Sony RM-D100K Manuel d'utilisation

System adaptor kit, Rm-d100k, Before you begin

Advertising
background image

English

Français

WARNING

To prevent fire or shock hazard,
do not expose the unit to rain
or moisture.
To avoid electrical shock, do not
open the cabinet. Refer
servicing to qualified personnel
only.
Mains cord must only be changed at
qualified service shop.

For the Customers in the U.S.A.

This symbol is intended to
alert the user to the
presence of uninsulated
“dangerous voltage”
within the product’s
enclosure that may be of
sufficient magnitude to
constitute a risk of electric
shock to persons.

This symbol is intended to
alert the user to the
presence of important
operating and maintenance
(servicing) instructions in
the literature
accompanying the
appliance.

WARNING
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful
interference in a residential
installation. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed
and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a
particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
following measures:
– Reorient or relocate the receiving

antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an

outlet on a circuit different from that
to which the receiver is connected.

– Consult the dealer or an experienced

radio/TV technician for help.

CAUTION

You are cautioned that any changes or
modifications not expressly approved
in this manual could void your
authority to operate this equipment.

Before you begin

Thank you for purchasing Sony
RM-D100K! The RM-D100K is the
remote control, timer, and digital
input/output adaptor kit for the
digital audio tape-corder TCD-D100.

Before operating the unit, please read
this manual thoroughly and retain it
for future reference.

This adaptor kit is designed to be
used with the digital audio tape-
corder TCD-D100. It can also be
used with the digital audio tape-
corder TCD-D8/D7/D3.
Please attention to the following.
Notes
Be sure to operate the TCD-D100 on
house current.
• Using batteries may interfere with

the input/output signals and
may cause a malfunction of the
remote commander.

• It is impossible to operate the

TCD-D8/D7/D3 during low-
power consumption mode.

Features

With the RM-D100K connected to
TCD-D100, you can:
– Enjoy wireless control of the

TCD-D100 (including direct
selecting of desired programs, music
scanning, and record muting
operations);

– Connect to other audio equipment

using digital input/output
connectors (both optical and coaxial
digital);

– Make timer-activated recordings and

playbacks on the TCD-D100 (when
used with an audio timer, not
supplied).

System Adaptor Kit

3-859-925-11(1)

RM-D100K

Sony Corporation © 1997 Printed in Japan

Operating Instruction

Mode d’emploi

A

a

Remote control/timer/digital input/output adaptor
RMR-D100 (Front side)

Adaptateur de télécommande/minuterie/entrée/sortie
numériques RMR-D100 (Façade)

Location and
Function of Controls

Remote control/timer/digital
input/output adaptor
RMR-D100 (main unit)

Front side (See fig.

A

-

a

)

1

OPERATE switch and lamp

To remote control the TCD-D100,
set the switch to either STANDBY
or ON. To use the input/output
connectors or to make timer-
activated recording or playback,
set it to ON.

2

Remote sensor

3

INPUT SELECT selector

Selects the input signals of the
TCD-D100 (either digital or
analog).

4

TIMER selector

Rear side (See fig.

A

-

b

)

5

Optical input/output jacks

6

OPTICAL INPUT (optical
digital input) jack

7

OPTICAL OUTPUT (optical
digital output) jack*

8

Special 7-pin connector

9

DIGITAL INPUT selector

! º

COAXIAL INPUT (coaxial
digital input) jack

! ¡

COAXIAL OUTPUT (coaxial
digital output) jack*

!™

Power supply cord

* Whichever position is selected on

the DIGITAL INPUT selector, the
signal of TCD-D100 is output
simultaneously from the OPTICAL
OUTPUT and COAXIAL OUTPUT
jacks.

Remote Commander RMT-D101
(See fig.

A

-

c

)

! £

START ID (AUTO, WRITE,
ERASE, RENUMBER) buttons

For writing or erasing a start ID
and renumbering program
numbers.

! ¢

Numeric buttons, CLEAR,
MUSIC SCAN buttons

For direct selecting.

!

R

button

For record-muting.

! §

C D (

P

,

=

,

+

) b u t t o n s

For remote-control operation of
Sony CD players connected to this
unit.

! ¶

CD SYNCHRO (STOP, START,
STANDBY) buttons

For synchronized recording with
SONY CD players connected to
this unit.

! •

COUNTER (MODE, RESET)
buttons

(have the same function as the
TCD-D100 buttons.)

! ª

Tape operation buttons

r

,

p

,

(

,

P

, buttons:

(have the same function as the
TCD-D100 buttons.)

=

,

+

b u t t o n s :

AMS Function (You can search
for the beginning of a track by
pressing

=

or

+

buttons in

any mode.)

0

,

)

b u t t o n s :

For rewind and fast-forward
during stop mode. For review
and cue during playback mode.
(High speed review and high
speed cue are not possible.)

Precautions

On safety

• Before connecting the RMR-D100

remote control adaptor to the wall
outlet, check to be sure that the
unit’s operating voltage is the same
as your local power supply (see
“Specifications”). Use only the
supplied power cord and no other
type.

• The nameplate indicating operating

voltage, power consumption, etc., is
located on the bottom exterior of the
RMR-D100.

• To operate the commander, use two

R6 (size AA) batteries. Never use
any other type.

• Should any liquid or solid object fall

into the cabinet, unplug the
RMR-D100 and have it checked by
qualified personnel before operating
it any further.

• Unplug the RMR-D100 from the wall

outlet if it is not going to be used for
several days or more. To disconnect
the cord, pull it out by the plug;
never pull the cord itself.

• To avoid damage from battery

leakage, remove the batteries from
the commander when it is not going
to be used for several days or more.

• The unit is not disconnected from

the AC power source (mains) as long
as it is connected to the wall outlet,
even if the unit itself has been turned
off.

On installation

Do not install the kit near heat sources
such as radiators or air ducts, or in
locations subjects to direct sunlight,
excessive dust, excessive moisture,
mechanical vibrations or shock.

On cleaning

Clean the kit with a lightly dampened
soft cloth. Use a mild household
detergent. Never use strong solvents
such as thinner or benzine as they
might damage the unit’s exterior
finish.

If you have any questions or problems
concerning your unit that is not
covered in this manual, please consult
your nearest Sony dealer.

b

(Rear side)

(Arrière)

c

Remote Commander RMT-D101

Télécommande RMT-D101

1

2

3

4

9

!…

!`

!“

5

7

6

8

!⁄

!

START ID

Apparaten bortkopplas inte fran spänningskällan så länge som den är ansluten till
vägguttaget, även om själva apparaten her stängts av.

Netspændingen til dette apparat er IKKE afbrudt, sålænge netledningen sidder i en
stikkontakt, som er tændt-også selvom der er slukket på apparatets netafbryder.

Appratet er forsynet med en speciel netledning, der kun ma udskiftes af et autoriseret
serviceværksted.

AVERTISSEMENT

Afin d’éviter tout risque
d’incendie ou d’électrocution, ne
pas exposer cet appareil à la
pluie ou à l’humidité.
Afin d’éviter tout risque
d’électrocution, ne pas ouvrir le
coffret. Pour toute réparation,
faire appel à un professionnel
uniquement.

Avant propos

Merci d’avoir choisi le Sony
RM-D100K! Le RM-D100K est un
ensemble comprenant entre autres
l’adaptateur de télécommande,
minuterie et entrée/sortie numérique,
conçu pour l’enregistreur
audionumérique TCD-D100.

Avant la mise en service de cet
appareil, prière de lire attentivement
ce mode d’emploi que l’on conservera
pour toute référence future.

Cet ensemble adaptateur est conçu
pour être utilisé avec l’enregistreur
audionumérique TCD-D100. Il
peut être également utilisé avec les
TCD-D8/D7/D3.
Veuillez tenir compte des
recommandations suivantes.
Remarques
Veillez à utiliser le TCD-D100 sur le
courant secteur.
• L’utilisation des piles peut

perturber le signal d’entrée/sortie
et le fonctionnement de la
télécommande.

• Il est impossible de faire

fonctionner le TCD-D8/D7/D3
dans le mode économique.

Caractéristiques

Quand le RM-D100K est raccordé au
TCD-D100, vous pouvez:
– commander à distance le TCD-D100,

en particulier sélectionner des
programmes, rechercher des
passages et enregistrer des passages
silencieux.

– connecter l’appareil à d’autres

appareils audio par les prises
d’entrée/sortie numériques (les
deux prises sont de type optique et
coaxial numérique).

– programmer un enregistrement ou

la lecture sur le TCD-D100, dans la
mesure où vous avez raccordé une
minuterie audio (non fournie).

Emplacement et
fonctions des
commandes

Adaptateur télécommande/
minuterie/entrée/sortie
numériques RMR-D100
(appareil principal)

Façade (Voir fig.

A

-

a

)

1

Commutateur et voyant
OPERATE

Pour la commande à distance du
TCD-D100, réglez le commutateur
sur STANDBY ou ON. Pour
utiliser les prises d’entrée/sortie
numériques ou pour un
enregistrement/lecture
programmé, réglez-le sur ON.

2

Capteur de signaux
infrarouges

3

Sélecteur INPUT SELECT

Permet de sélectionner le signal
d’entrée du TCD-D100
(numérique ou analogique).

4

Sélecteur TIMER

Arrière (Voir fig.

A

-

b

)

5

Prises d’entrée/sortie
optiques

6

Prise OPTICAL INPUT (entrée
numérique optique)

7

Prise OPTICAL OUTPUT*
(sortie numérique optique)

8

Connecteur spécial à 7
broches

9

Sélecteur DIGITAL INPUT

! º

Prise COAXIAL INPUT
(entrée numérique coaxiale)

! ¡

Prise COAXIAL OUTPUT*
(sortie numérique coaxiale)

!™

Cordon d’alimentation
secteur

* Quelle que soit la position de réglage

du sélecteur DIGITAL INPUT, le
signal du TCD-D100 est fourni
simultanément par les prises
OPTICAL OUTPUT et COAXIAL
OUTPUT.

Télécommande RMT-D101
(Voir fig.

A

-

c

)

! £

Touches START ID (AUTO,
WRITE, ERASE, RENUMBER)

Pour inscrire ou effacer des
indices de départ et renuméroter
un programme.

! ¢

Touches numériques,
touches CLEAR, MUSIC
SCAN

Pour la sélection directe d’un
programme.

!

Touche

R

Pour enregistrer un passage
silencieux.

! §

T o u c h e s C D (

P

,

=

,

+

)

Pour le contrôle à distance d’un
lecteur CD Sony raccordé à cet
appareil.

! ¶

Touches CD SYNCHRO
(STOP, START, STANDBY)

Pour l’enregistrement
synchronisé avec un lecteur CD
Sony raccordé à cet appareil.

! •

Touches COUNTER (MODE,
RESET)

Ces touches ont les mêmes
fonctions que les touches du
TCD-D100.

! ª

Touches d’exploitation
Touches

r

,

p

,

(

,

P

:

Ces touches ont les mêmes
fonctions que les touches du
TCD-D100.

T o u c h e s

=

,

+

:

Fonction AMS (permet de
localiser le début d’une plage en
appuyant sur les touches

=

ou

+

dans n’importe quel mode.)

T o u c h e s

0

,

)

:

Pour rembobiner ou bobiner la
bande à partir du mode d’arrêt.
Pour la recherche arrière ou avant
en cours de lecture. (La recherche
rapide avant et arrière n’est pas
possible.)

Précautions

Sécurité

• Avant de raccorder l’adaptateur de

télécommande RMR-D100 à une
prise murale, assurez-vous que sa
tension de fonctionnement est
identique à la tension secteur locale
(voir “Spécifications”). Utilisez
seulement le cordon d’alimentation
fourni à l’exclusion de tout autre.

• La plaque signalétique indiquant la

tension de fonctionnement, la
consommation et d’autres
paramètres, se trouve sous le RMR-
D100.

• Pour faire fonctionner la

télécommande, utilisez deux piles
R6 (format AA) à l’exclusion de
toute autre.

• Si un liquide ou un solide tombe

dans le coffre, débranchez le RMR-
D100 et faites-le vérifier par un
professionnel avant de le remettre en
service.

• Débranchez le RMR-D100 de la prise

murale si vous prévoyez de ne pas
l’utiliser pendant quelques jours.
Pour le débrancher, tirez sur la fiche.
Ne pas tirer sur le cordon
proprement dit.

• Pour éviter tout dommage causé par

l’électrolyte des piles, enlevez les
piles si vous prévoyez de ne pas
utiliser la télécommande pendant un
certain temps.

• L’adaptateur n’est pas débranché de

la source d’alimentation (secteur)
tant qu’il est raccordé à une prise
murale, même s’il a été arrêté.

Installation

Ne pas installer l’ensemble près de
sources de chaleur, comme un
radiateur ou une sortie d’air chaud, ou
dans des lieux exposés à la lumière
directe du soleil, à une poussière et
une humidité excessives, à des
vibrations ou à des chocs.

Nettoyage

Nettoyez l’ensemble avec un chiffon
doux légèrement mouillé d’un
détergent domestique neutre. Ne
jamais utiliser de solvants, comme les
diluants ou la benzine, car ils risquent
d’endommager la finition.

Pour toute question ou problème
concernant cet appareil, non couverts
dans le mode d’emploi, veuillez
consulter votre revendeur Sony.

Specifications

System

Infrared pulse method

Power requirements

RMR-D100:

120 V AC, 60 Hz (the USA
model)
230 V AC, 50 Hz (other models)

RMT-D101:

DC 3 V, two R6 (size AA)
batteries

Power consumption

2.2 W (RMR-D100)

Inputs

Digital coaxial jack (phono-jack)
Digital optical jack (Rectangular-
shaped optical jack)

Outputs

Digital coaxial jack (phono-jack)
75 ohms, 0.5 Vp-p, ±20%
Digital optical jack (Rectangular-
shaped optical jack)
wavelength: 680 nm, –18 dBm

Mass

RMR-D100: approx. 360 g (12.7 oz)
RMT-D101: approx. 130 g (4.6 oz)
including batteries

Dimensions

RMR-D100: approx.
83

Ч

35

Ч

117 mm (w/h/d)

(3

3

/

8

Ч

1

7

/

16

Ч

4

5

/

8

inches)

including projecting parts
RMT-D101: approx.
45

Ч

26

Ч

210 mm (w/h/d)

(1

13

/

16

Ч

1

1

/

16

Ч

8

3

/

8

inches)

including projecting parts

Supplied accessories

R6 (Size AA) batteries (2)

Accessories not supplied

Digital connecting cord (phono-plug)
VMC-10HG (1 m)
Digital cable for optical transmission
(optical plug) POC-5A/5AB (0.5 m),
POC-10A/10AB (1 m),
POC-15A/15AB (1.5 m)

* Your dealer may not handle the

above listed accessories. Please ask
the dealer for detailed information.

Design and specifications are subject
to change without notice.

Spécifications

Système

Impulsions infrarouges

Alimentation

RMR-D100:

120 V CA, 60 Hz
(modèle pour les Etats-Unis).
230 V CA, 50 Hz
(autres modèles)

RMT-D101:

3 V CC, deux piles R6 (format
AA)

Consommation

2,2 W (RMR-D100)

Entrées

Prise coaxiale numérique
(prise cinch)
Prise optique numérique
(prise rectangulair optique)

Sorties

Prise coaxiale numérique
(prise cinch) 75 ohms, 0,5 Vc-c,
±20%
Prise optique numérique
(prise rectangulair optique)
longueur d’onde: 680 nm, –18 dBm

Poids

RMR-D100: env. 360 g (12.7 on.)
RMT-D101: env. 130 g (4.6 on.)
avec les piles

Dimensions hors tout

RMR-D100: env. 83

Ч

35

Ч

117 mm

(l/h/p)
(3

3

/

8

Ч

1

7

/

16

Ч

4

5

/

8

pouces)

compris pièces en saillie
RMT-D101: env. 45

Ч

26

Ч

210 mm

(l/h/p)
(1

13

/

16

Ч

1

1

/

16

Ч

8

3

/

8

po.)

compris pièces en saillie

Accessoires fournis

Piles R6 (format AA) (2)

Accessoires non fournis

Cordon de liaison numérique
(à fiches cinch)
VMC-10HG (1 m)
Câble numérique pour transmission
optique (à fiche optique)
POC-5A/5AB (0,5 m),
POC-10A/10AB (1 m),
POC-15A/15AB (1,5 m)

* Votre revendeur n’aura peut-être

pas en stock tous les accessoires
indiqués. Consultez-le pour les
détails à ce sujet.

La conception et les spécifications
peuvent être modifiées sans préavis.

Advertising