Sunbeam SLP3310-CN - Manuel (Page 2)

PRE-OPERATING INSTRUCTIONS
1. Make sure the heater is OFF before plugging the heater
into the outlet.
2. Place the heater on a firm, level surface.
3. Avoid overloading your circuit by not using other high
wattage appliances in the same outlet. At 1500 Watts,
this unit draws 12.5 Amps.
4. Make sure unit and plug is free of moisture and debris
before plugging into an electrical outlet.
o
perating
i
nStructionS
SLP3310 (Fig. 1)
1. Press the On/Off button to turn unit on.
2. Select temperature by pressing the Temperature button
until the desired temperature is chosen.
3. Set the Timer for the duration in which you would
like the heater to run.
4. Then choose whether or not you would like to
use the Heat & $ave™ Technology by pressing
the Heat & $ave™ button.
c
leaning
/M
aintenance
Always unplug the heater before cleaning and allow to cool.
• Lightly run a vacuum cleaner nozzle over the heater grill
to remove any dust or dirt that may have accumulated.
• Carefully wipe the heater with a soft, damp cloth. Please
be very cautious near the heating elements.
• NEVER use abrasive or flammable solvents to clean
the heater.
• After cleaning, be sure to completely dry the heater with
a cloth or towel.
• Store your heater in a cool, dry dust-free location.
t
roubleSHooting
If your heater fails to operate or if there is no heat:
• Do NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void
the warranty. The inside of the unit contains no user
serviceable parts. All servicing should be performed
by qualified personnel only.
• Make sure the power button is ON – depress button
or turn knob to High.
• Check the thermostat setting; it might be set too low.
Turn the thermostat knob clockwise until the heater
restarts.
• If the unit is still not producing enough heat, or
Thermostat is set to the highest setting.
• Be patient. Give the heater time to heat up.
If your heater shuts down, follow these steps:
• Turn Power to OFF.
• Unplug the heater and wait 30 minutes.
• Plug in the heater, turn the power ON.
• Your heater should now be operating properly.
• Make sure the electrical outlet and circuit breaker
are working.
• You may hear a popping or crackling sound as the heater
heats up. This is normal and safe operation. Once the
heater heats up, the crackling sound will go away.
• Heat & $ave TM automatically shuts off after 4 hours.
Fig. 1 (SLP3310)
Fig. 2 (SLP3300)
HEATER SAFETY
PLEASE READ AND SAVE
THESE IMPORTANT
SAFEGUARDS
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety precautions should
always be followed to reduce the risk of fire, electric shock, and
injury to persons, including the following:
1. Read all instructions before using the appliance.
2. To avoid fire or shock hazard, plug the appliance directly
into a 120V AC electrical outlet.
3. The heater is hot when in use. To avoid burns, DO NOT
let bare skin touch hot surfaces. Use handle when moving
this heater. Keep combustible materials, such as furniture,
pillows, bedding, papers, clothes, and curtains at least 3 ft
(0.9 m) from the front of the heater and keep them away
from the sides and rear.
4. DO NOT run cord under carpeting. DO NOT cover cord
with throw rugs, runners, or the like. Arrange cord away
from traffic area and where it will not be tripped over.
5. This heater is not intended for use in bathrooms, laundry
areas and similar indoor locations. NEVER locate heater
where it may fall into a bathtub or other water container.
6. Extreme caution is necessary when any heater is used by,
or near children or invalids, and whenever the heater is left
operating and unattended.
7. Always unplug the heater when not in use.
8. When unplugging, be sure to pull by the plug and not the
cord.
9. DO NOT insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an electric
shock or fire, or damage the heater.
10. DO NOT operate heater with a damaged cord or plug, or
after the heater malfunctions, or has been damaged in any
manner. Return appliance to manufacturer for examination,
electrical or mechanical adjustment, or repair.
11. A heater has hot and arcing or sparking parts inside. DO
NOT use it in areas where gasoline, paint, or flammable
liquids are used or stored.
12. Use appliance only for intended household use as described
in this manual. Any other use not recommended by the
manufacturer may cause fire, electric shock, or injury to
persons. The use of attachments not recommended or sold
by the manufacturer may cause hazards.
13. DO NOT use outdoors.
14. To prevent a possible fire, DO NOT block air intakes or
exhaust in any manner. DO NOT use on soft surfaces like a
bed, where openings may become blocked.
15. To disconnect heater, turn controls to O position, then
remove plug from outlet.
16. Avoid the use of an extension cord because the extension
cord may overheat and cause a risk of fire. However, if
you have to use an extension cord, the cord should be No.
14AWG minimum size and rated not less than 1875 watts.
17. If the heater will not operate, see specific instructions under
Auto Safety Shut-off on resetting the heater.
18. DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void your
warranty. The inside of the unit contains no user serviceable
parts. All servicing should be performed by qualified
personnel only.
19. DISCONTINUE USE IF PLUG OR OUTLET IS HOT.
RECOMMEND OUTLET BE REPLACED IF PLUG OR
OUTLET IS HOT TO TOUCH.
PLEASE SAVE THESE
INSTRUCTIONS
CONSUMER SAFETY INFORMATION
THIS APPLIANCE HAS A POLARIZED
PLUG (one blade is wider than the other). To
reduce the risk of electric shock, this plug is
intended to fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact
a qualified electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR
DEFEAT THIS SAFETY FEATURE IN ANY WAY.
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
NOTE:
• There may be an odor coming from the heater the first
time you use it or after long periods of storing. This
is normal during the break-in period. Make sure the
heater is in a well ventilated area and continue running
it until the smell goes away.
• You may hear a popping or crackling sound as the heat-
er heats up. This is normal and safe operation. Once the
heater heats up, the crackling sound will go away.
TECHNICAL SPECIFICATIONS
Wattage: 1500W/ (+ 5% - 10%)
Working Voltage: 120V AC/60 Hz
Amperage: 12.5A
ENERGY EFFICIENT HEAT & $AVE™™ TECHNOL-
OGY
(AVAILABLE ON MODEL SLP3310-CN ONLY)
The heater will automatically cycle between 1500 and
750 watts. To activate the Heat & $ave™ cycle depress the
Heat & $ave™ button. The Heat & $ave™ cycle can be
deactivated by depressing the Heat & $ave™ button. In this
case, the heater will run continuously at 1500 watts.
AUTO SAFETY SHUT-OFF
This heater is equipped with a patented, technologically
advanced, safety system that automatically shuts off the
current to the heater when a potential overheat tempera-
ture is reached. The heater can only resume operation
when you reset it.
To Reset the Heater
If your heater shuts down, follow these steps:
1. Turn Power to OFF.
2. Unplug the heater and wait 30 minutes.
3. Plug in the heater, turn the power ON.
4. Your heater should now be operating properly.
Tip-Over Shut-Off
If the heater is knocked over, it will instantly shut off.
To resume operation, simply place the heater in an
upright position and turn ON the heater.
SLP3300 (Fig. 2)
1. To turn heater On simply turn knob to desired heat
level, 1 or 2.
2. Select desired temperature by turning the
thermostat knob.
386259_SLP3300-CN_SLP3310-CN_IB.indd 2 12/8/08 11:35:50 AM