Maytag W10160251A - Manuel (Page 19)

19
Stopping, Pausing or Restarting
To stop or pause your dryer at any time
Open the door or press PAUSE/CANCEL once. Press PAUSE/CANCEL twice to cancel a cycle.
To restart the dryer
Close the door. Press START until dryer starts.
NOTE: Drying will continue from where the cycle was interrupted if you close the door and
press Start within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will
shut off. Select new cycle settings before restarting the dryer.
Drying and Cycle Tips
Select the correct cycle and dryness level or temperature for your load. If a Sensor Dry Cycle
is running, the display shows the estimated cycle time when your dryer is automatically
sensing the dryness level of your load. If a Timed Cycle is running, the display shows the exact
number of minutes remaining in the cycle.
Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool
Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down
depends on the load size and dryness level.
Drying tips
■ Follow care label directions when they are available.
■ If desired, add a fabric softener sheet. Follow package instructions.
■ To reduce wrinkling, remove the load from the dryer as soon as tumbling stops. This is
especially important for permanent press, knits and synthetic fabrics.
■ Avoid drying heavy work clothes together with lighter fabrics. This could cause
overdrying of lighter fabrics and lead to increased shrinkage or wrinkling.
Cycle tips
■ Dry most loads using the preset cycle settings.
■ Refer to the Sensor Dry or Timed Preset Cycle Settings chart (in the “Cycles” section) for a
guide to drying various loads.
■ Drying temperature and dryness level are preset when you choose a Sensor Dry
Cycle. You can select a different dryness level, depending on your load, by pressing
Dryness and choosing More, Normal, Less or Damp.
NOTE: You cannot use the Timed Cycle Adjust and you cannot choose a Temperature
with the Sensor Dry Cycles.
■ If you wish to adjust the cycle length of a Timed Cycle, press the Timed Cycle Adjust
up or down arrows. Adjust the temperature of a Timed Cycle by pressing Temp until
the desired temperature is selected.
NOTE: You cannot choose a dryness level with Timed Cycles.
Status Lights
Follow the progress of your dryer with the drying Status indicator lights.
Sensing
■ In a Sensor Dry Cycle, the Sensing light illuminates until a wet item is detected.
■ In a Timed Cycle, the Sensing light illuminates at the beginning of a cycle and turns off
5 minutes into the cycle.
Wet
The Wet light illuminates at the beginning of a Sensor Dry Cycle if a wet item is detected.
■ In a Sensor Dry Cycle, if a wet item is not detected after approximately 5 minutes, the
dryer goes directly into Cool Down. The Cool Down and the Wrinkle Prevent setting
indicators will illuminate, if selected.
■ In a Timed Cycle, wet items are not detected. The dryer will continue to run for the length
of time selected, and the Wet light will illuminate. The damp light will not illuminate.
Damp
The Damp light illuminates in a Sensor Dry Cycle when the laundry is approximately 80%
dry. Damp Dry Chime beeps, if selected. See “Options.”
Cool Down
The Cool Down light illuminates during the cool down part of the cycle. Laundry cools for
ease in handling.
Dry
The Dry light illuminates when the drying cycle is finished. This indicator stays on during the
Wrinkle Prevent setting.
Wrinkle Prevent Setting
The Wrinkle Prevent setting light illuminates when this option is selected. This indicator stays
on during the Wrinkle Prevent setting.
Indicator lights
Other indicator lights show Cycle, Modifiers, Options and Cycle Signal settings selected. The
display shows the estimated or actual time remaining.