Making basic connections to the tv, Mounting the swivel and tv to the stand, Cable tv – Philips Cineos 44PL9523 Manuel d'utilisation
Page 3
3
Making Basic Connections to the TV
Cable TV
DVI
G S-VIDEO
G S-VIDEO
R
L
V
R
L
R
L
R
L
V
Pr
Pb
Y
R
L
R
L
Pr
Pb
Y
Pr
Pb
Y
R
L
V
STANDARD/
HD INPUTS
STANDARD/
HD INPUTS
TUNER
RGB+HV
AV
5
A
V
6
AV
1
MON
SUB OUT
A
V
2
AV
3
AV
4
OUT
SER
VICE 1
2
C
DVI
G
S-VIDEO
G
S-VIDEO
R
L
V
R
L
R
L
R
L
V
Pr
Pb
Y
R
L
R
L
Pr
Pb
Y
Pr
Pb
Y
R
L
V
STANDARD/
HD INPUTS
STANDARD/
HD INPUTS
TUNER
RGB+HV
AV
5
A
V
6
AV
1
MON
SUB OUT
A
V
2
AV
3
AV
4
OUT
SER
VICE 1
2
C
Back of TV
Incoming
Cable TV
Signal
Connect the incoming cable
TV signal to the TUNER
jack on the back of the TV.
Mounting the Swivel and TV to the Stand
1
POWER
SELECT
GUIDE
INFO
HIGH DEFINITION
POWER
OPEN/CLOSE
STANDBY-ON
STOP
PREV
NEXT
PLAY
PAUSE
DVD619 DVD/CD PLAYER
DVI
G S-VIDEO
G S-VIDEO
R
L
V
R
L
R
L
R
L
V
Pr
Pb
Y
R
L
R
L
Pr
Pb
Y
Pr
Pb
Y
R
L
V
STANDARD/
HD INPUTS
STANDARD/
HD INPUTS
TUNER
RGB+HV
AV
5
A
V
6
AV
1
MON
SUB OUT
A
V2
AV
3
AV
4
OUT
SER
V
ICE 1
2
C
C
E
N
T
E
R
C
H
A
N
N
E
L
A
M
P
IN
P
U
T
INT
EXT
Screws
Dowels
2
3
4
5
1
Install the positioning dowels in the stand.
2
Place the TV and mounted swivel on the stand, aligning the front
and sides of the TV with the front and sides of the stand. This will
help properly seat the TV on the positioning dowels and align the
pre-drilled holes on the stand and swivel.
3
Use the supplied screws (2) and screw key to fasten the swivel to
the stand.
4
Place accessory devices—HD satellite receiver, cable box, DVD
player, or VCR, for example—inside the stand. (See the TV Quick
Use and Setup Guide and Directions for Use manual for connec-
tion information.) Route the power cords through the opening in
the bottom of the stand shelf, and route the connection cables
through the openings in the back of the stand.
5
Before swiveling the TV, make sure you have left enough slack in
the cords of any connected accessory devices. This will prevent
damage to the cords.
Connect the cable TV signal to the TUNER jack on the back of
the TV. See page 8 for details on using Autoprogram to store chan-
nels in the TV’s memory.
NOTE: This connection will supply stereo sound to the TV if it is
being broadcast by the station you are watching.
Rubber Locators
Placing the TV on the Stand
without the Swivel
If you should decide not to purchase the optional swivel, you can
place the TV directly on the stand.
• First remove the nut and washer from each supplied rubber
locator (2).
• Place the rubber locators in the pre-drilled holes in the stand.
• Replace the washer and nut on each rubber locator.
• Tighten each nut.
• While aligning the corresponding holes in the bottom of the
TV with the rubber locators, set the TV on the stand. The
rubber locators will prevent the TV from sliding.