Philips AZ1004-17B - Manuel

AZ AZ1004 CD Soundmachine
Need help? Call us!
Philips representatives are ready to help you
with any questions about your new product.
CALL US BEFORE YOU CONSIDER
RETURNING THE PRODUCT!
1-800-531-0039
or visit us on the web at www.philips.com
S E E W HY INS I D E
IM
PO RTAN
T ! Return
your Warranty
Registration Card
within 10 days
PHILIPS CONSUMER ELECTRONICS NORTH AMERICA
Knoxville, Tennessee 37914-1810, U.S.A.
Printed in China
W
CLASS 1
LASER PRODUCT
AZ1004
English
F rançais
Español
English:This digital apparatus does not exceed the Class B limits for radio noise emis-
sions from digital apparatus as set out in the Radio Interference Regulations of the Cana-
dian Department of Communications.
Français: Cet appareil numérique n'émet pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de Classe B prescrites dans le Règlement sur
le Brouillage Radioélectrique édicté par le Ministère des Communications du Canada.
Meet Philips at the Internet
http://www.philips.com
YMT/417
User Manual
Manuel d'utilisation
Manual del usario
Canada
The set complies with the FCC-Rules, Part 15 and with 21 CFR
1040.10. Operation is subject to the following two conditions:
1.This device may not cause harmful interference, and
2.This device must accept any interference received, including inter-
ference that may cause undesired operation.
L’appareil répond aux normes FCC, Part 15 et 21 CFR 1040.10.
Fonctionnement soumis aux deux conditions suivantes :
1. Cet appareil ne doit pas provoquer d’interférences nuisibles, et
2. Cet appareil doit accepter toute interférence reçue, y compris les
interférences susceptibles de provoquer un fonctionement peu satis-
faisant.
El aparato cumple las normas FCC, Parte 15 y 21 CFR 1040.10.
Funcionamiento dependiente de dos condiciones siguientes:
1. Este aparato no puede provocar interferencia dañina, y
2. Este aparato debe aceptar cualquier interferencia recibida,
incluyendo las interferencias que pueden provocar un fun-
cionamiento insuficiente.
6 x R14 • UM-2 • C-CELLS
%
#
$
0 9 ! 8 7
4 3 2 1 5
6 @
1
A A B C
X
2
3
7
4
prog
5
prog
6
Recording from the Radio
1 Adjust the source selector to TUNER to
select your desired waveband.
2 Tune to the desired radio station (see Tuner
reception).
3 Press 9/ to open the cassette holder. Insert
a blank tape and close the deck.
4 Press 0 to start recording.
5 For brief interruptions press ;.To resume
recording, press ; again.
6 To stop recording, press 9/.
Precautions & General
Maintenance (See
7)
• Place the set on a hard and flat surface so
that the system does not tilt.
• Do not expose the set, batteries, CDs to
humidity, rain, sand or excessive heat caused
by heating equipment or direct sunlight.
• Do not cover the set. Adequate ventilation
with a minimum gap of 6 inches between the
ventilation holes and surrounding surfaces is
necessary to prevent heat build-up.
• The mechanical parts of the set contain
self-lubricating bearings and must not be oiled
or lubricated.
• To clean the set, use a dry cloth. Do not use
any cleaning agents containing alcohol,
ammonia, benzene or abrasives as these may
harm the housing.
Tape deck maintenance (See 7)
To ensure quality recording and playback of
the tape deck, clean parts A, B and C as
shown, once a month. Use a cotton bud
slightly moistened with alcohol or a special
head cleaning fluid to clean the deck.
1 Open the cassette holder by pressing 9/.
2 Press 1 and clean the roller C.
3 Press ; and clean the heads A, and the
capstan B.
4 After cleaning, press 9.
➜ Cleaning of the heads can also be done by
playing a cleaning cassette through once.
CD player and CD handling (See 7)
• If the CD player cannot read CDs correctly,
use a cleaning CD to clean the lens before
taking the set to repair.
• The lens of the CD player should never be
touched!
• Sudden changes in the surrounding
temperature can cause condensation on the
lens of your CD player. Playing a CD is then
not possible. Do not attempt to clean the
lens but leave the set in a warm environment
until the moisture evaporates.
• Always close the CD-tape door to avoid dust
on the lens.
• To clean the CD, wipe in a straight line from
the center towards the edge using a soft,
lint-free cloth. Do not use cleaning agents as
they may damage the disc.
• Never write on a CD or attach any stickers
to it.
Problem
– Possible cause
• Remedy
No sound /power
– Volume not adjusted
• Adjust the VOLUME
– Power cord not securely connected
• Connect the AC power cord properly
– Batteries dead/ incorrectly inserted
• Insert (fresh) batteries correctly
– CD contains non-audio files
• Press PREVIOUS, NEXT
∞ , § once or
more to skip to a CD audio track, instead of the
data file.
Display does not function properly/ No
reaction to operation of any of the con-
trols
– Electrostatic discharge
• Switch off and unplug the set. Reconnect after a
few seconds
The CD skips tracks
– CD damaged or dirty
• Replace or clean CD
– Program is active
• Quit program mode
no/Er indication
– No CD inserted
• Insert a CD
– CD badly scratched or dirty
• Replace/ clean CD, see Maintenance
– Laser lens steamed up
• Wait until lens has cleared
– CD-R(W) is blank or not finalized
• Use a finalized CD-R(W) or suitable CD Audio
disc only
Poor cassette sound quality
– Dust and dirt on the heads, etc.
• Clean deck parts, see Maintenance
– Use of incompatible cassette types (METAL or
CHROME)
• Only use NORMAL (IEC I) for recording
Recording does not work
– Cassette tab(s) may be broken
• Apply adhesive tape over the missing tab space
Top and front panels (See 1)
1 VOLUME – to adjust volume level
2 Source selector : CD,TUNER,
TAPE/ POWER OFF
– selects CD, tuner or tape source of sound
– power off switch
3 CD door
4 TUNING – tunes to radio stations
5 BAND – selects waveband
6 PREVIOUS, NEXT ∞ , §
– skips or searches a passage/track
backwards or forward
7 PROG – programs and reviews
programmed track numbers
8 Cassette recorder keys:
; – pauses playback or recording
9/ – stops the tape;
– opens the cassette holder
5 or 6 – fast winds/ rewinds tape
1 – starts playback
0 – starts recording
9 Cassette door
0 CD Display – shows the CD functions
! PLAY/PAUSE 2; - starts or pauses CD
playback.
@ STOP 9 – stop playback;
– erases a CD program.
Back panel
# Telescopic antenna - improves FM
reception.
Note: AM band antenna is built into set
(see Tuner reception)
$ Battery door - open to insert 6 x 1.5V
R-14/ UM2/ C-cells.
% AC POWER/MAINS - inlet for power
cord.
CAUTION
Use of controls or adjustments or
performance of procedures other
than herein may result in hazardous
radiation exposure or other unsafe
operation.
Power Supply
Whenever convenient, use the AC power
supply cord if you want to conserve battery
life. Make sure you remove the plug from the
set and wall outlet before inserting batteries.
Batteries (not included)
1 Open the battery compartment and insert
six batteries, type R-14, UM-2 or C-cells,
(preferably alkaline) with the correct polarity
as indicated by the "+" and "–" symbols inside
the compartment. (See 1)
2 Replace the compartment door, making sure
the batteries are firmly and correctly in place.
The set is now ready to operate.
Batteries contain chemical
substances, so they should be
disposed of properly.
Incorrect use of batteries can cause
electrolyte leakage and will corrode the
compartment or cause the batteries to burst:
• Do not mix battery types: e.g. alkaline with
carbon zinc. Only use batteries of the same
type for the set.
• When inserting new batteries, do not try to
mix old batteries with the new ones.
• Remove the batteries if the set is not to be
used for a long time.
Using AC Mains
1 Check if the AC power supply voltage, as
shown on the type plate located on
the bottom of the set, corresponds to
your local power supply. If it does not, consult
your dealer or service center.
2 Connect the power cord to the AC
POWER/MAINS inlet and the wall socket.The
mains lead is now connected and ready for
use.
3 To switch the set off completely, withdraw the
power cord from the wall socket.
• Disconnect the AC power cord from the wall
socket to protect your set during heavy
thunderstorms.
The type plate is located on the bottom
of the set.
Switching POWER on/off:
Save energy
To avoid unnecessary energy consumption,
always adjust the source selector to
TAPE/
POWER OFF after using the set. Also
check that the tape deck keys are released.
General operation
1 To select your sound source adjust the
source selector to : CD, TUNER or
TAPE/ POWER OFF .
2 Adjust the sound with the VOLUME
control.
3 To switch off the set, adjust the source selec-
tor to TAPE/
POWER OFF position and check
the cassette keys are released.
Tuner reception
1 Adjust the source selector to TUNER.
2 Adjust BAND to select your desired wave-
band.
3 Turn TUNING to tune to a station.
• For FM band signals, extend and turn the
telescopic antenna for best reception. Reduce
its length if the signal is too strong.
• For AM band signals, the set uses a built-in
antenna. Direct this antenna for best recep-
tion by turning the whole set.
4 To switch off the radio, adjust the source
selector to TAPE/
POWER OFF position and
check the cassette keys are released.
CD Player
Display indication for CD
functions:
– --: (See 2) reading disc contents
– no/Er: (See 3) no disc/ error in CD
operation or CD/ CD-R(W) is blank or
not finalized (see Troubleshooting)
– Playback on pause : 2 and current track
number flash (See 4).
– prog: when CD program is active
English Controls/Power Supply Power Supply General operation/Tuner
Playing a CD
This CD player plays Audio Discs including
CD-Recordables and CD-Rewritable.
• MP3 CD-ROMs, CD-I, CDV,VCD, DVD or
computer CDs are not possible for playback
on this set.
1 Adjust the source selector to CD.
2 Insert a CD/ CD-R(W) with the printed side
facing up and press the CD door gently
close.
➜ Display shows -- and later, the total num-
ber of tracks.
3 Press PLAY/PAUSE 2; on the set to start
playback.
4 To pause playback press PLAY/PAUSE 2;.
Press PLAY/PAUSE 2; again to resume
play.
5 To stop CD play, press STOP 9.
6 To switch off the set, adjust the source
selector to TAPE/
POWER OFF position and
check the cassette keys are released.
Helpful hints : CD play will also stop when:
- you open the CD compartment;
- you select TUNER or TAPE/
POWER OFF
sound source;
- the CD has reached the end of playback.
Selecting a different track
During playback you can use ∞ / § to select
a particular track.
- If you have selected a track number in the stop
or pause position, press PLAY/PAUSE 2; to
start playback.
• Press § once briefly for the next track, or
press repeatedly until the desired track num-
ber appears in the display.
• Press ∞ once briefly to return to the begin-
ning of a current track.
• Press ∞ repeatedly for a previous track.
Finding a passage within a
track
1 During playback, press and hold down ∞ /
§.
• The CD is played at high speed and low vol-
ume.
2 When you recognize the passage you want
release
∞ / §.
• Normal playback resumes.
Helpful hints : When searching within a final
track and you reach the end of the last track,
the CD goes to stop mode.
Programming track
numbers
You may store up to 20 tracks in the desired
sequence. If you like, store any track more
than once.
1 In the stop position, press PROG to activate
programming.
➜ Display shows 01 briefly, indicating the
start of the program. Then, prog and 00
flash. (See 5)
2 Press ∞ or § to select your desired track
number.
3 Press PROG to store the desired track
number.
➜ Display shows 02 briefly (up to 20 in
sequence. see 6), indicating the next
program location available. Then, prog
and 00 flash.
4 Repeat steps 2 to 3 to select and store all
desired tracks in this way.
5 To play your program, press PLAY/PAUSE
2;.
Helpful hints : If you store more than 20
tracks, the display will show the 1st track in
the program (01 appears briefly and then, the
track number is displayed). At this time, you
can still store a new track, but the new track
will replace the 1st track in the program.
To review a program
• In the stop position, press PROG repeatedly
to see your stored track numbers.
➜ Display first shows the number of program
location and then, the number of the track
stored here.
Erasing a program
You can erase the contents of the memory
by:
– selecting TUNER or TAPE/
POWER OFF
sound source;
– opening the CD door;
➜Display: prog disappears.
Cassette playback
1 Adjust the source selector to
TAPE/
POWER OFF .
2 Press 9/ to open the cassette holder and
insert a cassette and close the deck.
3 Press 1 to start playback.
4 To pause playback press ;.To resume, press
the key again.
5 By pressing 5 or 6 , fast winding of the
tape is possible in both directions. To stop
fast winding, press
9/
6 To stop the tape, press 9/.
The keys are automatically released at the end
of a tape and the set switched off (unless
PAUSE mode ; has been activated.)
General information on recording
• Recording is permissible insofar as copyright
or. other rights of third parties are not
infringed.
• For recording, use only NORMAL type cas-
settes (IEC type I) on which the tabs have
not yet been broken.This deck is not suited
for recording on CHROME (IEC II) or
METAL (IEC IV) type cassettes.
• The best recording level is set automatically.
Altering the VOLUME will not affect the
recording.
• To protect a tape from accidental erasure,
break out the tabs. If you wish to record
again, cover the tabs with a piece of adhesive
tape.
Synchro Start CD recording
1 Select CD source.
2 Insert a CD and if desired, program track
numbers.
3 Press 9/ to open the cassette holder. Insert
a blank tape and close the deck.
4 Press 0 to start recording.
➜ Playing of the CD program starts auto-
matically from the beginning of the pro-
gram. It is not necessary to start the CD
player separately.
5 For brief interruptions press ;.To resume
recording, press ; again.
6 To stop recording, press 9/.
Helpful hints : To synchro start recording an
entire CD from 1st track, make sure the CD
player has finished reading the CD content
before you press
0 to start recording.
CD Player CD Player Cassette Recorder
Cassette Recorder Maintenance Troubleshooting
Environmental information
All unnecessary packaging material has been omitted.The packaging can be easily separated
into three materials: cardboard, polystyrene and plastic.
Your set consists of materials which can be recycled if disassembled by a
specialized company. Please observe the local regulations regarding the
disposal of packaging, dead batteries and old equipment.
If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service center.
WARNING: Do not open the set as there is a risk of electric shock. Under no cir-
cumstances should you try to repair the set yourself, as this will invali-
date the warranty.
Retournez rapidement votre carte
d’enregistrement de garantie pour profiter
pleinement de votre achat.
L’enregistrement de votre modèle auprès de PHILIPS confirme votre éligibilité à tous les bénéfices
mentionnés ci-dessous. N’oubliez donc pas de remplir votre carte d’enregistrement de garantie et de
nous la retourner le plus tôt possible afin d’assurer :
*Preuve d’achat
Retournez la carte
d’enregistrement ci-incluse
afin de garantir que la date
d’achat de votre produit sera
classée dans nos dossiers et
éviter ainsi le besoin de remplir
d’autres formulaires afin
d’obtenir votre service de
garantie.
*Avis sur la
sécurité des
produits
En enregistrant votre produit,
vous serez avisé - directement
par le fabriquant - de toutes
défectuosités compromettant
la sécurité ou de tout retrait
du produit du marché.
*Bénéfices
additionnels de
l’enregistrement
du produit
L’enregistrement de votre
produit garantit que vous
bénéficierez de tous les
privilèges auxquels vous avez
droit y compris des
offres-rabais spéciales.
Sachez reconnaître ces
symboles de sécurité
Ce symbole « d’éclair »
s’applique aux matériaux non
isolés présents dans votre
appareil et pouvant causer un
choc électrique. Pour assurer la sécurité
des membres de votre famille, veuillez ne
pas enlever le couvercle de votre produit.
Les « points d’exclamation » ont
pour but d’attirer votre attention
sur des caractéristiques à propos
desquelles vous devez lire soigneusement
la documentation accompagnant l’appareil
afin d’éviter tout problème d’exploitation
ou d’entretien.
AVERTISSEMENT : Afin de réduire les
risques d’incendie ou de choc électrique, ne
pas exposer cet appareil à la pluie ou à l’hu-
midité et les objets remplis de liquide,
comme les vases, ne doivent pas être placés
sur le dessus de l’appareil.
ATTENTION : Pour éviter les chocs
électriques, introduire la lame la plus
large de la fiche dans la borne
correspondante de la prise et pousser à
fond.
s t AVIS
RISQUE DE CHOCS ÉLECTRIQUES NE PAS OUVRIR
Attention: Afin de prévenir le risque de chocs électriques ne pas retirer les vis. Toute réparation devrait être confiée à un personnel qualifié.
À l’usage du client
Entrez ci-dessous le numéro de série
qui se trouve à l’arrière du boîtier du
dispositif. Conservez ces informations
pour référence ultérieure.
No. de modèle : __________________
No. de série : ____________________
Devuelva su tarjeta de registro de producto hoy
mismoy obtenga lo mejor de su compra.
Al registrar su modelo con PHILIPS usted cumplirá con los requisitos para obtener todos los valiosos
beneficios que se indican a continuación, ¡no se los pierda! Llene y devuelva su tarjeta de registro del
producto ahora mismo para garantizar:
*Comprobante
de Compra
La devolución de la tarjeta
incluida garantiza que se
archive la fecha de compra,
de modo que no necesitará
más papeleo para obtener el
servicio de garantía.
*Seguridad del
producto
Notificación
Al registrar su producto,
recibirá la notificación
(directamente del fabricante)
en el raro caso de un retiro
de productos o de defectos
en la seguridad.
*Beneficios
adicionales de la
propiedad del
producto
Registrar su producto garantiza
que recibirá todos los privile-
gios a los cuales tiene derecho,
incluyendo las ofertas espe-
ciales para ahorrar dinero.
Conozca estos símbolos de
seguridad
Este “relámpago” indica
material no aislado dentro
de la unidad que puede causar
una descarga eléctrica. Para la seguridad
de todos en su hogar, por favor no retire
la cubierta del producto.
El “signo de exclamación” llama
la atención hacia funciones
sobre las que debería leer con
atención en la literatura adjunta para
evitar problemas operativos y de
mantenimiento.
PRECAUCIÓN: Para evitar descargas
eléctricas, haga que la paleta ancha del
enchufe coincida con la ranura ancha e
introdúzcala hasta el fondo.
s t AVISO
RIESGO DE CHOQUE ELÉCTRICO NO ABRIR Atención: Para reducir el riesgo de choque elécrico, no quite la tapa (o el panel posterior). En su interior no hay piezas que el usuario pueda reparar. Para servicio dirijase a personel calificado.
Sólo para uso del cliente
Escriba a continuación el Nº de serie,
el cual se ubica en la parte posterior
del gabinete. Guarde esta información
para futura referencia.
Nº de modelo. __________________
Nº de serie. ____________________
ADVERTENCIA Para reducir el riesgo
de incendios o de descarga eléctrica, este
aparato no se debe exponer a la lluvia ni
a la humedad, y no se le deben colocar
encima objetos llenos de líquido como
jarrones.
Return your Product Registration Card today
to get the very most from your purchase.
Registering your model with PHILIPS makes you eligible for all of the valuable benefits listed below, so
don't miss out. Complete and return your Product Registration Card at once to ensure:
*Proof of
Purchase
Returning the enclosed card
guarantees that your date of
purchase will be on file, so no
additional paperwork will be
required from you to obtain
warranty service.
*Product Safety
Notification
By registering your product, you'll
receive notification - directly from
the manufacturer - in the rare
case of a product recall or safety
defect.
*Additional
Benefits of
Product
Ownership
Registering your product
guarantees that you'll receive
all of the privileges to which
you're entitled, including special
money-saving offers.
Know these
safety symbols
This “bolt of lightning” indicates
uninsulated material within your
unit may cause an electrical
shock. For the safety of everyone in your
household, please do not remove
product covering.
The “exclamation point” calls
attention to features for which
you should read the enclosed
literature closely to prevent operating
and maintenance problems.
C A U T I O N
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
For Customer Use
Enter below the Serial No. which is
located on the rear of the cabinet.
Retain this information for future
reference.
Model No. ______________________
Serial No. ______________________
WARNING: To reduce the risk of fire
or electric shock, this apparatus should
not be exposed to rain or moisture, and
objects filled with liquids, such as vases,
should not be placed on this apparatus.
ATTENTION: Pour éviter les choc
électriques, introduire la lame la plus
large de la fiche dans la borne
correspondante de la prise et pousser
jusqu’au fond.
CAUTION: To prevent electric shock,
match wide blade of plug to wide slot,
fully insert.
Class II equipment symbol
This symbol indicates that the unit has a double insulation system.
Symbole d’ un appareil de classe II
Ce symbole indique que l’appareil est équipé d’un système à double isolation.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near
water.
6. Clean only with dry cloth.
7. Do not block any ventilation
openings. Install in accordance with
the manufacturer´s instructions.
8. Do not install near any heat sources
such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the
safety purpose of the
polarized or
grounding-type plug.
A polarized plug has two blades with one
wider than the other. A grounding type plug
has two blades and a third grounding prong.
The wide blade or the third prong are
provided for your safety. If the provided plug
does not fit into your outlet, consult an
electrician for replacement of the obsolete
outlet.
10. Protect the power cord from being
walked on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the cart, stand,
tripod, bracket, or table specified
by the manufacturer or sold with
the apparatus. When a cart is
used, use caution when moving
the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
15. Battery usage CAUTION – To
prevent battery leakage which may result in
bodily injury, property damage, or damage
to the unit:
● Install all batteries correctly, + and - as
marked on the unit.
● Do not mix batteries (old and new or
carbon and alkaline, etc.).
● Remove batteries when the unit is not used
for a long time.
IMPORTANT SAFETY INSTRUCTIONS
AC Polarized Plug
16. Apparatus shall not be exposed to
dripping or splashing.
17. Do not place any sources of danger
on the apparatus (e.g. liquid filled
objects, lighted candles).
18. This product may contain lead and mercury.
Disposal of these materials may be regulated
due to environmental considerations.
For disposal or recycling information,
please contact your local authorities
or the Electronic Industries Alliance :
www.eiae.org.
EL 6475-E005: 04/01
1. Lisez ces instructions.
2. Conservez ces instructions.
3. Respectez les avertissements.
4. Suivez toutes les instructions.
5. N’utilisez pas cet appareil à
proximité d’une source d’eau.
6. Nettoyez l’appareil uniquement avec
un chiffon sec.
7. N’obstruez aucun orifice de
ventilation. Installez l’appareil selon
les instructions du fabricant.
8. N’installez pas l’appareil près d’une
source de chaleur comme par exemple
des radiateurs, bouches de chaleur,
cuisinières, ou autres appareils (même des
amplificateurs) dégageant de la chaleur.
9. Ne détruisez pas la
incorporée dans la prise
de terre ou prise
polarisée fournie. Une prise polarisée est
dotée de deux lames dont une plus large
que l’autre. Une prise de terre est dotée de
deux fiches semblables et d’une troisième,
plus large, qui assure la mise à la terre pour
votre sécurité. Si la prise fournie ne
convient pas à la prise murale dont vous
disposez, consultez un électricien pour
remplacer et adapter votre prise murale.
10. Protégez le cordon d’alimentation
pour éviter de marcher dessus ou de le
pincer particulièrement aux endroits des
prises, mâles et femelles, et au point de
raccordement sur l’appareil lui-même.
11. Utilisez uniquement des accessoires
ou options recommandés par le fabricant.
12. Utilisez uniquement un
meuble sur roulettes, un
support, un pied, une étagère ou
une table de type recommandé par le
fabr icant. Si vous utilisez un meuble sur
veillez à le
l’équipement se renversait.
13. Débranchez l’appareil pendant les
orages ou s’il doit rester inutilisé pendant
une période de temps prolongée.
14. Pour toute réparation, faites appel à un
personnel qualifié. Une réparation sera
nécessaire si l’appareil a subi des dommages
tels que détérioration du cordon
d’alimentation ou de la prise, liquide
renversé sur l’appareil, ou encore si un
est tombé dessus, si l’appareil a йtй
а la pluie ou à l’humidité, s’il ne
pas cor rectement ou s’il a fait une chute.
15. PRÉCAUTION d’emploi des
piles – Afin d’éviter toute fuite des piles
qui risquerait de causer des blessures
corporelles, des dommages matériels, ou
d’endommager l’appareil :
● Installez toutes les piles correctement,
+ et - tels qu’indiqués sur l’appareil.
● Ne mélangez pas les piles (pas de piles
neuves avec des usagées ou de piles au
carbone avec des alcalines, etc.).
● Enlevez les piles lorsque l’appareil reste
inutilisé pendant une longue période.
CONSIGNES DE SÉCURITÉ IMPORTANTES
Prise polarisée C.A.
N’exposez pas cet appareil à sources
de problème potentielles (objets
remplis de liquide, bougies allumées, etc.).
16. Cet appareil ne doit pas être exposé
à des éclaboussures.
17.
Ce produit peut contenir du plomb et du
mercure. L’élimination de ces matières est
réglementée pour protéger l’environnement.
Pour savoir comment les éliminer ou
les recycler, contactez les autorités
locales [ou Electronic Industries
Alliance : www. eiae.org]. 18.
EL 6475-F005: 04/01
roulettes, déplacer avec précaution
afin d’éviter tout accident corporel si
objet
exposé
fonctionne
1. Lea estas instrucciones.
2. Conserve estas instrucciones.
3. Lea todos los avisos.
4. Siga todas las instrucciones.
5. No utilice este aparato cerca del agua.
6. Para limpiar el aparato utilice sólo
un trapo seco.
7. No tape las aperturas de ventilación.
Proceda a su instalación de acuerdo
con las instrucciones del fabricante.
8. No instale el equipo cerca de fuentes
de calor – Como radiadores, calentadores,
estufas o cualquier otro aparato (incluyendo
los amplificadores) generador de calor.
9. No anule la
seguridad de la
clavija de corriente
(ya sea de tipo polarizado o
con toma de tierra). Las clavijas polarizadas
tienen dos patillas, una más ancha que la
otra. Las que disponen de toma de tierra
tienen dos patillas y una tercera que es la
de conexión a tierra.Tanto la patilla más
ancha como la toma de tierra han sido
incorporadas a la clavija para su seguridad
personal. Si la clavija suministrada con el
equipo no es compatible con su toma de
corriente, consulte a un electricista para
sustituir la toma de corriente obsoleta.
10.Proteja debidamente el cable
impidiendo que pueda pisarse o incluso
perforarse, especialmente en la parte más
próxima a la clavija y en el punto de salida
del equipo.
11.Utilice exclusivamente aquellos
dispositivos/ accesorios recomendados
por el fabricante.
12. Coloque el equipo
exclusivamente sobre aquellos
carros, bases, trípodes, soportes o
mesas especificados por el
vendidos con el equipo. Cuando utilice un carro,
tenga cuidado al desplazar el conjunto carro/
equipo par a evitar posibles daños por vuelco.
13. Desenchufe el aparato durante tormentas
eléctr icas o cuando no vaya a ser utilizado
lar go tiempo.
14. Confíe el mantenimiento y las
reparaciones a personal técnico especializado.
El equipo deberá repararse siempre que haya
resultado dañado dede alguna manera, como
por ejemplo por daños en el cable o en la
clavija, por derrame de líquido sobre el equipo,
por objetos que hubieran podido introducirse
en su interior, por exposición del equipo a la
lluvia o a ambientes húmedos, cuando el equipo
no funcione con normalidad o cuando hubiera
sufrido algún tipo de caída.
15.Uso de las pilas – ADVERTENCIA:
Para prevenir escapes en las pilas, que pueden
ocasionar lesiones físicas, daños a su propiedad
o dañar la unidad:
● Instale todas las pilas correctamente, + y -
como está marcado en la unidad.
● No mezcle las pilas (viejas con nuevas o
de carbono y alcalinas, etc.).
● Extraiga las pilas cuando no vaya a usar la
unidad durante largo tiempo.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Clavija polarizada de CA
comerciante o
16.El aparato no debe exponerse a goteos
ni salpicaduras.
17.No coloque nada que pueda ser
peligroso sobre el aparato (por ejemplo,
objetos llenos de líquido, velas encendidas).
18.Ese producto puede contener el plomo y
mercurio. La eliminación de este material puede
estar regulada debido a consideraciones
medioambientales. Para obtener información
sobre la eliminación o reciclaje de
material, póngase en contacto con las
autoridades locales [o con la Electronic
Industries Alliance : www. eiae.org].
EL 6475-S005: 04/01
durante
Símbolo del equipo Clase II
Este símbolo indica que la unidad tiene un sistema doble de aislamiento.
Philips, P.O. Box 520890, Miami, FL 33152 (402) 536-4171
One (1) Year Free Product Exchange
PHILIPS LIMITED WARRANTY
PHILIPS CONSUMER ELECTRONICS warrants this
product against defect in material or workmanship, subject to
any conditions set forth as follows:
PROOF OF PURCHASE:
You must have proof of the date of purchase to exchange the
product. A sales receipt or other document showing the prod-
uct, the date that you purchased the product, as well as the
authorized retailer included, is considered such proof.
COVERAGE:
Warranty coverage begins the day you buy your product. For a
period of one (1) year from the date of purchase, if the product
is determined to be defective, Philips will exchange the defec-
tive product with a new or renewed product, at its option, at
no charge. The replacement product is covered only for the
warranty period of the original product. When the warranty on
the original product expires, the warranty on all replaced prod-
ucts also expires. When it is necessary for you to ship the
product to Philips for exchange, you will pay the shipping cost
for shipment to Philips. Philips will pay the shipping costs when
returning a product to you.
Note: The exchange model supplied will be the most compara-
ble one in Philips current inventory. Shipping of your product to
Philips implies intent to follow the specified requirements of the
warranty and exchange program. Product received by Philips
cannot be returned. Replacement product can only be sent if all
warranty requirements are met. Failure to follow all require-
ments can result in delay of exchange process.
EXCLUDED FROM WARRANTY COVERAGE
Your warranty does not cover:
• Shipping charges to return defective product.
• Labor charges for installation or setup of the product, adjust-
ment of customer controls on the product, and installation
or repair of antenna systems outside of the product.
• Product repair and/or part replacement because of improper installation, connections to improper voltage supply, abuse,
neglect, misuse, accident, unauthorized repair or other cause
not within the control of Philips.
• Damage occurring to product during shipping when improp- erly packaged or cost associated with packaging.
• A product that requires modification or adaptation to enable
it to operate in any country other than the country for
which it was designed, manufactured, approved and/or
authorized, or repair of products damaged by these modifica-
tions.
• A product used for commercial or institutional purposes (including but not limited to rental purposes).
• Products lost in shipment and no signature verification of
receipt can be provided. • Products sold AS IS or RENEWED.
WHERE WARRANTY EXCHANGE IS AVAILABLE:
Exchange is available in all countries where Philips officially dis-
tributes the product. In countries where Philips does not dis-
tribute the product, the local Philips organization will attempt
to exchange the product, although there may be a delay if the
appropriate product is not readily available, or special customs
processes are implied.
FOR EXCHANGE IN THE U.S.A., PUERTO RICO, OR
U.S. VIRGIN ISLANDS…
Contact Philips Customer Care Center at:
1-800-531-0039
FOR EXCHANGE IN CANADA… 1-800-661-6162 (French Speaking)
1-800-531-0039 (English or Spanish Speaking)
REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS
THE EXCLUSIVE REMEDY OF THE CONSUMER. PHILIPS
SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSE-
QUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR
IMPLIED WARRANTY ON THIS PRODUCT. EXCEPT TO
THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIM-
ITED IN DURATION TO THE DURATION OF THIS WAR-
RANTY.
Some states do not allow the exclusions or limitation of inci-
dental or consequential damages, or allow limitations on how
long an implied warranty lasts, so the above limitations or
exclusions may not apply to you. In addition, if you enter into a
service contract agreement with the PHILIPS partnership within
ninety (90) days of the date of sale, the limitation on how long
an implied warranty lasts does not apply.
EL6587E001 / 01-04
This warranty gives you specific legal rights. You may have other rights which vary from state/province to state/province.
AZ1004_17 4/26/2004 01:38 PM Page 1