haier CWH08A - Manuel (Page 11)

11
■ Auto—automatically controls the fan speed depending on
the current room temperature and temperature control
setting
NOTE: Auto fan speed cannot be selected in Fan mode.
NOTE: After 5 seconds, the display will show the current room
temperature.
Filter Monitor
1. When the Filter Monitor indicator light is lit, remove, clean and
replace the air filter. See “Cleaning the Air Filter.”
2. Press and hold FILTER MONITOR for 3 seconds after
replacing the air filter. This resets the filter monitor.
Temperature
■ Press the plus TEMP button to raise the temperature. Each
time you press or hold the plus TEMP button, the
temperature will go up 1ºF (1ºC) until it reaches 90°F (32°C).
NOTE: After 5 seconds, the display will show the current
room temperature.
■ Press the minus TEMP button to lower the temperature. Each
time you press or hold the minus TEMP button, the
temperature will go down 1°F (1°C) until it reaches 64°F (18°C).
NOTE: After 5 seconds, the display will show the current room
temperature.
Timer Delay
To set the Timer for a 30-minute to 24-hour delay until the
air conditioner turns off (the air conditioner must be On):
1. Press TIMER. Timer indicator light will flash. Display will show
remaining hours before the air conditioner will turn off.
2. Press the plus or minus TEMP button to change the delay
time from 30 minutes to 24 hours.
3. After 5 seconds, Timer indicator light will remain on. Display
will show the current room temperature.
To set the Timer to turn on the air conditioner, keeping
previous settings:
1. Turn off air conditioner.
2. Press TIMER. Timer indicator light will flash. Display will show
remaining hours before the air conditioner will turn on.
3. Press the plus or minus TEMP button to change the delay
time from 30 minutes to 24 hours.
4. After 5 seconds, Timer indicator light will remain on. Display
will show current room temperature.
To set the Timer to turn on the air conditioner, changing
previous settings:
1. Turn on air conditioner.
2. Adjust the mode to Cool, Dry, Fan, Heat (Heat/Cool models
only) or Power Saver.
3. For Cool, Fan, Heat (Heat/Cool models only) or Power Saver
mode, adjust fan speed to High, Med, Low or Auto.
Adjust temperature between 64ºF and 90ºF (18ºC and 4.
NOTE: In Fan and Dry mode, temperature cannot be
To clear Timer delay program:
NOTE: Air conditioner can be either on or off.
1. Press TIMER once after it has been programmed. Display will
show remaining time.
2. While the display is showing the remaining time, press TIMER
again. Timer indicator light will turn off.
To see or change the remaining time (in hours):
1. Press TIMER once after it has been programmed. Display will
show remaining time.
2. While the display is showing the remaining time, you can
press the plus or minus TEMP button to increase or decrease
the time.
3. After 5 seconds, the display will show the current room
temperature.
To change the temprature display from °F to °C:
NOTE: After 360 hours of fan operating time, the Filter indicator
light will turn on. It will remain on for 180 hours or until you press
FILTER MONITOR. After 180 hours, the Filter indicator light will
turn off automatically.
NOTE: Auto fan speed cannot be selected in Fan mode.
32ºC).
adjusted.
5. Wait 3 seconds before turning off air conditioner.
6. Press TIMER. Timer indicator light will flash. Display will show
remaining hours before air conditioner will turn on.
7. Press the plus or minus TEMP button to change delay time
from 30 minutes to 24 hours.
8. Press TIMER again or wait 5 seconds. Timer indicator light
will remain on. Display will show current room temperature.
Press both the plus and minus TEMP buttons at the same time to
switch the display from ºF to ºC.