STI SS-2407EX - Manuel

INSTALLATION OF SS-2007 SERIES STOPPER ® STATION
All specifications and information shown were current as of publication, and are subject to change without notice.
10278IS APRIL2011
NO - NORMALLY OPEN
NC - NORMALLY CLOSED
C - COMMON
10A, 1/2 HP, 125/250 VAC
6A, 30 VDC
MODELS WITH LT-1 TIMER:
FORM C CONTACTS RATED
120 VAC, 3A
28 VDC, 3A TYPE BASE VOLTS WATTS AMPS
RADION PT. NO.
OR EQUIVALENT AVERAGE
LIFE (Hrs.)
FILAMENT
T3-1/4
WEDGE
6.3 1.57 0.25 3000
FILAMENT T3-1/4
WEDGE 14 1.12 0.08 15,000
FILAMENT
T3-1/4
WEDGE
28 1.68 0.06 2500
50N8079 / #555
#658
50N8109 / #656
TERMINAL BLOCK LEGEND SWITCH RATINGS CHART LAMP CHART
Safety Technology International, Inc.
2306 Airport Road • Waterford, Michigan 48327-1209
Phone: 248-673-9898 • Fax: 248-673-1246
Toll Free: 800-888-4784 • E-mail: [email protected]
Web: www.sti-usa.com
Safety Technology International (Europe) Ltd.
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England • Tel: 44 (0) 1527 520 999
Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only)
E-mail: [email protected] • Web: www.sti-europe.com
VIEW SHOWING INSTALLATION OF LAMP
HOLDER TO BUTTON ASSEMBLY
MULTIPLE DEVICES N/C LIGHT MAINTAINED SERIES WIRING
SINGLE DEVICE LIGHT
MAINTAINED FOR LAMP VOLTAGE
SEE CHART BELOW
MULTIPLE DEVICES
N/O LIGHT
MAINTAINED
PARALLEL WIRING
*SS-2007/LTLUL NOTES: For access control installations, power for the LT-1UL Timer must be supplied by a power source listed to UL294. When used for access
control, this device shall be used as part of an access controlled egress door system. It is up to the local AHJ to allow use of this device in place of an automatic sensor.
For higher security installations, lower time limits should be used. For SS-2007/LTUL the enclosed timer is to be used and installed per the enclosed LT-1UL installation
sheet. SS-2007/LTUL maximum rating 30 VDC 3A.
Electronic warranty form at www.sti-usa.com/wc14
INSERT BUTTON ASSEMBLY INDEXING TABS
INTO LAMP HOLDER SLOTS THEN TWIST CLOCKWISE
AS SHOWN TO LOCK.
BACKPLATE ASSEMBLY
+ # 1 # 2 _ # 3
L
TO DEVICES
L
L
O
+
O
L
O
L
+ _
L
C N/O
TO DEVICES
C N O
+ _
L
# 1
C N O
L
# 2
C N O
L
# 3
TO DEVICES
S
O
+
SWITCH ASSEMBLY
SEE VIEW BELOW
BURNDY FORK
TERMINAL #TP14-6F
OR EQUIVALENT
10112 SWITCH ASSEMBLY
WITH SCREW TERMINALS
SEE SWITCH RATINGS CHART
( )
C
NO
NC
+
( ) +
- ( )
LAMP HOLDER
(PART OF SWITCH
ASSEMBLY)
14-16 AWG
BURNDY SPADE
TERMINAL #NC14F2590
OR EQUIVALENT LAMP (SEE CHART)
STANDARD #656
10277 SHELL WHITE
10272-S BACKPLATE
ASSEMBLY
(SMOKE COLOR ONLY)
BUTTON ASSEMBLY
10111 (GREEN)
10110 (RED)
10271 STATION HOUSING
RED, GREEN, WHITE, YELLOW
AND BLUE
STATION LABEL
19001 SCREW #8-32 X 3/8 in.
(1) PROVIDED
19015 ALLEN WRENCH
3/32 (1) PROVIDED
19021 GROUND LUG
#10-32 x 3/8 in.
(1) PROVIDED
19010 SCREWS
#6-32 x 1 in.
BACKPLATE TO
ELECTRICAL BOX
(2) PROVIDED
RETAINING NUT
PU
SH
REMARQUES POUR *SS-2**7/LT1-UL: Pour les installations de contrôle d’accès, l’alimentation de la minuterie LT-1UL doit être fournie par une source homologuée UL294. Lorsque
cet appareil est utilisé aux fins de contrôle d’accès, il doit faire partie d’un système de porte de sortie à accès contrôlé. Il incombe donc à l’AHJ local d’autoriser l’utilisation de cet
appareil au lieu d’un capteur automatique. Pour les installations de sécurité plus renforcée, des délais inférieurs doivent être utilisés. Pour les modèles SS-2**7/LT1-UL, la minuterie
intégrée doit être installée et utilisée suivant la fiche d’installation LT-1UL fournie. La cote maximale des modèles * SS-2**7/LT1-UL est de 30 VCC 3A.