Sunlite SR50M1X6-PD - Manuel

Important Safety InStructIonS - Save theSe InStructIonS
uSe only wIth claSS 2 power unIt
• These products are only suitable for connection to a Class 2 power
source and have not been evaluated for use when connected to a
power source that does not comply with Class 2 voltage and energy
limited supplies.
all InStallatIonS of SunStar50 Should be
performed by a certIfIed electrIcIan and be In
complIance wIth the natIonal electrIcIanS code aS
well aS local codeS.
SuItable for damp locatIonS
M odel M ax I nput V oltage (V dc ) M ax c urrent ( M a) M ax W attage
SR50-PD 24 700 7.8
F
Ixture
W
IrIng
:
1 2
4
Thread fixture wire
through ceiling mount.
Outfit fixture wire with
bullet connections.
• Core (+) with a male
bullet connector.
• Shield (-) with a fe-
male bullet connector.
3
5 6
Connect fixture. Push wires into ceiling.
for tradItIonal
mount baSe:
Screw in #8 screws into
mount base to connect
the base to bracket.
for receSSed
mount baSe:
Hold fins flush to ceiling
mount body and insert
into the ceiling.
Cut or drill a 1-1/8” hole
in ceiling.
Retrieve wires in ceiling
and outfit with bullet
connections.
• Side of the wire closer
to LED driver should
be fitted with a female
bullet connector.
• Side of the wire farther
from the LED driver
should be fitted with a
male bullet connector.
tradItIonal mount
baSe only.
Screw in mounting
bracket over hole.
If using Recessed Mount
Base, skip this step and
proceed to step 4.
conSIGneS de SÉcurItÉ ImportanteS - conServeZ SoIGneuSement ceS InStructIonS
a utIlISer unIQuement avec une Source d’alImentatIon
de claSSe 2
• Ces produits doivent être branchés uniquement à une source
d’alimentation de classe 2 et n’ont pas été testés pour une utilisation
lors d’une connexion à une source d’énergie non conforme à la tension
de classe 2 et à l’approvisionnement en énergie limitées.
ce produIt doIt Étre InStallÉ Selon le code
d’InStallatIon pertInent, par une perSonne QuI connaÍt
bIen le produIt et Son fonctIonnement aInSI Que leS
rISQueS InhÉrentS.
convIent auX emplacementS humIdeS.
SunStar50 - “Sr50-pd-” - Low VoLtage Surface Mounted LuMinaire
E338721
SoLid State Led
SR50-PD
interior pendant
C
ERtifiCation
:
UL and cUL
Danp Location Listed
IP64 Rated
E
nERgy
:
>0.9 Power Factor
700mA / 10VDC
-30° C to 40°C
C
ontaCt
:
4811 Quail Crest Place
Lawrence, KS 66049
www.sunlitest.com
T:785.856.0219
f
ixtuRE
i
nStallation
i
nStRuCtionS
:
Suggested wiring utilizes bullet connections in alignment with the direction of current flow from the driver.
R(+) R(+) R(+) R(+) B(-) B(-) B(-)
SR50 SR50 SR50 SR50
B(-)
T o P ower S uPPly
T o S erieS
F ixTure
r(+) r(+)
r(+) B(-)
T o P ower S uPPly