Faber Agio - Manuel (Page 7)

Version 10/05 - Page 7
Three Screws
Rangehood Body
Front
Strip
CUSTOMIZING YOUR RANGEHOOD
The front strip of the rangehood can be customized by replac-
ing the factory supplied strip with a custom front strip made
from the same materials as your cabinets. The front strip is
attached to the rangehood by three recessed screws and
three key hole slots on the back side of the strip as indicated
in FIGURE 15. It is necessary only to remove the three lower
screws to remove the front strip. The top screws will slide out
of the key holes once the three lower screws are removed.
Side View of the Rangehood
The front strip dimensions are given in FIGURE 16. For a
custom front strip, a local cabinet shop can make a strip to
match your cabinets. If you wish to keep the frame of the front
panel and only replace the glass panel, the dimensions follow:
Height = 5 11/16", Depth = 1/8", Width = 29 11/16" (for 30"
model) 35 11/16" (for 36" model) 23 5/8" (for 24" model).
WARRANTY & SERVICE
All Faber products are warranteed against any defect in materials or
workmanship for the original purchaser for a period of 1 year from the
date of original purchase. This warranty covers labor and replace-
ment parts. The warranty does not cover consumable parts such as
filters and light bulbs. This warranty does not apply if this product
has been subjected to faulty installation, misuse, or neglect. This
warranty excludes any consequential expense or damage resulting
from any use or malfunction of the product. All implied warranties
are limited to the duration of this warranty.
To obtain warranty service, contact the dealer from whom you pur-
chased the rangehood, or the local Faber distributor. If you cannot
identify a local Faber distributor, contact us at (508) 358-5353 for
the name of a distributor in your area.
FIGURE 16
WIRING DIAGRAM
• This rangehood uses Flourescent Lamp Type F33-15W-T8 and
Starter Type S2.
Rangehood Control Panel
All controls are located under the front panel and are shown in
FIGURE 17.
Light On/Off Switch ( L )
On/Off switch for the fluorescent light. Moving the switch to the
1 Position turns the light On. Moving the switch to the 0 Position
turns the light Off.
FIGURE 15
FIGURE 17
FIGURE 18
Blower Speed Switch ( S )
Controls blower speed. Moving the switch to the 1 Position turns
the blower on LOW. Moving the switch to the 2 Position turns the
blower on MEDIUM. Moving the switch to the 3 Position turns the
blower on HIGH.
Operation Indicator Light ( I )
Red light will be on when the rangehood is operating.
Microswitch ( MS )
When the front panel of the rangehood is closed, the rangehood
will turn off by a microswitch. This turns the rangehood On and
Off without adjusting the switches for the Light or Blower and it
remembers the last speed setting.
Cleaning
The metal grease filters should be cleaned frequently in hot deter-
gent solution or placed in the dishwasher. Clean exterior surfaces
with hot soapy water. Using abrasives and scouring agents can
scratch rangehood finishes and should not be used to clean finished
surfaces.
Replacing the Fluorescent Light
To replace the fluorescent light, remove the retainer clips from both
ends of the glass diffuser as indicated in FIGURE 18. Carefully
slide the glass diffuser all the way to the left. Lower the right end
of the glass below the support flange, then remove the glass by
sliding it back to the left. Replace the diffuser glass by reversing
these directions.
23 5/8" or 29 15/16" or 35 15/16"
5 7/8"
13/16"
USE AND CARE INFORMATION
This rangehood system is designed to remove smoke, cooking
vapors and odors from the cooktop area.
For Best Results
Start the rangehood several minutes before cooking to develop proper
airflow. Allow the unit to operate for several minutes after cooking
is complete to clear all smoke and odors from the kitchen.
Blower On/Off
Switch ( M )
On/Off switch for the
blower. Moving the
switch to the 1 Posi-
tion turns the blower
On. Moving the switch
to the 0 Position turns
the blower Off.