Maytag W10336732A - SP - Manuel (Page 4)

4
Alternate Parts
Your installation may require additional parts. If you are interested
in purchasing one of the items listed here, call the toll-free number
on the cover or in the “Assistance or Service” section.
If You Have You Will Need to Buy
Laundry tub or
standpipe taller
than 96" (2.4 m)
Sump pump system (if not already
available)
Overhead sewer Standard 20 gal. (76 L), 30" (762 mm) tall
drain tub or utility sink and sump pump
(available from local plumbing suppliers)
Floor drain Siphon break, Part Number 285834;
additional drain hose
Part Number 8318155; and connector kit,
Part Number 2858835
Drain hose too
short
4 ft. (1.2 m) drain hose extension kit,
Part Number 2858863
Water faucets
beyond reach of fill
hoses
2 longer inlet hoses:
5ft ( 1.5 m) Black EPDM (2 pack)
8212641RP, 10 ft ( 3.0 m) Black EPDM
(2 pack) 8212656RP
Options
Pedestal
You have the option of purchasing pedestals of different heights
separately for this washer. You may select a 10" (254 mm) or a
15.5" (394 mm) pedestal. The pedestal will add to the total height
of the washer.
Optional pedestal
Pedestal
Height Approximate
Height with
Washer
Color Model
Number
10" (254 mm) 46" (1168 mm) White WHP1000SQ
15.5" (394 mm) 51.5" (1308 mm) White WHP1500SQ
15.5" (394 mm) 51.5" (1308 mm) Lunar
Silver
XHP1550WL
Stack Kit
Are you planning to stack your washer and dryer? To do so you will
need to purchase a Stack Kit.
To order, call the dealer from whom you purchased your washer or
refer to the “Assistance or Service” section. Ask for Part Number
8572546.
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
Your washer can be installed under a custom counter, or in a
basement, laundry room, closet, or recessed area. See “Drain
System.”
Companion appliance location requirements should also be
considered. Proper installation is your responsibility.
You will need:
■ A water heater set to deliver 120°F (49°C) water to the washer.
■ A grounded electrical outlet located within 6 ft. (1.8 m) of where
the power cord is attached to the back of the washer. See
“Electrical Requirements.”
■ Hot and cold water faucets located within 4 ft. (1.2 m) of the hot
and cold water fill valves, and water pressure of 20-100 psi
(137.9-689.6 kPa).
■ A level floor with a maximum slope of 1" (25 mm) under entire
washer. Installing the washer on soft floor surfaces, such as
carpets or surfaces with foam backing, is not recommended.
■ A sturdy and solid floor to support the washer with a total weight
(water and load) of 400 lbs (180 kg).
Do not operate your washer in temperatures below 32°F (0°C).
Some water can remain in the washer and can cause damage in low
temperatures.
Installation clearances
■ The location must be large enough to allow the washer door
to be fully opened.
■ Additional spacing should be considered for ease of installation
and servicing. The door opens more than 90°, and it is not
reversible.
■ Additional clearances might be required for wall, door, and floor
moldings.
■ Additional spacing of 1" (25 mm) on all sides of the washer
is recommended to reduce noise transfer.
■ Companion appliance spacing should also be considered.
Washer Dimensions
50 1 /
4
"
(1276 mm)
27"
(686 mm)
36"
(914 mm)
30 1 / 2 "
(775 mm)