Unusual sounds, No heat, Dryer displaying code message – Whirlpool WGD9450WL Manuel d'utilisation

Page 12: Dryer results, Warning

Advertising
background image

12

Unusual sounds

Has the dryer had a period of non-use?

If the dryer hasn’t been used for a while, there may be a
thumping sound during the first few minutes of operation.

Is a coin, button, or paper clip caught between the drum
and front or rear of the dryer?

Check the front and rear edges of the drum for small objects.
Clean out pockets before laundering.

Are the four legs installed, and is the dryer level front to
back and side to side?

The dryer may vibrate if not properly installed. See the
Installation Instructions.

Is the clothing knotted or balled up?

When balled up, the load will bounce, causing the dryer to
vibrate. Separate the load items and restart the dryer.

No heat

Has a household fuse blown, or has a circuit breaker
tripped?

The drum may be turning, but you may not have heat. Electric
dryers use 2 household fuses or circuit breakers. Replace the
fuse or reset the circuit breaker. If the problem continues, call
an electrician.

Dryer displaying code message

“PF” (power failure), check the following:

Was the drying cycle interrupted by a power failure?

Press and hold START to restart the dryer.

“L2” Diagnostic Code (low or no line voltage condition):

The drum will turn, but there may be a problem with your
home power supply keeping the dryer's heater from turning
on. The dryer will continue to run when this diagnostic code is
present. Press any key to clear the code from the display and
return to the estimated time remaining.

Try the following:

Check to see if a household fuse has blown or circuit breaker
has tripped. Electric dryers use two household fuses or
breakers. Replace the fuse or reset the circuit breaker.

Confirm the power cord is properly installed. Refer to
“Electrical Connection” for details.

Select a Timed Dry heated cycle, and restart the dryer.

If the message persists, consult a qualified electrician.

“AF” (low airflow condition):

The dryer will continue to run when this diagnostic code is
present. Press any key to clear the code from the display and
return to the estimated time remaining.

Try the following:

Clean lint screen.

Check to see if the vent run from the dryer to the wall is
crushed or kinked.

Confirm the vent run from the dryer to the wall is free of lint
and debris.

Confirm the exterior vent exhaust hood is free of lint and
debris.

Confirm your vent system falls within the recommended
run length and number of elbows for the type of vent you
are using. Refer to “Plan Vent System” in the Installation
Instructions for details.

Select a Timed Dry heated cycle, and restart the dryer.

If the message persists, have your entire home venting run
cleaned.

“E” Variable (E1, E2, E3) service codes: Call for service.

Dryer Results

Clothes are not drying satisfactorily, drying times are too
long, or load is too hot

Is the lint screen clogged with lint?

Lint screen should be cleaned before each load.

Has the Air Only temperature setting been selected?

Select the right temperature for the types of garments being
dried. See “Additional Features.”

Is the load too large and heavy to dry quickly?

Separate the load to tumble freely.

Are clothes coming out of the Refresh cycle with damp or
wet spots?

Under certain environmental or installation conditions you may
experience underdrying. Select the Enhanced Touch Up cycle
(20 min. default time), which can be customized by selecting
High temperature and/or additional cycle time by pressing the
Dry Time up button.

WARNING

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death
or fire.

Is the exhaust vent or outside exhaust hood clogged with
lint, restricting air movement?

Run the dryer for 5-10 minutes. Hold your hand under the
outside exhaust hood to check air movement. If you do not
feel air movement, clean exhaust system of lint or replace
exhaust vent with heavy metal or flexible metal vent. See the
Installation Instructions.

Are fabric softener sheets blocking the grille?

Use only one fabric softener sheet, and use it only once.

Is the exhaust vent the correct length?

Check that the exhaust vent is not too long or has too many
turns. Long venting will increase drying times. See the
Installation Instructions.

Advertising