Toshiba 19A26C - Manuel (Page 9)

9
TO MEMORIZE CHANNELS
This TV is equipped with a channel memory feature that allows the
TV to skip up or down to the next channel in the TV’s memory,
skipping over unwanted channels.
Before selecting channels, you must program them into the TV’s
memory. In addition to normal VHF and UHF channels, this TV can
receive up to 113 Cable TV channels. To use this TV with an
antenna, set the TV/CABLE menu option to the TV setting. When
shipped from the factory, this menu option is in the CABLE setting.
TV/CABLE SELECTION
Press MENU.
Press SET + or – until the indicator next to
“CH SETUP” begins to flash, then press
ENTER.
Press SET + or – until the indicator next
to “TV/CABLE” begins to flash.
Press ENTER to select the TV or CABLE
mode. The arrow indicates the selected
mode.
Repeatedly press MENU until the
menu screen closes.
NOTE:
Contact your cable company to determine the type of cable
system used in your area.
Repeatedly press MENU until the menu screen closes.
TO ADD/DELETE CHANNELS
Press MENU.
Press SET + or – until the indicator next to
“CH SETUP” begins to flash, then press
ENTER.
Press SET + or – until the indicator
next to “ADD/DELETE” begins to
flash, then press ENTER.
Select the desired channels to be
added or deleted using the Direct
Channel Selection buttons (0–9),
CH + or –, SET + or –.
1
2
3
4
5
4
1
2
3
4
5 Press ENTER to select ADD or DELETE.
If an unmemorized channel was selected (step 4), the
channel indication will be red. Press ENTER if you wish
to ADD the unmemorized channel. The channel
indicator will change from red to green when a channel
is added and the channel will be memorized.
If a memorized channel was selected (step 4), the
channel indication will be green. To delete the channel
Repeatedly press MENU until the menu screen closes. 6
from memory, press ENTER repeatedly
until “DEL” appears on-screen. The
channel indicator will change from
green to red when a channel is deleted.
Repeat steps 4 and 5 for each channel
to be added or deleted.
ADD CH 012
〈 0 – 9 / + / – / ENTER / MENU 〉
AUTOMATIC CHANNEL MEMORY
Press MENU.
Press SET + or – until the indicator next to
“CH SETUP” begins to flash, then press
ENTER.
1
2
Press SET + or – until the indicator next
to “AUTO CH MEMORY” begins to flash,
then press ENTER. The TV will begin
memorizing all the channels available in
your area. Channel numbers will remain
red until auto memorizing is complete. 3
ADJUSTING THE PICTURE
You can adjust the settings for brightness, contrast, color,
tint and sharpness.
1
2
4 Press SET + or – to adjust the setting.
CONTRAST COLOR BRIGHTNESS TINT SHARPNESS
3
Press MENU.
Press SET + or – until the indicator next to “PICTURE”
begins to flash, then press ENTER.
Repeatedly press ENTER to select the item you want to
adjust.
TO RETURN TO FACTORY SETTINGS:
Press RESET while the picture adjusting mode is
on-screen.
BRIGHTNESS
CONTRAST
COLOR
TINT
SHARPNESS
+
higher
lighter
deeper
greenish
lower
darker
paler
reddish
softer sharper
–
AUTO CH MEMORY
TV
ADD / DELETE
CABLE
〈 + / – / ENTER / MENU 〉
AUTO CH MEMORY
TV
ADD / DELETE
CABLE
〈 + / – / ENTER / MENU 〉
AUTO CH MEMORY
TV
ADD / DELETE
CABLE
〈 + / – / ENTER / MENU 〉
MENU
〈 + / Ð / ENTER / MENU〉
PICTURE
LANGUAGE
LOCK
CH SETUP
ON TIMER
MENU
〈 + / Ð / ENTER / MENU〉
PICTURE
LANGUAGE
LOCK
CH SETUP
ON TIMER
MENU
〈 + / Ð / ENTER / MENU〉
PICTURE
LANGUAGE
LOCK
CH SETUP
ON TIMER
3X00221A(E)_P08-12 22/12/05, 4:41 PM 9