Philips HP6409 - Manuel (Page 3)

6 Dry the attachment before you use or store it.
Cleaning the epilating head
1 Switch off the appliance.
2 Remove the adapter from the wall socket (1)
and pull the appliance plug out of the appliance
(2) (Fig. 19).
3 Push the epilating head in the direction of the
arrow (1) and remove it from the appliance
(2) (Fig. 12).
4 Remove loose hairs with the cleaning
brush (Fig. 21).
5 Rinse the epilating head under the tap for 5-10
seconds while turning it (Fig. 22).
6 Shake the epilating head firmly and dry it
thoroughly with a tea towel (Fig. 23).
Note: Make sure the epilating head is completely dry before
you place it back onto the appliance.
Cleaning the shaving head
1 Switch off the appliance.
2 Remove the adapter from the wall socket (1)
and pull the appliance plug out of the appliance
(2) (Fig. 19).
3 Push the shaving head in the direction of the arrow
(1) and remove it from the appliance (2). (Fig. 24)
4 Remove the shaving foil from the shaving
head (Fig. 25).
5 Clean the shaving foil, the cutter block and the hair
chamber with the cleaning brush.
Do not exert any pressure on the shaving foil to avoid
damage.
6 You can also rinse the shaving head and its parts
under the running tap.
7 Put the protection cap on the shaving head after
use.
8 Rub a drop of sewing machine oil onto the shaving
foil twice a year.
Replacement
If you use the appliance two or more times a week, we
advise you to replace the shaving foil and the cutter block
every 1 to 2 years.
A worn or damaged shaving foil may only be replaced
with an original Philips shaving foil (type no. HP6116).
A worn or damaged cutter block may only be replaced
with an original Philips cutter block (type no. HP2911).
Environment
Do not throw away the appliance with the normal
household waste at the end of its life, but hand it in
at an official collection point for recycling. By doing
this, you help to preserve the environment (Fig. 26).
Guarantee & service
If you need information or if you have a problem, please
visit the Philips website at www.philips.com or contact the
Philips Customer Care Centre in your country (you find
its phone number in the worldwide guarantee leaflet).
If there is no Customer Care Centre in your country,
go to your local Philips dealer or contact the Service
Department of Philips Domestic Appliances and Personal
Care BV.
Troubleshooting
If the appliance does not work or does not work
properly, first check the list below. If the problem is not
mentioned in this list, the appliance probably has a defect.
In that case we advise you to take the appliance to your
dealer or to an authorised Philips service centre.
Problem Cause Solution
Poor
epilating
results.
You move
the epilator in
the wrong
direction.
Move the appliance
against the direction
of hair growth, with
the on/off slide
pointing in the
direction in which you
move the appliance.
-
Problem Cause Solution
You place
the epilating
head on the
skin at the
wrong angle.
Make sure that you
place the appliance
perpendicularly onto
the skin (see chapter
‘Using the appliance’).
You used a
(depilatory)
cream prior to
epilation.
Make sure your skin
is clean, entirely dry
and free from grease.
Do not use any cream
before you start
epilating.
Make sure that the
hairs to be removed
have a length of
at least 3mm to
guarantee proper hair
removal.
The
sensitive area
cap is on the
epilating head
when you
epilate your
legs.
Do not use the
sensitive area cap
when you epilate
your legs, as the cap
reduces the number
of active epilating
discs. NB: Never use
the epilator without
the precision cap
when you epilate your
underarms or bikini
line.
The
appliance
does not
work.
The socket
to which the
appliance is
connected is
not live.
Make sure the
socket is live. If you
have connected
the epilator to the
socket in a bathroom
cabinet, you may
need to switch on
the bathroom light to
activate the socket.
420300059351 3/5