Swiss+Tech Portable Light Pods - Manuel

(B)
Pod
“ON” Button
Antenna
Hook-and-Loop
Mounting
Strap
Limited One Year Warranty
This product is covered by a limited one year warranty
to the original purchaser in that this product is free
from defects in workmanship and materials. During
the warranty period, these products will either be
repaired or replaced with a product of equal or greater
value, excluding any custom engraving or printing.
Damage through normal wear and tear (including
battery expiration and surface coatings), repair or
alteration, misuse, abuse, neglect, accident, improper
storage and handling, fire, negligence, improper
cleaning, circumstances not directly attributable to
manufacturing defects, or act of God is not included.
THIS WARRANTY IS IN LIEU OF ALL OTHER WAR-
RANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO, IMPLIED WARRANTY OF MERCHANT-
ABILITY OR FITNESS FOR A PARTICULAR USE.
This warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state. Simply return your SWISS+TECH ® brand product
postpaid and insured to:
Swiss+Tech Products
30725 Solon Industrial Pkwy
Solon, OH 44139
Made in China. MMMMMMMMI ™ and MI ® are
trademarks of Swiss+Tech Products. Specifications
are subject to change without notice.
©2014 Swiss+Tech Products, Solon, OH 44139 USA
Portable Light Pod
System
Pod Battery Replacement
1. Unscrew and remove Phillips screw.
2. Unscrew lens (1/4-inch turn) and remove
black base.
3. Remove old batteries, replace with 2 new
CR2450 or equivalent. Position positive
sides (+) to face the LED bulbs.
4. Reposition base on batteries/LED/lens
assembly, turn 1/4-inch to lock in place.
5. Replace Phillips screw, tighten gently.
2. Remove Battery
Saving Disk (B)
a. Unscrew and
remove
Phillips screw.
b. Rotate lens
(1/4-inch turn)
and remove
black base.
c. Remove battery
saving disk.
d. Reposition base on
batteries/LED/lens
assembly, turn
1/4-inch to lock
in place.
e. Replace Phillips
screw, tighten
gently.
1. Remove Remote PULL Tab (A)
(Allows battery to function.)
Remote Battery Replacement
1. Unscrew 2 Phillips screws (captive screws
remain in back cover to prevent loss).
2. Carefully lift off back cover.
3. Slide out old batteries, replace with 2 new
CR2032 or equivalent. Position positive
sides (+) up.
4. Replace back cover, tighten screws gently.
than 10 minutes and also allows lights to
activate along chosen route as you walk.
• Pod lights and pulse mode can be turned off
manually at any time using the Remote
“OFF” button.
• Pressing the “PULSE” button while in pulse
mode deactivates pulse mode and will revert
to timer mode.
Adding Pods & Remotes
• Press and hold the Pod “ON” Button for
3 seconds to turn on its Learning Mode
(Pod will flash 3 times rapidly, then stay on
and in learning mode for 10 seconds).
• During the 10 seconds, press the Remote
“ON” button while in range of the Pod. The
Pod will flash once to confirm that learning
has occurred.
• If adding multiple light pod sets together,
one remote can operate an unlimited amount
of light pods. Each light pod however, can
only be operated by up to 3 different
remotes.
3. Prepare for Installation
a. Activate a Pod by pressing its “ON” button
(light goes on).
b. Then turn off Pod light using Remote “OFF”
button. Pod light can now be turned on and
off with the Remote.
4. Installation
• Install activated pods along your chosen
route using the hook-and-loop straps as
shown in above image. Suggested distance
between Pods is 300 ft with unobstructed
ST74152
10" x 6" folds to 2" x 1.5"
ENGLISH SIDE
Two CR2032
Batteries
“+” Side Up
ON OFF PULSE REMOTE
POD
Pull Tab (A)
view. Mount approximately 6 ft high
for best results.
Remote “ON” Button Use
(Timer Mode)
• When Remote “ON” button is pressed, all
activated Pods in range will light up.
• Pod lights will stay on for 10 minutes.
• Pod lights can be turned off at any time
using the Remote “OFF” button.
Remote “PULSE” Button Use
(Sensor Mode)
• Pressing the remote “PULSE” button will
transmit a signal every minute for
40 minutes, providing continuous light for
50 minutes. Each pulse turns on or keeps
on all Pod lights within range. (Remote
red LED flashes every 5 seconds to
confirm pulse mode is active).
• The PULSE button allows for continuous
light when desired stay in area is longer
*To save battery when storing,
press button on back of Pod while
Pod is lit. Light will flash rapidly
to confirm off mode.
swisstechtools.com
1-800-414-8799
This product contains button batteries.
IF SWALLOWED, batteries could cause
severe injury or death in just 2 hours.
SEEK MEDICAL ATTENTION IMMEDIATELY.
• Always purchase the correct size and grade
of battery most suitable for the intended use.
• Clean the battery contacts and also those
of the device prior to battery installation.
• Ensure the batteries are installed
correctly with regard to polarity (+ and -).
• Remove batteries if they are spent or if
product is unused for long periods of time.
• Always replace the whole set of batteries
at one time. DO NOT mix old and new.
• DO NOT MIX batteries of different types,
such as Alkaline, Standard (carbon-zinc)
and/or Rechargeable (nickel-cadmium).
BATTERY WARNINGS:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired operation.
Watch DEMO VIDEO online:
swisstechtools.com/lightpod
Weather
Resistant
8m Beam
Distance
10-12
Lumens
Two CR2450
Batteries
“+” Side
Down