Samsung DVD-C450K - Manuel (Page 5)

5
Install Batteries in the Remote control
1. Open the battery cover on the back of the remote control.
2. Insert two AAA batteries. Make sure that the polarities (+ and -) are
aligned correctly.
3. Replace the battery cover.
1. DVD POWER Button
Turns the power on or off.
2. REPEAT Button
Allows you to repeat play a
title, chapter, track, or disc.
3. DISC MENU Button
Brings up the Disc menu.
4. BOOKMARK
Quickly find bookmark sec
tions of a DVD.
5. STOP Button ( )
6. SKIP Buttons (
/ )
Use to skip the title, chapter
or track
7. MENU Button
Brings up the DVD player’s
menu.
8. ENTER/π/†,√/® Buttons
This button functions as a
toggle switch.
9. AUDIO Button (√)
Use this button to access
various audio functions on
a disc.
10. INFO Button
Displays the current disc
mode.
11. OPEN/CLOSE ( ) Button
To open and close the disc
tray.
12. REPEAT A-B Button
Allows you to repeat A-B
disc.
13. ZOOM Button
Enlarges the DVD Picture.
14. VIDEO SEL. Button
Selects video output for
mats.
15. SEARCH Buttons ( / )
Allow you to search for
ward/back ward through a
disc.
16. PLAY/PAUSE Button (
)
Begin/Pause disc play.
17. SUBTITLE Button (π)
18. RETURN Button
Returns to a previous menu.
19. TITLE MENU Button (®)
Brings up the Title menu.
20. CANCEL Button
Use to remove menus or
status displays from the
screen.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
18
17
16
19
20
DVD-C350
Connections
Choosing a Connection
The following explains how to make connections commonly used to connect the DVD player with a
TV and other components. A diagram showing these connections is on the next page.
Before Connecting the DVD Player
- Always turn off the DVD player, TV, and other components before you connect or disconnect
any cables.
- Refer to the user’s manual of the additional components you are connecting for more informa-
tion on those particular components.
B. Connecting to a TV (VIDEO)
- Using video/audio cables, connect the
VIDEO (yellow)/AUDIO (red and white) OUT terminals
on the rear of the DVD player to the VIDEO (yellow)/AUDIO (red and white) IN terminals of TV.
- Turn on the DVD player and TV.
- Press the input selector on your TV remote control until the Video signal from the DVD player
appears on the TV screen.
Note
- Noise may be generated if the audio cable is placed too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection section below.
- The number and position of terminals can vary depending on your TV set.
Please refer to the user's manual of the TV.
- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal
of the DVD player.
- If you press the VIDEO SEL. button when DVD Player is in stop mode or no disc is inserted, the
Video Output mode changes in the following sequence: (I-SCAN ➝ P-SCAN ).
A. Connections to a TV Interlace / Progressive
- Connecting through the Component jacks lets you view video at the 480p (Progressive Scan)
resolution.
- What is “Progressive Scan”? Progressive scan has twice as many scanning lines per frame as
interlaced (480i) output and provides better and clearer picture quality.
1.Using Component video cables (not included), connect the COMPONENT VIDEO OUT (PR, PB
and Y) jacks on the rear of the DVD player to the COMPONENT IN (PR, PB and Y) jacks of your
TV.
2. Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the
DVD player to the AUDIO (red and white) IN terminals of TV. Turn on the DVD player and TV.
3. Set the Video Output to I-SCAN/P-SCAN in the Display Setup menu. You can use the VIDEO
SEL. button to change the Video Output mode.
4. Press the input selector on your TV remote control until the Component signal from the DVD
player appears on the TV screen.