Philips Tondeuse cheveux - Manuel (Page 2)

Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that Philips
offers, register your product at www.philips.com/
welcome.
Your new Philips Professional Power hair clipper
enables comfortable clipping of even the toughest
hair. To enjoy using the hair clipper, we advise you
to read the following information.
General description (Fig. 1)
A Cutting element
B Clipping attachment
C Charging light
D On/off slide
E Handle
F Socket for appliance plug
G Large comb
H Small comb
I Setting indications
J Stubble comb
K Setting selector
L Appliance plug
M Adapter
N Cleaning brush
Important
Read this user manual carefully before you use the
appliance and save it for future reference.
Danger
- Make sure the adapter does not get wet.
Warning
- Check if the voltage indicated on the adapter
and on the appliance corresponds to the
local mains voltage before you connect the
appliance.
- The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug,
as this causes a hazardous situation.
- This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
- Children should be supervised to ensure that
they do not play with the appliance.
- Remove the clipping attachment from
the handle before you clean the clipping
attachment under the tap.
Caution
- Never immerse the handle in water or any
other liquid, nor rinse it under the tap.
- Do not use the appliance in the bath or in the
shower.
- The clipping attachment of the appliance
complies with the internationally approved IEC
safety regulations and can be safely cleaned
under a tap (Fig. 2).
- Use, charge and store the appliance at a
temperature between 15°C and 35°C.
- Only use the adapter supplied to charge the
appliance.
- If the adapter is damaged, always have it
replaced with one of the original type in order
to avoid a hazard.
- Do not use the appliance when the clipping
attachment or one of the combs is damaged or
broken as this may cause injury.
- This appliance is only intended for clipping
human scalp hair. Do not use it for any other
purpose.
Compliance with standards
This Philips appliance complies with all standards
regarding electromagnetic fields (EMF). If handled
properly and according to the instructions in this
user manual, the appliance is safe to use based on
scientific evidence available today.
Preparing for use
Charging
Charge the appliance for at least 10 hours before
you use it for the first time and after a long period
of disuse.
When the appliance is fully charged, it has a
cordless operating time of up to 35 minutes.
Do not charge the appliance for more than 24
hours.
1 Make sure the appliance is switched off.
2 Insert the small plug into the socket of the
appliance and put the adapter in the wall
socket (Fig. 3).
3 After a few seconds, the charging light
goes on to indicate that the appliance is
charging (Fig. 4).
Note: The charging light does not change colour and
does not go out when the appliance is fully charged.
Optimising the lifetime of the
rechargeable batteries
To optimise the lifetime of the batteries, follow the
instructions below:
- After the appliance has been charged for the
first time, do not recharge it between clipping
sessions. Continue using it and recharge it only
when the batteries are almost empty.
- Remove the adapter from the wall socket
when the batteries are fully charged (which
takes 10 hours).
- Discharge the batteries completely twice a year
by letting the motor run until it stops. Then fully
recharge the batteries.
Corded clipping
Note: Only run the appliance from the mains when
the rechargeable batteries are empty.
Note: If the batteries are completely empty, wait a
few minutes before you switch on the appliance.
1 Switch off the appliance.
2 Insert the small plug into the appliance and
put the adapter in the wall socket (Fig. 3).
3 After a few seconds, switch on the appliance.
Using the appliance
Preparing for hair clipping
Only use the appliance on clean, dry hair. Do not
use it on freshly washed hair.
1 Make sure that the head of the person whose
hair you intend to cut is at the same level as
your chest. This ensures that all parts of the
head are clearly visible and within easy reach.
2 Comb the hair in the growth direction (Fig. 5).
Clipping with comb
The appliance comes with three combs for 15
different hair lengths.
The minimum remaining hair length is 1.6mm and
the maximum remaining hair length is 41mm.
1 Select the comb you want to use.
The table shows how long the hair will be after
clipping at the different settings of the small comb
and large comb.
Settings of the small and large comb
Setting Hair length after
clipping with
small comb
Hair length after
clipping with
large comb
1 3mm 23mm
2 6mm 26mm
3 9mm 29mm
4 12mm 32mm
5 15mm 35mm
6 18mm 38mm
7 21mm 41mm
Tip: Write down the settings you have used to create
a certain hairstyle as a reminder for future clipping
sessions.
Stubble comb for a ‘stubble look’
- To create a ‘stubble look’, clip with the small
comb set to setting 1 (3mm) first.
- Then clip the hair with the stubble comb for a
hair length of 1.6mm.
2 Slide the selected comb into the guiding
grooves on both sides of the handle
(‘click’) (Fig. 6).
3 To set the comb to the desired setting, press
the setting selector (1) and slide the comb to
the desired hair length setting (2) (Fig. 7).
, The setting indications on the comb show the
selected setting.
4 Switch on the appliance.
5 Move the appliance through the hair slowly.
- To clip in the most effective way, move the
appliance against the direction of hair growth.
- Since all hair does not grow in the same
direction, you need to move the appliance in
different directions (upward, downward or
across) (Fig. 8).
- Make sure that the flat part of the comb is
always fully in contact with the scalp to obtain
an even result.
- Make overlapping passes over the head to
ensure that you cut all the hair that needs to
be cut.
- To achieve a good result with curly, sparse or
long hair, use a hand comb to guide the hair
towards the appliance.
6 Regularly remove cut hair from the comb.
If a lot of hair has accumulated in the comb,
remove the comb from the appliance and blow
and/or shake the hair out of it.
Contouring without comb
You can use the appliance without comb to clip
hair very close to the skin (0.6mm) or to contour
the neckline and the area around the ears.
Be careful when you clip without comb because
the cutting element removes every hair it
touches.
1 Pull the comb off the appliance (Fig. 9).
2 Before you start to contour the hairline
around the ears, comb the hair ends over the
ears.
3 Tilt the appliance in such a way that only one
edge of the cutting element touches the hair
ends when you shape the contours around
the ears (Fig. 10).
Only cut the hair ends. The hairline should be close
to the ear.
ENGLISH
2 4222.002.8139.1