Programming without a code – Panasonic CT 32SL15 Manuel d'utilisation
Page 42
R
EMOTE
C
ONTROL
O
PERATION
/ O
PERACIÓN
DEL
C
ONTROL
R
EMOTO
/ F
ONCTIONNEMENT
DE
LA
TÉLÉCOMMANDE
Re
mot
e
Re
m
o
to
Télécomma
nde
Programming The Remote Control
Programación del Control Remoto
Programmation de la télécommande
The Universal Remote Control can be programmed to
operate many manufacturers’ components, using the
component function buttons for VCR, DVD, CABLE or
DBS. Follow the procedures for programming your Remote
Control with or without a code for the component.
El Control Remoto Universal puede programarse para
operar componentes de varios fabricantes usando los
botones de función para VCR, DVD, CABLE o DBS.
Siga los procedimientos para programar su Control
Remoto con o sin código para el componente.
La télécommande universelle peut être programmée pour
commander le fonctionnement d'appareils d'autres
marques à l'aide des touches de fonctions VCR, DVD,
CABLE, ou DBS. Suivre l'une des procédures de
programmation données ci-dessous.
Note:
Determine the manufacturer of the component and look in the
table for the code.
Nota:
Determine el fabricante del componente y busque en la
tabla su código.
Nota:
Noter la marque de l'appareil et identifier le code dans le
tableau des codes.
English Procedures
1. Confirm that the external component is plugged in and
operating.
2. Turn the component off.
3. Press
and
together,
for at least 5
seconds. After 5 seconds, the illuminated mode
(component) buttons will begin to flash. Release the
ACTION and POWER buttons.
4. Press appropriate component button on the Remote
Control VCR, DVD, CABLE or DBS. The component
button will illuminate steadily and all others will go out.
5. Enter the 3-digit component code using the Remote
Control numeric keypad (0 ~ 9 buttons). The component
button will blink twice.
6. Press the Remote Control
to test the
component. If the procedure was successful, the
component will turn on and the component key will blink
twice and then go out.
Note:
If the component does not operate with the Remote Control,
repeat steps 3 through 6 using another code (some brands
have multiple codes). If an incorrect code is entered, or if the
procedure takes longer than 30 seconds, the programming will
fail.
Programming Without A Code
This procedure searches all codes and is called the
“sequence method.”
1. Confirm that the external component is plugged in and
on.
2. Turn the component off.
3. Press
and
together,
for at least 5
seconds. After 5 seconds, the illuminated mode
(component) buttons will begin to flash. Release the
ACTION and POWER buttons.
4. Press the appropriate component button on the Remote
Control. The component button will illuminate steadily
and all others will go out.
5. Press the
button to set the remote control into
the step and set mode.
6. Point the remote control towards the component.
7. Press VOL X (the mode key will blink three times), then
press the Remote Control
button to test the
component. Continue this process until the proper code
is found. If the procedure was successful, the component
will turn on.
Note:
Each time you press the VOL X button, make sure that the
component key blinks twice before pressing the POWER
button.
8. Once the device responds, press
to store the
code. The mode (component) button will blink twice.
Note:
It may take many attempts before the correct code is found. If
you miss a code, press W VOL, then press the
button to test the component.
Procedimiento Español
1. Confirme que el componente esté conectado y en
operación.
2. Apague el componente.
3. Presione los botones de
y
juntos,
cuando menos 5 segundos. Después de este tiempo,
los botones de componentes comenzarán a destellar.
Desoprima los botones ACTION y POWER.
4. Presione el botón de la función apropiada del
componente en el Control Remoto. (VCR, DVD, CABLE
o DBS). El botón seleccionado quedará iluminado y el
resto se apagará.
5. Accese el código del componente de 3 dígitos usando el
teclado numérico (botones 0 ~ 9) del Control Remoto. El
botón del componente destellará dos veces.
6. Presione el botón
de el Control Remoto para
probar el componente. Si éste procedimiento ha sido
exitoso, el componente se encenderá.
Device
Equipo
Appareil
Operates
Funciona
Contrôle
Default
Réglage par défaut
TV
Televisión
Téléviseur
Panasonic Only
Solo Panasonic
Panasonic seulement
Panasonic Code
Código TV Panasonic
Codes Panasonic
VCR
Videocasetera
Magnétoscope
VCR (Preset)
Videocasetera
(predefinido)
Magnétoscope (
Préréglé
)
Panasonic Code
Código Panasonic
Codes Panasonic
DBS/CBL
DBS STB & CBL STB
(Preset/predefinido/ Préréglé)
Panasonic DBS Code
Código Panasonic DBS
Codes DBS Panasonic
DVD
Lecteur DVD
DVD (Preset)
DVD/disco Compacto
(predefinido)
Lecteur DVD et CD (Préréglé)
Panasonic Code
Código Panasonic
Codes Panasonic
ACTION
POWER
POWER
ACTION
POWER
POWER
POWER
ACTION
POWER
ACTION
POWER
POWER