SawStop Bases Mobiles - Manuel (Page 61)

SawStop Assemblage de Guide Supérieur
|
59
Le déballage de votre assemblage de guide
Lors du déballage de votre assemblage de guide, vérifiez que toutes les composantes se trouvant sur cette
page sont incluses. Portez une attention particulière lorsque vous déballez votre assemblage de guide afin de
prévenir tout dommage aux composantes.
main tube
front rail
rear rail
extension table
installation instructions poster owner’s manual
fence handle
fence assembly
hardware pack
premium rip fence
10 90
10 20 30 40 50
0
60 70 80
90
10 20 30 40 50 60 70 80 20
90
10 20 30 40 50 60 70 80 30
90
10 20 30 40 50 60 70 80 400
90
10 20 30 40 50 60 70 80 500
90
10 20 30 40 50 60 70 80 600
90
10 20 30 40 50 60 70 80 700 10 20 30 40 50 60
0 10 20 30 40 50 60 70 80 90 100 10 20 30 40 50 60 70 80 90 200 10 20 30 40 50 60 70 80 90 300
SawStop
SawStop
®
OWNER’S MANUAL
Premium Fence Assembly
Fence Assembly Hardware Pack
2 Flat Head Socket Bolts, M8x1.25x25 (8)
Flat Head Socket Bolts, M8x1.25x16 (8) 1
Washers, M8x23x2 (15 + 1 extra) 3
Lock Washers, M8 (15 + 1 extra) 4
Hex Nuts, M8x1.25 (8) 5
6 Hex Head Bolts, M8x1.0x16 (7)
Installing Your SawStop Premium Fence Assembly SawStop Service Department 503-582-9934 www.sawstop.com
© SawStop, LLC
4
9
3 2 1
8 5 6 7
Before assembling your Premium Fence Assembly, make sure that you have all the necessary components identified on page 1 in the owner’s manual, including the fence assembly hardware pack. Call the SawStop Service Department at 503-582-9934 if any components are missing. You will also need the following tools to complete the fence assembly installation:
1. a 3 mm hex key 2. a 5 mm hex key 3. a 13 mm wrench 4. a straight-edge
• Locate the front rail, the rear rail, and the fence assembly hardware pack. All of the hardware needed to install the fence system is located on the fence assembly hardware pack. In order to easily identify the hardware used in each of the following steps, the different pieces of hardware are numbered on the hardware pack and in the figures.
Note: Your saw must be fully assembled before installing the fence system.
• Take the front rail (the larger of the two rails) and align it to the front edge of your saw by centering the notches in the rail with the two miter slots in the table and aligning the two holes between the notches with the two corresponding holes in the front edge of the table. Aligning the two holes between the notches aligns all the other holes used in mounting the front rail to your saw; different holes are used for different saws. When the holes are aligned, mount the front rail to the saw by taking four M8x1.25x16 flat head socket bolts and threading one into each of the four threaded holes in the front edge of the main table. Tighten the four bolts using a 5 mm hex key.
1
miter slots
1
front rail
notches
• Take two M8x1.25x25 flat head socket bolts and insert one through the open hole at the end of each extension wing. 2
2 2
• Place an M8x23x2 washer and an M8 lock washer on the back of each of the M8x1.25x25 flat head socket bolts that extend through the extension wings, and then thread an M8x1.25 hex nut on each bolt. Hand tighten the nuts; do not fully tighten them.
3 4 2
5
SawStop System Status Codes Status Red Grn
Wet Wood Overload D ue To During Bypa ss Contact Dete cted During Stan dby Contact Dete cted Brake Adjust Positi on of Doors Close Acces s Key To “On” Turn Cartrid ge To “Off” Turn Start S witch Bypass Mod e On Coasting Do wn Replace Ca rtridge System Rea dy System Initia lizing
• • • • • •
• • • • • •
• • • • • •
• • • • • • • • • • • •
• • • • • •
• • • • • •
2
3 4 5
• Use a straight-edge to level the front edge of the left extension wing to the cast iron table top. You may have to pull up or push down on the outer edge of the extension wing to level it. Once the front edge of the left extension wing is level, use a 5 mm hex key and a 13 mm wrench to fully tighten the nut on the bolt that mounts the left extension wing to the front rail. Repeat this process to level the front edge of the right extension wing. straight-edge
level the extension wing and tighten the nut on this bolt
• Take the rear rail (the smaller of the two rails) and align it to the rear edge of your saw by centering the notches in the rail with the two miter slots in the table and aligning the left-most hole between the notches with the corresponding hole in the rear edge of the table. There are three holes in the rail between the notches, one solitary hole and two holes paired together, and the left-most hole is the solitary hole. Not all of the holes are used to mount the rail to your saw; different holes are used for different saws. Aligning the left-most hole aligns all the other holes used in mounting the rear rail to your saw. When the holes are aligned, mount the rear rail to the saw by taking four M8x1.25x16 flat head socket bolts and threading one into each of the four threaded holes in the rear edge of the main table. Tighten the four bolts using a 5 mm hex key.
! WARNING Moving gears and parts can pinc h, cut o r crush. Do no t oper ate w ith door o pen. align the left-most hole between the notches
1
1
! WA RN ING Mo ving ge ar s a nd pa rts ca n p inc h, cu t o r c ru sh. Do no t o pe ra te w ith do or op en.
• Take two M8x1.25x25 flat head socket bolts and insert one through the open hole at the end of each extension wing. Place an M8x23x2 washer and an M8 lock washer on the back of each of bolt and then thread an M8x1.25 hex nut on each bolt. Hand tighten the nuts; do not fully tighten them.
2
3 4 5
2 5 4 3
2
2
• Use a straight-edge to level the rear edge of the left extension wing to the cast iron table top. You may have to pull up or push down on the outer edge of the extension wing to level it. Once the rear edge of the left extension wing is level,
use a 5 mm hex key and a 13 mm wrench to fully
straight-edge
level the extension wing and tighten the nut on this bolt
Fence Assembly Hardware Pack
2 Flat Head Socket Bolts, M8x1.25x25 (8)
Flat Head Socket Bolts, M8x1.25x16 (8) 1
Washers, M8x23x2 (15 + 1 extra) 3
Lock Washers, M8 (15 + 1 extra) 4
Hex Nuts, M8x1.25 (8) 5
6 Hex Head Bolts, M8x1.0x16 (7)
• The next step of the assembly is easiest with two people. Position the extension table between the front and rear rails. Make sure that the table is oriented so that the adjustment bracket is closest to the right extension wing. Tilt the extension table slightly so that the adjustment bracket can fit under the edge of the extension wing. Position the extension table so that the end of the adjustment bolt aligns with the corresponding threaded hole in the bottom of the extension wing. With the weight of the extension table still supported, turn the adjustment bolt until the extension table is roughly flush with the extension wing.
adjustment bolt
adjustment bracket
adjustment bracket
rail avant
rail arrière
tube principal
table de rallonge
poignée de guide
guide de refente
supérieur
affiche pour instructions
d’installation
guide de
l’utilisateur
emballage de
quincaillerie pour
assemblage de guide