NuTone CT650 - Manuel (Page 13)

PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION
Cleaner won’t start.
Poor job of dirt pick-up.
Cleaner starts but
cuts off.
Power Brush will not
run when attached.
Constant green light on
in dirt sensor.
Any, some, or all red
light in dirt sensor burn
and never turn green.
No green or red dirt
sensor lights.
Cleaner picks up move-
able rugs or Power
Brush pushes too hard.
Light won’t work.
Cleaner leaves marks
on carpet.
1. Unplugged at wall outlet.
2. Tripped circuit breaker/blown fuse at household
service panel.
3. Loose hose electrical connections.
4. Tripped overload protector in Power Brush
1. Full or clogged dust bag.
2. Clogged airflow passages.
3. Dirty Filters
4. Wrong pile height setting
5. Open suction control
6. Hole in hose
7. Worn Power Brush agitator
8. Worn or broken belt
9. Dirty agitator or end caps
1. Hose electrical connections.
2. Tripped overload protector in Power Brush.
3. Tripped overload protector in Power Unit.
1. Power Brush connections unplugged.
2. Worn or broken belt.
3. Dirty agitator or end caps.
4. Tripped overload protector in Power Brush
1. Dirt passage is clogged.
2. Lenses are dirty.
1. Dirt passage is clogged.
1. No power to sensor board.
1. Wrong pile height setting.
2. Suction too strong.
1. Burned out light bulb.
1. Wrong vacuuming pattern.
1. Plug in firmly, push ON/OFF switch to ON.
2. Reset circuit breaker or replace fuse.
3. Reconnect hose ends.
4. Clean agitator and end caps, then reset
(see page 9, 10, 11).
1. Change bag.
2. Clear airflow passages.
3. Change filters.
4. Adjust setting (page 7).
5. Adjust control (page 9).
6. Replace hose.
7. Change agitator (page 10).
8. and 9. See BELT CHANGING.
1. Check connections, reconnect hose ends.
2. Remove any items that may be caught or
jammed, then reset. If cleaner starts and stops
again, clean agitator and end caps, then reset
(page 9, 10, 11).
3. Change dust bag, clean airflow blockage.
Wait up to 50 minutes for motor to cool and
automatically reset.
1. Plug in firmly.
2. and 3. See BELT CHANGING AND AGITATOR.
CLEANING, (page 10).
4. Check agitator area for excessive lint build-up
or jamming. Clean agitator and end caps and
then reset.
1. Check for clogs in air passages (page 10).
2. Clean lenses (page 8).
1. Check for clogs in air passages (page 10).
1. Take to your nearest NuTone Service Center.
1. Adjust setting (page 7).
2. Open suction control (page 9).
1. Change light bulb (page 11).
1. See VACUUMING TIPS (page 7).
TROUBLESHOOTING
Review this chart to find do-it-yourself solutions for minor performance problems.
Any service needed, other than those described in this owner’s manual, should be
performed by an authorized service representative.
! WARNING Electrical Shock Hazard
Disconnect electrical supply before servicing or cleaning the unit.
Failure to do so could result in electrical shock or personal injury.
▲
!
13
Article Pièce
Ampoule 9123A
Courroie 0518B
PIÈCES ET CARACTÉRISTIQUES
Vous devez bien connaître les pièces et les caractéristiques de votre aspirateur
pour être en mesure de l’utiliser de façon appropriée et sécuritaire. Examinez l’il-
lustration ci-dessous avant d’utiliser l’aspirateur.
Cordon et porte-
cordon
Poignée de
la rallonge
Porte-cordon Cordon d’alimentation
Courroie
Ampoule et lentille
Indicateur de hauteur
de la brosse
Brosses latérales
(non illustrées)
Capteur de saleté
Pédale de réglage de la
hauteur des brosses
Pédale de dégage-
ment de la poignée
Numéro de
modèle/série
(sous l’appareil)
Pédale de dégagement
rapide du manche
4