Philips Magnavox MSC455 - Manuel (Page 3)

5 5 To exit the
menu.
- 3 - EN
3. Preparation for Use
2 2
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
Hint Hint
• Repeat these steps only if either there
was a power failure or if this unit has been
unplugged for more than 30 seconds.
1 1
Turn on the TV and set
it to channel 3.
• If channel 3 is already occupied for broad-
casting, see “RF Output Channel” section.
STANDBY-ON
STOP PLAY
CH 01
AUTO SET UP
F.FWD
To Select a Channel
You can select a channel by using
the Number buttons on the
remote control.
Notes for using the Number buttons:
• When selecting cable channels
which are higher than 99, enter
channel numbers as a three-digit
number (for example: 117, press
[1], [1], [7]).
• You must precede single-digit
channel numbers with a zero (for
example: 02, 03, 04 and so on).
To Preset the Channel Again
1) Press [MENU] until the main
menu appears.
2) Select "CHANNEL SET UP" by
pressing [PLAY B B ] or [STOP C C ].
Then, press [F.FWD g g ].
3) Select "AUTO SET UP" by
pressing [PLAY B B ] or [STOP C C ].
Then, press [F.FWD g g ]. After
scanning, the tuner stops on the
lowest memorized channel.
To Change the On-Screen
Language
1) Press [MENU] until the main
menu appears.
2) Select "LANGUAGE SELECT" by
pressing [PLAY B B ] or [STOP C C ].
Then, press [F.FWD g g ].
3) Select "ENGLISH", "FRANCAIS"
or "ESPAÑOL" by pressing
[PLAY B
B ] or [STOP C C ]. Then,
press [C.RESET/EXIT].
1 1
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO
[ON]
SAP
MENU
2 2
CHANNEL SET UP
AUTO SET UP
B MANUAL SET UP
STOP PLAY
MANUAL SET UP
CHANNEL 30 (CATV)
ADD
4 4
MANUAL SET UP
CHANNEL 30 (CATV)
DELETE
STOP PLAY
F.FWD
F.FWD
STOP PLAY
F.FWD
1 1
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO
[ON]
SAP
MENU
2 2
CLOCK SET
MONTH DAY YEAR
1 0 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
STOP PLAY
STOP PLAY
F.FWD
F.FWD
3 3
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 – – – –
HOUR MINUTE AM/PM
– – : – – – –
STOP PLAY
F.FWD
4 4
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 2 0 0 5
HOUR MINUTE AM/PM
– – : – – – –
STOP PLAY
F.FWD
5 5
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 MON 2 0 0 5
HOUR MINUTE AM/PM
0 5 : – – – –
STOP PLAY
F.FWD
6 6
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 MON 2 0 0 5
HOUR MINUTE AM/PM
0 5 : 4 0 – –
STOP PLAY
F.FWD
7 7
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 MON 2 0 0 5
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
B PM
STOP PLAY
Hint Hint
• To go back one step, press [REW h h ]
(during steps 2 to 7).
• Your clock setting will be lost if either there
is a power failure or if this unit has been
unplugged for more than 30 seconds.
REW
F.FWD
No No Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
• You can select only the channels memorized
in the unit by using [CHANNEL ].
• If "AUTO SET UP" appears on the TV screen
again, check the cable connections. Then,
press [F.FWD g
g ] once again.
Hint Hint
• If you accidentally select Spanish or
French and need English: Press
[MENU] and choose SELEC. IDIOMA,
or SELECTION LANGUE. Press
[F.FWD g
g ] and select ENGLISH.
Finally, press [C.RESET/EXIT].
Select “ADD” or “DELETE”.
Select the channel to be
added or deleted.
C.RESET
EXIT
Select the current month.
Select the current day.
Select the current year.
Select “AM” or “PM”.
8 8 To exit the CLOCK SET
screen
Select the current hour.
Select the current minute.
Y Y es es Press [MENU] to
exit.
• Refer to “Hint for Cable Box or
Satellite Box” section on page 1. No
Clock Set Up To Add/Delete Channels Turn on the Unit for the First Time
TV Screen Remote Control
F.FWD
• If the clock is not set, the
CLOCK SET screen
appears when you press
[MENU]. In this case, go
to step 2).
or
or
or
or
or
or
or
or
or
or
or
or
Do you connect the cable from the cable box
or the satellite box to the VCR’s ANT-IN jack?
Yes
3 3
3 3
HJ440CD_EN.QX33 05.7.5 9:59 AM Page 3