Philips SCF271-07 - Manuel (Page 4)

Loading one VIA Feeding System and up to four
6oz/180ml OR 8oz/240ml VIA Cups and Lids*
1. Position the nipple in an outer nipple cavity.
2. Place the screw ring over the nipple.
3. Position the VIA Cups upside down around
the dome cap stem.
4. Place the VIA Adaptor on its side around the
racks edge (as shown).
5. Position the VIA Lids vertically around the racks
edge. Rims should face out for easier loading.
6. Place the dome cap in the unobstructed upper
slot of the dome cap stem.
To load the AVENT Tempo Natural Feeding Nurser
1. Open the inner locking ring of the screw ring and place
the screw ring in the basket with the locking tab
facing downwards. Ensure that the parts of the screw
ring that are in contact with the nipple are facing
upwards.
2. Place the nipple and the dome cap in the basket as
you would when sterilizing a bottle assembly.
3. Follow sterilizing instructions.
Loading other feeding and baby product items
When sterilizing other NON-ELECTRICAL Philips AVENT
PRODUCTS simply place the components in the rack allowing
enough space so that steam can effectively circulate.
EN
After each cycle
IMPORTANT: Allow the unit to cool for at least two
minutes before removing the sterilizer from the
microwave.
1. Removing the sterilizer from the microwave: After
the unit has cooled, remove it from the microwave
by holding the skirt and/or safety grips and then
place on an even, heat-resistant surface.
NOTE: Items will remain sterile in the Microwave Steam Sterilizer for
up to 24 hours providing the lid is not removed.
2. After removing the sterilizer from the microwave:
Remove the lid by unlocking the clips – When removing
the lid, point it away from you to allow steam to escape.
Care and cleaning
• Always drain the excess water from the unit and
rinse to prevent the build up of limescale.
• Always store when completely dry.
• The Microwave Steam Sterilizer is dishwasher safe.
WARNINGS –
FAILURE TO FOLLOW INSTRUCTIONS MAY CAUSE
SCALDING OR DAMAGE TO THIS PRODUCT AND/OR
YOUR MICROWAVE
• Always ensure you use 200ml of water before
sterilizing. (The unit should be emptied of
residual water before each subsequent use.)
• Always follow loading instructions and
do not overload.
• Do not use bleach or chemical sterilizing solutions/
tablets in sterilizer or on products to be sterilized.
• Do not sterilize metallic or electronic items
in the sterilizer.
• Do not microwave bottle brush.
• Always use the appropriate heating time for the
power of your microwave unit. (see Table )
• In combination ovens, ensure grill is switched off
and has cooled before use.
• Be sure that the lid is properly fastened to the
base before placing in microwave.
• Always allow at least 2 minutes cooling time
before removing from the microwave.
• Do not remove the lid from the sterilizer
immediately after cycle. Allow to cool as the
steam will be hot.
• When removing from microwave, be sure to
hold the sterilizer level to avoid leaking or
spilling of hot water.
• When taking the sterilizer out of the microwave,
BE CAREFUL – it will still be hot.
• When removing the lid, point it away from you
to allow steam to escape.
• Be careful when handling the sterilized products
as they may be hot.
• Always keep out of reach of children.
NOTE: Do not overload the sterilizer.
NOTE: Do not place dome caps in the sterilizer upside down.
NOTE: The Microwave Steam Sterilizer is designed to
specifically hold the wide shape of AVENT Feeding
Bottles.
Some products featured may not be available in all
countries. Please contact Philips AVENT to check availability.
Philips AVENT is here to help
1.800.54.AVENT
www.philips.com/AVENT
In US manufactured for Philips Consumer Lifestyle,
a division of Philips Electronics North America
Corporation. 1600 Summer Street,
5 Fl., Stamford, CT 06905-5125
In Canada imported for Philips Electronics Ltd,
281 Hillmount Road, Markham, ON L6C2S3
IV
E
III
* Consists of VIA Cup, Lid and Adaptor, an Extra Soft Slow Flow Nipple, Dome Cap and Screw Ring
F
Philips AVENT Microwave Steam Sterilizer EN
Loading the sterilizer
Assembly and Use
Before using the Microwave Steam Sterilizer, always
ensure that the items are positioned according to the
below loading instructions.
Loading six 4oz/125ml or 9oz/260ml
AVENT Feeding Bottles
1. Position the nipples in the nipple cavities around
the dome cap stem.
2. Place the screw rings over the nipples.
3. Place the first three dome caps in the lower slots
of the dome cap stem.
4. Place the remaining three dome caps in the upper
slots of the dome cap stem.
5. Position the bottles upside down around the
previously loaded nipples and screw rings.
Loading three 11oz/330ml AVENT Feeding Bottles
1. Position the nipples in the three nipple cavities
surrounding the dome cap stem.
2. Place the screw rings over the nipples.
3. Position the bottles upside down in the three
outer nipple cavities.
4. Arrange the three dome caps around the edge
of the rack in between the inverted bottles.
Loading one or two Philips AVENT Breast
Pumps (non-electrical components only) and
two 4oz/125ml OR two 9oz/260ml AVENT
Feeding Bottles
1. Disassemble the Breast Pump ensuring
the stem is removed from the diaphragm.
2. Position the Breast Pump bodies into the
two slots provided.
3. Position the nipples in the nipple cavities
around the dome cap stem.
4. Place the screw rings over the nipples.
5. Place one dome cap in the unobstructed lower
slot of the dome cap stem, then the second in
the upper slot on top of the inserted dome cap.
6. Position the bottles upside down in the
unobstructed bottle cavities.
7. Place the remaining NON-ELECTRICAL pump
components in any unobstructed space on the rack.
Loading six 6oz/180ml OR 8oz/240ml VIA
Cups and Lids
1. Position the VIA Cups upside down around the
dome cap stem.
2. Position the VIA Lids vertically around the racks
edge. Rims should face out for easier loading.
A
B
D
C
Contents
1. Lid
a. Clips
2. Bottle/Accessories Rack
b. Dome cap stem
c. Bottle cavity
d. Nipple cavity
e. Breast Pump slots
3. Base
f. Safety grips
Before each use
Wash all items in warm
soapy water and then rinse
in water.
Wash your hands before
handling your sterilized
products.
1. Remove rack from the
sterilizer and pour 200ml
of water into the base.
IMPORTANT: Failure to add
enough water may cause
damage to the Microwave
Steam Sterilizer and/or your
microwave. Adding too much
water may mean your items are
not properly sterilized.
2. Put the rack back into the base.
3. Position the lid over the
sterilizer base and lock the
clips into place until you
hear them “click”.
4. Ensure that the microwave
is clean and dry before use
– Place the sterilizer into the
center of the microwave.
Select microwave wattage
and timings – See Table III
– do not exceed these times.
I
II
Please take a few minutes to read through
the ENTIRE INSTRUCTION LEAFLET including
the warnings before using your Microwave
Steam Sterilizer for the first time. PLEASE
RETAIN THESE INSTRUCTIONS. Also available
at www.philips.com/AVENT
Thank you for
choosing Philips AVENT
Now you can enjoy the convenience
and ease of using the Philips AVENT
Microwave Steam Sterilizer, which
effectively eliminates harmful
bacteria in just minutes! Its large
capacity holds more than any
other microwave sterilizer – up to
six bottles – yet it is compact and
lightweight enough for travel.
Advanced features such as cool
safety grips aid in safe handling
and make it easier than ever to
sterilize Philips AVENT Breast
Pumps, Bottles, Cups and more.
III
9 8