Panasonic WV-CS954 - Manuel (Page 30)

OFF : In the auto mode, exits the auto mode
when the trigger time elapses.
AUTO (AUTO MODE setting not OFF) : Returns to
the auto mode when the trigger time
elapses.
AUTO (AUTO MODE setting OFF) : Returns to the
home position when the trigger time
elapses.
HOME : Returns to the home position when the
trigger time elapses.
APAN : Activates auto pan when the trigger
time elapses.
SEQ : Activates the sequence function when
the trigger time elapses.
SORT : Activates the sort function when the
trigger time elapses.
PTR 1 to 4 : Activates the patrol function when the
trigger time elapses.
TRK : After the trigger time elapses, the
camera returns to the home position
and then automatic tracking starts.
Following that, after a set time, the
camera returns to the home position
and starts to continue automatic
tracking.
Note: The HOME setting should be selected when
you want to normally leave the camera in the home
position and occasionally perform pan and tilt, or
when you want to activate SEQ.
(5) Auto Mode Setting (AUTO MODE)
Use the auto mode setting to specify the camera
movement mode (OFF, SEQ, SORT, AUTO PAN,
PATROL 1~4, AUTO TRACK).
After selecting AUTO PAN, you can use the AUTO PAN
setting menu to configure detailed settings.
1. Move the cursor to AUTO MODE, and then tilt the
joystick left or right to select a camera movement
mode setting.
OFF
: Manual movement only
SEQ : Sequentially switches between
preset positions in position
number sequence. (sequential
movement)
SORT : Sequentially switches between
preset positions counterclockwise,
starting from the camera home
position. (sort movement)
AUTO PAN : Camera pans automatically within
the range specified by PAN.
Selecting AUTO PAN and pressing
the CAM (SET) button will display
the AUTO PAN setting menu,
which can be used for configuring
detailed settings. (page 31)
PATROL 1 to 4 : Operates the camera in accordance
with patrol function settings.
● Deleting a Preset Position (DEL)
1. Move the cursor to DEL, and then press the CAM
(SET) button.
This deletes the contents of the currently selected
position number and displays the position selection
menu.
(3) Home Position Setting (HOME POSITION)
A currently configured preset position can be
designated as the home position.
Pressing the HOME button of the system controller will
cause the camera to move to the currently specified
home position. Use the following procedure to make a
preset position the home position.
1. Move the cursor to HOME POSITION, and then tilt
the joystick left or right to select the position
number of the preset position you want to make the
home position.
This causes the preset position whose position
number you select to become the home position. If
you do not want to use the home position function,
select OFF for the HOME POSITION setting.
(4) Self Return Setting (SELF RETURN)
The self return setting can be used to specify automatic
return to a particular mode if a certain amount of time
elapses without any operation being performed.
1. Move the cursor to SELF RETURN, and then tilt the
joystick left or right to select a self return trigger setting.
Tilting the joystick cycles through the self return
display in the sequence shown below. (unit: sec,
min)
2. If you selected any setting other than OFF in step 1,
press the CAM (SET) button and then tilt the
joystick left or right to select a self return mode.
-30-
30MIN ↔ 20MIN ↔ 10MIN ↔ 5MIN ↔ 3MIN ↔ 2MIN ↔ 1MIN
OFF ↔ 1S ↔ 2S ↔ 3S ↔ ....... ↔ 10S ↔ 20S ↔ 30S ↔ 40S
60MIN 50S
↔↔ ↔↔
PRESET NO. 1*
POSITION SET
PRESET ID
ALC/MANUAL
AF MODE
DWELL TIME
SCENE FILE
PRESET SPEED
RET TOP DEL
ON
ALC
MANUAL L
10S
OFF
••••••••I
L H
**PRESET POSITION**
2*
6*
10*
14*
18*
22*
26*
30* 3*
7*
11*
15*
19*
23*
27*
31* 4*
8*
12*
16*
20*
24*
28*
32* 1
5*
9*
13*
17*
21*
25*
29*
ID:DOOR
033-064 225-256
RET TOP
OFF ↔ AUTO ↔ HOME ↔ APAN ↔ SEQ ↔ SORT
TRK ↔ PTR4 ↔ PTR3 ↔ PTR2 ↔ PTR1