usage label is based on
this cycle.)
Use both
detergent
dispenser
sections.
or
NORMAL
WASH
WASH