Whirlpool 9760332A - Manuel (Page 14)

14
To Program Next Steps (2 through 4) of the Sequence:
1. Press FIRST/NEXT STEP.
“PROGRAM” and “STEP” will appear on the display. The
number of the step being programmed will flash. “START”
and “TIME” will also appear on the display.
2. Choose any desired cooking function.
3. Press TEMP or TEMP/HOUR “up” or “down” arrow pad (if
desired) to select a temperature other than the one displayed.
4. Press STOP TIME, then HR and MIN or TEMP/HOUR “up” or
“down” arrow pads to select a stop time. For example, 1:35.
5. Continue repeating steps 1 through 4 until the desired
number of sequences have been set. You can program up to
4 cooking functions within the sequence.
6. Press START to begin sequence.
If you choose to press START, your program sequence will
begin. Additional steps cannot be added to the sequence
once START has been pressed.
Press CANCEL at any time to clear program and to stop
program.
To Review/Modify Programmed Sequence:
If program steps are partially or completely programmed, yet the
sequence has not been started, the programmed cooking
functions can be reviewed.
1. Press REVIEW STEPS. Step 1 will appear in the display.
Subsequent presses of REVIEW STEPS will cause display of
programmed steps in order.
“STEP” and “RECALL” will appear on the display. The
number of the displayed step will flash. A recalled step will
remain lit on the display for 5 minutes if no further action is
taken.
2. If fewer than 4 steps have been programmed, press REVIEW
STEPS repeatedly until the last programmed step is
displayed, then press FIRST/NEXT STEP if it is desired to
program an additional step.
While a step is recalled, a cook function pad can be used to
change the function, or the TEMP or TEMP/HOUR “up” or
“down” arrow pad can be used to change the set
temperature.
START TIME, when used with the HR or MIN or TEMP/HOUR
“up” or “down” arrow pads, can be used to change, add or
delete a delayed start.
STOP TIME can be used to change the stop time. Changing
the stop time of a step will automatically change the start
times and stop times of all subsequent programmed cook
functions.
3. After Review/Modification of the programmed sequence is
complete, press START to begin sequence.
To Modify Sequence Programming:
1. Press UNDO.
The last step of the sequence will be canceled, and the step
prior to the canceled sequence will show on the display for
either review or modification.
If the programmed sequence has not been started, see “To
Program Next Steps of the Sequence” section to program a
step to replace the canceled cook function.
2. Press START.
The first step will show on the display and the program
sequence will begin.
Changes can be made during a programmed cook function;
however, changes cannot be made after a programmed cook
function has been completed.
If at any time during an active sequenced program
FIRST/NEXT STEP is pressed, 3 tones will sound.
RANGE CARE
Self-Cleaning Cycle (on some models)
IMPORTANT: The health of some birds is extremely sensitive to
the fumes given off during the Self-Cleaning cycle. Exposure to
the fumes may result in death to certain birds. Always move birds
to another closed and well-ventilated room.
Self-clean the oven before it becomes heavily soiled. Heavy soil
results in longer cleaning and more smoke.
Keep the kitchen well-ventilated during the Self-Cleaning cycle to
help get rid of heat, odors, and smoke.
Do not block the oven vent(s) during the Self-Cleaning cycle. Air
must be able to move freely. Depending on your model, see
“Oven Vent” or “Oven Vents” section.
Do not clean, rub, damage or move the oven door gasket. The
door gasket is essential for a good seal.
Prepare Oven:
■ Remove the broiler pan, grid, cookware and bakeware and,
on some models, the temperature probe from the oven.
■ Remove any foil from the oven because it may burn or melt,
damaging the oven.
■ Remove oven racks to keep them shiny and easy to slide.
See “General Cleaning” section for more information.
■ Hand clean inside door edge and the 1½" (3.8 cm) area
around the inside oven cavity frame, being certain not to
move or bend the gasket. This area does not get hot enough
during self-cleaning to remove soil. Do not let water, cleaner,
etc. enter slots on door frame. Use a damp cloth to clean this
area.
■ Wipe out any loose soil to reduce smoke and avoid damage.
At high temperatures, foods react with porcelain. Staining,
etching, pitting or faint white spots can result. This will not
affect cooking performance.
WARNING
Burn Hazard
Do not touch the oven during the Self-Cleaning cycle.
Keep children away from oven during
Self-Cleaning cycle.
Failure to follow these instructions can result in burns.